Sherwood R-771 manual When selecting the SPEAKER X-OVER, About the crossover frequency, English

Page 49

When selecting the SPEAKER X-OVER

ENGLISH

When selecting the SPEAKER X-OVER

•When speakers are set to "SMALL", be sure to set their crossover frequency correctly according to their frequency characteristics.

Press the CURSOR UP( )/DOWN( ) buttons to select the SPEAKER X-OVER, then press

1 the ENTER button.

Press the CURSOR UP( )/DOWN( ) buttons to select the desired speaker.

2

Note :

• You cannot select the subwoofer and the speakers set to "NONE".

Press the CURSOR LEFT( )/RIGHT( ) buttons to set the crossover frequency as desired.

3

• You can adjust the crossover frequency within the range of 40 ~ 200 Hz in 10 Hz intervals.

4	Repeat the above steps and until the crossover frequencies are all set as desired.

About the crossover frequency

•When speakers are set to "SMALL", low frequencies in those channels that are below the crossover frequency are to output from subwoofer or front speakers which are set to LARGE(when not using a subwoofer).

•Refer to the operating instructions of the speakers to be connected. If the frequency range of your speaker is 100 Hz~20 kHz, the crossover frequency should be set to 100 Hz(or slightly higher).

48

Image 49

Contents Page Page SAFETY INSTRUCTIONS ENGLISHIntroduction FOR YOUR SAFETYREAD THIS BEFORE OPERATING YOUR UNIT ENGLISHUniversal Remote Controls CONTENTSOSD Menu Settings Troubleshooting Guide SpecificationsSystem Connections 1. CONNECTING ANTENNAsENGLISH ENGLISH 2. CONNECTING VIDEO COMPONENTSContinued ENGLISH4. CONNECTING EXTERNAL INs 3. CONNECTING AUDIO COMPONENTS5. CONNECTING DIGITAL INs and OUT ENGLISH8. CONNECTING SPEAKERS 6. CONNECTING SYSTEM CONTROL7. SUBWOOFER PREOUT connection Surround back speakersFront left and right speakers and center speaker Speaker placementSurround left and right speakers Surround back left and right speakers10. CONNECTING ROOM 2 OUTs 9. CONNECTING DC TRIGGER OUTENGLISH 12. CONNECTING PC FOR UPGRADES 11. CONNECTING MULTI-ROOMSYSTEM KIT13. SWITCHED AC OUTLETs 14. AC INPUT CORDFLUORESCENT DISPLAY Front Panel ControlsENGLISH AUX IN JACK SETUP MIC JACKVIDEO 4 IN JACKS ENGLISHDigi link system remote controls Universal Remote ControlsENGLISH ENGLISH FUNCTION TABLE of the NUMBERED BUTTONSOPERATING COMPONENTS WITH REMOTE CONTROL REMOTE CONTROL OPERATION RANGELOADING BATTERIES ENGLISHEntering a setup code USING FUNCTIONS OF REMOTE CONTROLENGLISH ENGLISH Using a punch-throughfunctionOperating a macro function Programming a macro functionENGLISH LISTENING TO A PROGRAM SOURCE OperationsBefore operation ENGLISHListening with headphones When CD, VIDEO 1~3 is selected as an input sourceMuting the sound ENGLISHSurround modes SURROUND SOUNDDTS Digital Surround DTS - ES Extended SurroundDolby Pro Logic Dolby Pro Logic IIx surroundDolby Headphone Dolby Pro Logic II surroundENGLISH ENJOYING SURROUND SOUNDTo cancel the surround mode for stereo operation Adjusting each channel level with test toneListening in a Dolby Headphone mode 2CH downmix modeENGLISH Adjusting the current channel levelRecalling the memorized channel levels Memorizing the adjusted channel levelsENGLISH Manual tuning Auto tuningLISTENING TO RADIO BROADCASTS ENGLISHTuning to preset stations Presetting radio stationsScanning preset stations in sequence MEMORY BACKUP FUNCTIONRECORDING Dubbing the audio and video signalsRecording with TAPE Dubbing from video components ontoENGLISH DIGITAL AUDIO RECORDING WITH MD RECORDEROTHER FUNCTIONS Operating the sleep timerENGLISH Adjust the ROOM 2 volume ROOM 2 SOURCE PLAYBACKENGLISH ENGLISH OSD Menu SettingsWhen selecting the INPUT SETUP When selecting the SYSTEM SETUPWhen selecting the SOUND PARAMETER When selecting the ROOM 2 SETUPWhen selecting the AMP ASSIGN SETTING THE SYSTEM SETUPWhen selecting the OUT ASSIGN ENGLISHWhen selecting the TONE CONTROL When selecting the SUBWOOFER MODEENGLISH When selecting the MOMENTARY OSD When selecting the CINEMA EQWhen selecting the OSD POSITION ADJUST ENGLISHWhen selecting the items other than NAME SETTING THE INPUT SETUPWhen selecting the DIGITAL AUDIO ENGLISHWhen selecting the AUTO SURROUND When selecting the VIDEO MODEWhen selecting the REMASTER When selecting the AV SYNCENGLISH When selecting the NAMEWhen selecting the AUTO SETUP SETTING THE SPEAKER / ROOM EQ SETUPENGLISH 2 ENTER button ENGLISHPress the CURSOR UP /DOWN buttons to select the START, then press the ENTERENGLISH When selecting the SPEAKER CONFIGURATIONENGLISH About the speaker sizeAbout the speaker distance When selecting the SPEAKER DISTANCEENGLISH About the crossover frequency When selecting the SPEAKER X-OVERENGLISH ENGLISH When selecting the ROOM EQAdjusting the current channel level SETTING THE CH LEVEL SETUPENGLISH Memorizing the adjusted channel levels Recalling the memorized channel levelsENGLISH When selecting the NIGHT MODE SETTING THE SOUND PARAMETERENGLISH When selecting the PANORAMA mode When selecting the DOLBY PLII MUSICWhen selecting the DIMENSION control ENGLISHENGLISH When selecting the DOLBY HEADPHONEENGLISH When selecting the DOLBY VIRTUALWhen selecting the ROOM SETTING THE ROOM 2 SETUPWhen selecting the INPUT When selecting the VOLUMEPROBLEM Troubleshooting GuideENGLISH POSSIBLE CAUSEENGLISH SpecificationsENGLISH Setup Code TableENGLISH Headquarter ENGLISHENGLISH AUX-LD AUX-TAPE/MDAUX-TAPE AUX-AMPAUX-HOMEAUTOMATION AUX-ACCESSARYAUX-DBS ENGLISH