Cisco Systems OL-12397-13 manual Planning VSCs In Networks with SIP Subscribers

Page 24

Chapter 2 SIP Subscribers

Cisco BTS 10200 Softswitch-Based Features

Planning VSCs In Networks with SIP Subscribers.

Some features require SIP subscriber to enter a series of numbers and characters on the SIP client or handset. Typically, the subscriber dials VSC digits followed by additional dialing keys representing the parameters for the feature call. For MGCP subscribers, the BTS 10200 sends a response tone or announcement between the VSC code and the additional digits. However, for SIP endpoints, all the digits are dialed at a stretch without waiting for an intervening response tone from the BTS 10200. The following paragraph explains how certain combinations of VSC can cause mismatches between the feature the subscriber is attempting to manage versus the response of the BTS 10200, and how to plan VSCs to avoid these mismatches.

You should not deploy certain combinations of VSCs on networks with SIP endpoints. If you deploy a VSC longer than 2 digits, make sure that the longer VSC does not begin with the same sequence of characters as one of the shorter VSCs. In some cases, the system might match the shorter string even if the subscriber dialed the longer string. Consider the following example, for which the subscriber is expected to dial a VSC followed by a DN.

A SIP subscriber is provisioned with *93 for Feature1 and *938 for Feature2, and dials *938+2135551801 to invoke Feature2. The BTS 10200 receives *9382135551801 in the INVITE message. By default, it takes the first six characters, in this case *93821, and uses this string to look up the feature in the VSC table. There is no match for *93821, therefore the BTS 10200 proceeds as follows. First, it uses *9 to look for a match in the VSC table and it cannot be found. Then it uses *93, finds a match, and delivers Feature1. This is incorrect. The user's intention was to invoke Feature2 and not Feature1. The solution is for the service provider to change one of the two VSCs (either *93 or *938) in the VSC table.

Supported VSC-Enabled Features for SIP Endpoints

The following BTS 10200 Vertical Service Code (VSC) features are supported on SIP endpoints:

•Calling identity delivery and suppression, suppression part (CIDSS)

•Calling identity delivery and suppression, delivery part (CIDSD)

•Calling name delivery blocking (CNAB)

•Outgoing call bearing activation (OCBA), outgoing call bearing deactivation (OCBD), outgoing call bearing interrogation (OCBI)

•Call forwarding unconditional activation (CFUA), call forwarding unconditional deactivation (CFUD), call forwarding unconditional interrogation (CFUI)

Reminder ringback cannot be enabled for SIP subscribers. If you are turning on the Call Forward Unconditional (CFU) feature for a SIP subscriber, make sure that reminder ring capability is turned off. This should be done at a subscriber level.

Here is the command format at the feature level:

add feature fname=CFU; tdp1=TERMINATION_ATTEMPT_AUTHORIZED; tid1=TERMINATION_ATTEMPT_AUTHORIZED; feature_server_id=FSPTC235; ttype1=R; fname1=CFUA; fname2=CFUD; type1=MCF; value1=Y; type2=RR; value2=N; description=CFU MCF multiple call forwarding allowed, RR ring reminder not allowed;

And at the subscriber feature level:

add subscriber-feature-data sub_id=sip_sub2; FNAME=CFU; type2=RR; VALUE2=N;

 

Cisco BTS 10200 Softswitch SIP Feature and Provisioning Guide, Release 5.0

2-24

OL-12397-13

Page 23 Page 25
Image 24
Page 23 Page 25
Contents SIP Subscribers A P T E RSIP Phone Initialization Provisioning a SIP SubscriberSIP Registration and Security Enhanced SIP Registration DescriptionProvisioning Commands ExampleEnable or Disable Secure Fqdn for an Existing Subscriber Provision a New SIP SubscriberOperations Cisco BTS 10200 Challenges RegistrationRegistration Expires Call Processing ValidationReceived SIP Response Message SecurefqdnEvents and Alarms MeasurementsRules for Sending a SIP Invite Message from the BTS Validation of ACK RequestSIP User Authentication AORSIP Subscriber Calls Provisioning Session Timers for SIP Subscribers SIP Timer Values for SIP SubscribersDiversion Indication for SIP Subscribers ACR AcractAcrdeact AcactCFB CfbvaCfbvd CfbiCwdi CidsdCidss CidcwDrcw DrcwactDND DndactOcba OcbdOcbi OsfgCisco BTS 10200 Softswitch-Based Features SummaryCPT CidsCall Forwarding Call Forwarding Activation and DeactivationDetailed Provisioning Procedure and Feature Description Calling Name and Number DeliveryCall Forwarding to an E.164 Number or an Extension Number Customer Access Treatment Caller ID Delivery SuppressionDirect Inward Dialing Direct Outward Dialing Do Not DisturbOperator Services 0-, 0+, 01+, and 00 Calls Vertical Service Code FeaturesCentrex Dialing Plan Extension Dialing User-Level PrivacySupported VSC-Enabled Features for SIP Endpoints Planning VSCs In Networks with SIP SubscribersVoice Mail VM ActionsVM Deposit MWI NotificationVM Implementation for Centrex Subscribers Retrieving VMCalling Back a Message Depositor VM Within a Single Centrex Group Add the SIP trunk groupProvisioning Voice Mail Across Multiple Centrex Groups Jointly Provided Features Text-GUI FeaturesSupported Features Accessing FeaturesSupported Handsets SIP HandsetCall Transfer Blind and Attended with Refer SIP Software ClientsPhone-Based Features Distinctive RingingDistinctive Ringing for Centrex did Calls CwcidSIP Subscribers Phone-Based Features OL-12397-13

OL-12397-13 specifications

Cisco Systems OL-12397-13 refers to a specific training course or certification related to Cisco's networking technologies and solutions. While precise details about OL-12397-13 may vary, it typically encompasses various features, technologies, and characteristics central to Cisco's offerings in networking and cybersecurity.

One main feature of the course is its comprehensive curriculum designed to provide learners with in-depth knowledge of Cisco’s networking architecture and best practices. The course often covers topics such as routing and switching, network security, wireless networking, and automation, enabling participants to understand the complex interactions within a network environment.

Another significant inclusion in the OL-12397-13 curriculum is an emphasis on emerging technologies. This may include training on software-defined networking (SDN), Internet of Things (IoT) solutions, and cloud-based networking. By integrating these modern frameworks, participants can grasp how to manage and optimize their network infrastructures for current and future demands.

A key characteristic of Cisco certification courses is the hands-on training component. Classes may involve lab sessions where students can apply theoretical knowledge practically by configuring devices, troubleshooting network issues, and implementing security protocols. This experiential learning ensures that learners are prepared to face real-world networking challenges.

The course also aims to instill best practices in network management and monitoring. Concepts such as network design, implementation strategies, and the use of network management tools are pivotal to ensuring efficient and secure operations within an organization.

Moreover, the emphasis on security throughout the OL-12397-13 course reflects the growing need for robust cybersecurity measures in networking. Participants are taught how to identify vulnerabilities, implement security measures, and respond to potential threats, which is crucial in today’s digital landscape.

Networking professionals pursuing Cisco certifications find OL-12397-13 to be instrumental in developing their skill sets, enhancing their career prospects, and enabling them to contribute effectively to their organizations. Overall, OL-12397-13 serves as a gateway for individuals looking to solidify their understanding of Cisco's technologies while preparing for future advancements in the field of networking. With a focus on both foundational knowledge and cutting-edge trends, it positions learners to excel in a rapidly evolving tech landscape.
Top Page Image Contents