Dacor IF36RNBOL manual Plug in Refrigerator, Move to Final Location, Connecting to Refrigerator

Page 17

Installation Instructions

5.Using a cordless drill, drill a ¼” (6.35 mm) hole in the cold water pipe you have selected.

 

A

G

B

 

 

C

F E

D

A. Cold water pipe

E. Compression sleeve

B. Pipe clamp

F. Shutoff valve

C. Copper tubing

G. Packing nut

D. Compression nut

 

6.Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¼” (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten, or you may crush the copper tubing.

7.Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten the clamp or the sleeve to prevent crushing of the copper tubing.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

8.Turn off the shutoff valve on the water pipe. Coil the copper tubing.

9.Check for leaks around the saddle valve.

Connecting to Refrigerator

1.Unplug the refrigerator or disconnect power.

2.Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.

3.Measure the distance from the shutoff valve to the opening in which the refrigerator will be located. Tubing must be extended from the shutoff valve into the refrigerator opening following specific guidelines. See Water Supply Requirements.

4.A ¼” x ¼” (6.35 mm to 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

A

B

C

D

E F G

A. Water tubing

 

 

E. Ferrule (purchased)

B. Nut

 

 

F. Nut (purchased)

C. Bulb

 

 

G. Household water line (as

D. Coupling (purchased)

 

connected in previous section)

5.Turn shutoff valve on.

6.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

7.Plug in the refrigerator or reconnect power.

8.Flush the water system. See Water System Preparation.

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

Plug in Refrigerator

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1.Set control switch at top of cabinet to the off position.

2.Plug into a grounded 3 prong outlet.

Move to Final Location

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: To avoid floor damage, make sure levelers are raised (not touching floor) and refrigerator is on rollers before moving.

1.Place top of cardboard carton or plywood under refrigerator. Remove dolly.

2.Do not remove protective film or cover.

3.Move the refrigerator straight back, evenly into the opening. Be sure that the refrigerator side trims are not interfering with the door opening. Also, be sure that the water tubing is not kinked and the power supply cord is on top of the refrigerator.

15

Image 17
Contents Installation Instructions Inch Built-In Refrigerator Customer Service Information Table of ContentsRefrigerator Safety EF36LNBSS Model IdentificationOpening Dimensions Installation RequirementsTools and Parts Location RequirementsRecommended Grounding Method Electrical RequirementsLocation Requirements Tipping Radius Water Supply RequirementsWater Pressure Side Tipping RadiusDoor Swing Dimensions Product DimensionsSide View Top ViewDoor Swing Actual Size Refrigerator to Cabinet Clearance Door Panels and Cabinet Clearance IF36 Series ModelsAnel Door Swing 90 Actual Size Refrigerator to Cabinet ClearanceCustom Panels and Handles IF36 Series Models Install the panels after moving the refrigerator into placeWeight of the overlay panels cannot exceed Piece Door Overlay Panel Configuration Piece Grille Overlay Panel ConfigurationPiece Overlay Panel Configuration Custom Panels Construction InformationInset Installation Dimensions Refrigerator and Side Trim DimensionsRecessed Inset Installation Dimensions Custom Side Panels Model IF36Custom Side Panels Model EF36 Flush Installation DimensionsBack Wall Refrigerator BackUnpack the Refrigerator Installation InstructionsReduce Tipping Radius Move Refrigerator into HouseConnect the Water Supply Install Anti-Tip BoardsStyle 1 Shutoff Valve Connection Style 2 Copper Line ConnectionMove to Final Location Connecting to RefrigeratorPlug in Refrigerator After moving the refrigerator to its final location Level and Align RefrigeratorDoor Panel Installation Custom Panel and Handle Installation IF36 Series ModelsHandle Installation Custom Panel Installation IF36 Series Models Adjust DoorsDoor Swing Adjustment Door-to-Door or Door-to-Refrigerator Trim AdjustmentInstall Base Grille Install Side PanelsWater System Preparation Complete InstallationInstructions d’installation Réfrigérateur Encastré de Exigences d’installation Information pour le service à la clientèleSécurité du réfrigérateur Identification des modèles Exigences d’emplacement Exigences d’installationDimensions de l’ouverture Outillage et composantsSpécifications électriques Exigences d’emplacement suiteMéthode recommandée de liaison à la terre Exigences de l’alimentation en eau Rayon de basculementPression de l’eau Rayon de basculement latéralDimensions pour le pivotement des portes Dimensions du produitVue latérale Vue avantPosition de butée 110˚ Dégagement Réfrigérateur/placardPivotement à 90 Dimensions réelles Panneaux et poignées personnalisés modèle de la série IF36 Panneau décoratifs Dimensions Panneau d’appui DimensionsPoignées personnalisés Information sur la construction des panneaux personnalisésDimensions pour une installation en encastrement Dimensions du réfrigérateur et des garnitures latéralesDimensions pour une installation en encastrement en retrait Panneaux latéraux personnalisés modèle IF36Dimensions pour une installation en affleurement Déballage du réfrigérateur Instructions d’installationFaire entrer le réfrigérateur dans le domicile Réduction du rayon de basculement si nécessaireRaccordement à la canalisation d’eau Installation de planches antibasculementInstallation de planches antibasculement Raccordement au réfrigérateur Brancher le réfrigérateurRéglage de l’aplomb et alignement du réfrigérateur Installation du panneau de porte Installation de la poignéeRéglage de l’angle d’ouverture de la porte Réglage des portesPanneau de la grille supérieure Installation de la grille de la base Installation des panneaux latérauxPréparation du système d’eau Achever l’installationPage Page