Sherwood R-671 manual Specifications

Page 51

Specifications

AMPLIFIER SECTION

.......................................................................................... 2 X 100 W

• Power output stereo mode, 6Ω, THD 0.2%, 40Hz ~ 20 KHz

• Total harmonic distortion, 6Ω, 95 W, 1 KHz

0.09 %

• Intermodulation distortion

 

60 Hz : 7 KHz = 4 : 1 SMPTE,6Ω, 95 W

0.1 %

• Input sensitivity / impedance

 

Line (CD, TAPE, VIDEO)

230 mV/47 KΩ

• Signal to noise ratio, IHF "A" weighted

 

Line (CD, TAPE, VIDEO)

90 dB

• Frequency response

 

Line (CD, TAPE, VIDEO), 20 Hz~50 KHz

230 mV/47 KΩ

• Out put level

 

TAPE REC, 2.2 kΩ

200 mV

• Bass/Treble control, 100 Hz/10 kHz

±10 dB

• Surround mode, only channel driven

 

Front power output, 6 Ω ,1 kHz, THD 0.7

110 W+110 W

Center power output, 6 Ω, 1 kHz, THD 0.7 %

110 W

Surround power output, 6 Ω, 1 kHz, THD 0.7 %

110 W+110 W

Surround back power output, 6 Ω, 1 kHz, THD 0.7 %

110 W

DIGITAL AUDIO SECTION

32, 44.1, 48, 96 kHz

• Sampling frequency

• Digital input level

 

Coaxial, 75

0.5 Vp-p

Optical, 660 nm

-15~-21 dBm

VIDEO SECTION

NTSC

• Video format

• Input sensitivity(=Output level), 75 Ω

 

Video (Composite(normal))

1 Vp-p

S-Video (luminance signal)

1 Vp-p

(chrominance signal)

0.286 Vp-p

Component video (R-Y signal)

0.5 Vp-p

(B-Y signal)

0.5 Vp-p

(Y signal)

1.0 Vp-p

FM TUNER SECTION

87.5~108 MHz

• Tuning frequency range

• Usable sensitivity, THD 3%, S/N 30 dB

12.8 dBf

• 50 dB quieting sensitivity, mono/stereo

20.2 / 45.3 dBf

• Signal to noise ratio, 65 dBf, mono/stereo

70 / 65 dB

• Total harmonic distortion, 65 dBf,1 kHz, mono/stereo

0.5 / 0.8 %

• Frequency response, 30 Hz~15 kHz

±3 dB

• Stereo separation, 1 kHz

32 dB

• Capture ratio

4.0 dB

• IF rejection ratio

60 dB

AM TUNER SECTION

• Tuning frequency range

........................................................................................................................................... 520~1710 kHz

• Usable sensitivity

500 µV/m

• Signal to noise ratio

40 dB

• Selectivity

25 dB

GENERAL

120 V ~ 60 Hz

• Power supply

• Power consumption

2.7 A

• Switched AC outlets

TOTAL 100 W, 1 A max.

• Dimensions (W×H×D)

440×141×330 mm(17-3/8×5-1/2×13 inches)

• Weight (Net)

10.1 kg (22.3 Ibs)

Note: Design and specifications are subject to change without notice for improvements.

50

Image 51
Contents Page Read this Before Operating Your Unit IntroductionSafety Instruction Contents System Connections Connecting Video Components Connecting Audio Components Connecting System Control Speaker placement AC Input Cord Front Panel Controls Video 3 Input Jacks Digi link system remote controls Universal Remote ControlsFunction Table of the Numbered Buttons Loading Batteries Remote Control Operation RangeEntering a setup code Using Functions of Remote ControlUsing a punch-through function Operating a macro function Programming a macro functionSpeaker Setup Before setting the speaker setup Setting the Speaker Setup ManuallyFront R Setting the Speaker Setup Automatically Auto Speaker Setup When specifying the subwoofer or the crossover frequency When specifying the number of speakers installedWhile displaying SET MEMO, check Before operation Listening to a Program SourceAn input source When CD, Video 1~3 is selected asEnter the tone mode Adjusting the tonebass and trebleSurround modes Surround SoundDolby Headphone Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby Virtual SpeakerEnjoying Surround Sound Selectable surround modeListening in a Dolby Headphone mode To cancel the surround mode for stereo operation2CH downmix mode Adjusting each channel level with test tone Channel is selected as follows Adjusting the current channel levelMemorizing the adjusted channel levels 32, press the MEMORY/ Enter buttonRecalling the memorized channel levels Auto tuning Manual tuning Presetting radio stationsListening to Radio Broadcasts Memory Backup Function Tuning to preset stationsDubbing from video components onto Dubbing the audio and video signalsRecording Recording with TapeDigital Audio Recording with MD Recorder Compressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCurrent Status Display Using the OSDWhen selecting the Speaker Setup Setting the Speaker Setup When selecting the Auto Speaker SetupPreparations When selecting the Manual Speaker Setup Page Selecting the Function When selecting the Digital InputWhen selecting the Tone Control When selecting the Video SelectSelecting the Surround Mode Setting the CH Level Setup Recalling the memorized channel levels Troubleshooting Guide Specifications Setup Code Table VCR KLH DVD AUX-TAPE/MD AUX-HOME Automation