USING FUNCTIONS OF REMOTE CONTROL
•This remote control can control up to 8 different components.
•Before operating audio and video components other than this receiver with using this remote control, the setup code for each component should be entered.
•For system remote control operation, “000” was stored previously in the memory of the device button “CD” for Sherwood CD player, “DVD” for Sherwood DVD player and “AUX” for Sherwood tape deck respectively as its factory setup code. So, you don’t need to enter its code for each Sherwood component except in such a case that its code does not work.
| Entering a setup code |
|
|
|
|
|
|
|
|
| |||||||||||||
| 1 | Turn on the component you want to | 2 | Find the setup codes according to the | |||||||||||||||||||
| control. | type and the brand name of your | |||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| component, referring to “Setup Code | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Table” on page 51. | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 3 | Press and hold down both the “ENTER” | 4 | Enter a 3 digit code, aiming the remote | |||||||||||||||||||
| button and the desired one of the | control at the remote sensor on the | |||||||||||||||||||||
| DEVICE buttons for more than 1 | component. | |||||||||||||||||||||
|
| second. |
| Example) When entering “001”. | |||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| • If entering is performed successfully, the LED will | |
• The LED will flicker once. | flicker twice. | ||
|
| • To be sure that the setup code is correct, press the | |
Note: |
| POWER(or STANDBY) button. | |
• The “AUD” button is unavailable for the audio | If your component is tuned off, the setup code is | ||
components other than this receiver. | correct. | ||
|
| • When your component is not turned off, repeat the | |
|
| above steps ② to ④, trying each code for your | |
|
| component until you find one that works. | |
|
| Notes: | |
|
| • If the LED did not flicker twice, then repeat the | |
|
| above steps ③ to ④ and try entering the same | |
|
| code again. | |
|
| ||
| Repeat the above steps ① to ④ for | • Manufacturers may use different setup codes for | |
5 | the same product category. For that reason, it is | ||
each of your components. | important that you check to see if the code you | ||
| |||
|
| ||
|
| have entered operates as many controls as | |
|
| possible. If only a few functions operate, check | |
|
| to see if another code will work with more | |
|
| buttons. | |
|
| • When operating a Sherwood CD player or tape | |
|
| deck using the system remote control, aim the | |
|
| remote control at the REMOTE SENSOR on this | |
|
| receiver. | |
|
| However, in case of Sherwood DVD player and | |
|
| MD recorder, aim it at the REMOTE SENSOR on | |
|
| the corresponding component. |
15