Zanussi ZSF 6280 manual Setting electronically, Water hardness Adjusting the hardness setting

Page 11

Setting electronically:

1.Press the ON/OFF button.

3If the name of a programme stage is displayed in the display, a dishwashing cycle is active. First of all you must cancel the dishwashing cycle:

Press the Cancel button. CONFIRM CANCEL? appears in the display.

Press the Ok/Start button. This cancels the dish- washing cycle.

2.Go to the WATER HARDNESS setting; see section “Adapting an option/setting”.

3.Set WATER HARDNESS to the right setting.

If the water softener is set electronically to “1” this switches off the display of the REFILL SALT mes- sage.

 

Water hardness

 

Adjusting the hardness setting

 

 

 

 

 

in °d1)

in mmol/l2)

Range

Manual

Electronic

51 - 70

9,0 - 12,5

 

 

103)

43 - 50

7,6 - 8,9

 

 

9

37 - 42

6,5 - 7,5

IV

1

8

29 - 36

5,1 - 6,4

 

 

7

23 - 28

4,0 - 5,0

 

 

6

 

 

 

 

 

 

 

19 - 22

3,3 - 3,9

III

 

5

15 - 18

2,6 - 3,2

 

4*

 

 

 

 

 

 

 

11 - 14

1,9 - 2,5

II

0*

3

4 - 10

0,7 - 1,8

I/II

 

2

 

 

 

 

 

below 4

below 0.7

I

 

1

 

no salt necessary

 

 

 

 

 

 

 

 

 

1)(°d) German degree, measure of the hardness of water

2)[mmol/l] millimol per litre, international unit for water hardness

3)On this setting the length of the dishwashing cycle may be slightly longer. *) factory setting

11

Image 11
Contents ZSF Dear Customer Following symbols are used in the textContents General Safety SafetyPrior to using for the first time Child SafetyDishwasher door safety catch Control Panel Diagram of ApplianceSwitching on for the first time setting the language Display Options menu Settings sub-menuBasic operation Programmes menuSetting manually Prior to Using for the First TimeAdjusting an option/setting Setting the Water SoftenerRange Manual Electronic Setting electronicallyWater hardness Adjusting the hardness setting Adding dishwasher Salt Only when using the dishwasher for the first timeFilling Up with Rinse Aid Setting the Amount of Rinse Aid Required Setting the acoustic signalLoading cutlery and dishes Daily useLoading cutlery Pots, Pans, Large Plates Cups, Glasses, Coffee ServicePage Upper basket Lower basket Adjusting the Height of the Upper BasketRaising / Lowering the upper basket Maximum height of dishesAdding Detergent Detergent tablets Concentrated detergentsIf you want to use 4in1 products Using 3in1 detergentsIf you want to use 3in1 products If you do not want to use 3in1 products any moreSelecting the dishwashing cycle Cycle Table Selecting a programme Starting a Dishwashing Cy- cle Setting the Delay TimerInterrupting or Cancelling a dish- washing cycle Removing the Dishes Switching Off the dish- washerButton lock Cleaning the filters Care and cleaningUpper basket spray arm Cleaning the spray arm jetsBottom spray arm Malfunction Possible cause Remedy Resetting the languageWhat to do if … Remedying small malfunc- tionsLong warning tone can be BlockedThere are dried water drops on the glass- es and dishes If the Dishwashing Results are not SatisfactoryDishes are still dirty Dishes do not dry and are not shin- ingOld appliance DisposalPackaging material Dishwasher Free-standing appliances Technical dataUpper basket Sample loading arrangementsSafety Information for the Installation Installing the Dishwasher Free-standing appliances Permitted water pressure Connecting the dishwasherConnecting to the water supply Connecting the inlet hoseWater drainage if the dishwasher is built- in at high level Anti-flood systemExtension hoses Sink outlet connectionChanging a fuse Electrical ConnectionConnecting systems Customer Care Department 0870 5 929822 612 Subject to change without notice