Sherwood R-671 Setting the Speaker Setup, When selecting the Auto Speaker Setup, Preparations

Page 42

SETTING THE SPEAKER SETUP

•After you have installed this receiver and connected all the components, you should adjust the speaker settings for the optimum sound acoustics according to your environment and speaker layout.

•Even when you change speakers, speaker positions, or the layout of your listening environment, you should adjust the speaker settings, too.

■Note:

• Because the microphone for Auto Speaker Setup is designed for use with this receiver, to use the auto speaker setup function, do not use a microphone other than the one supplied with this receiver.

When selecting the AUTO SPEAKER SETUP

•Auto Speaker Setup lets you avoid troublesome listening-based speaker setup and achieve good surround sound. You should connect the supplied microphone to the SETUP MIC jack so that this receiver can analyze the information from a series of test tones emitted from speakers and can adjust the size, distance and sound level of each speaker automatically.

•If you want to personalize your speaker setup and channel level setup by making the settings manually, perform the “When selecting the MANUAL SPEAKER SETUP” procedure on page 42, “Adjusting each channel level with test tone” procedure on page 31 and “Adjusting the current channel level”on page 32.

■Preparations

1.Connect the supplied microphone to the SETUP MIC jack on the rear panel,(For details, refer to “CONNECTING MICROPHONE” on page 9)

2.Place the microphone on a flat level surface at your normal listening position.

•If possible, use a tripod, etc. to attach the microphone at the same height as your ears would be when you are seated in your listening position.

•Ensure there are no obstacles between the speakers and the microphone.

Press the CURSOR UP(▲)/DOWN(▼)

1 buttons to select the AUTO SPEAKER SETUP, then press the ENTER button.

Press the CURSOR UP(▲)/DOWN(▼)/

2 LEFT(◀)/RIGHT(▶) buttons to specify the setting condition according to the number of speakers installed and speakers’ frequency characteristics.

•To specify the layout of the installed speakers, press the CURSOR UP(▲) or DOWN(▼) button.

•To specify the crossover frequency, press the CURSOR LEFT(◀) button.

You can specify the crossover frequency with the range of 40~130 Hz in 10 Hz intervals.

•To specify the subwoofer, press the CURSOR RIGHT(▶) button.

41

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Page Introduction Read this Before Operating Your UnitSafety Instruction Contents System Connections Connecting Video Components Connecting Audio Components Connecting System Control Speaker placement AC Input Cord Front Panel Controls Video 3 Input Jacks Universal Remote Controls Digi link system remote controlsFunction Table of the Numbered Buttons Remote Control Operation Range Loading BatteriesUsing Functions of Remote Control Entering a setup codeUsing a punch-through function Programming a macro function Operating a macro functionSpeaker Setup Setting the Speaker Setup Manually Before setting the speaker setupFront R Setting the Speaker Setup Automatically Auto Speaker Setup When specifying the number of speakers installed When specifying the subwoofer or the crossover frequencyWhile displaying SET MEMO, check Listening to a Program Source Before operationWhen CD, Video 1~3 is selected as An input sourceAdjusting the tonebass and treble Enter the tone modeSurround Sound Surround modesDolby Virtual Speaker Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby HeadphoneSelectable surround mode Enjoying Surround SoundListening in a Dolby Headphone mode To cancel the surround mode for stereo operation2CH downmix mode Adjusting each channel level with test tone Adjusting the current channel level Channel is selected as followsMemorizing the adjusted channel levels 32, press the MEMORY/ Enter buttonRecalling the memorized channel levels Auto tuning Manual tuning Presetting radio stationsListening to Radio Broadcasts Tuning to preset stations Memory Backup FunctionRecording with Tape Dubbing the audio and video signalsRecording Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timer Adjusting the brightness of the fluorescent displays Compressing the dynamic range Dolby Digital sources onlyUsing the OSD Current Status DisplayWhen selecting the Speaker Setup Setting the Speaker Setup When selecting the Auto Speaker SetupPreparations When selecting the Manual Speaker Setup Page When selecting the Digital Input Selecting the FunctionWhen selecting the Video Select When selecting the Tone ControlSelecting the Surround Mode Setting the CH Level Setup Recalling the memorized channel levels Troubleshooting Guide Specifications Setup Code Table VCR KLH DVD AUX-TAPE/MD AUX-HOME Automation
Top Page Image Contents