Rotel RSX-1057 owner manual Test Tone, Delay Setup, Calibration with an SPL meter

Page 43

Test Tone

TEST TONE

LEFT:+ 1dB

CENTER:- 1dB

RIGHT:+ 2dB

R SURROUND:+ 5dB

R CTR BACK:+ 2dB

L CTR BACK:+ 2dB

L SURROUND:+ 4dB

SUBWOOFER:+ 9dB

MAIN MENU

This menu uses filtered pink noise test tones to set equal volume levels for all speakers (left front, center, right front, right surround, center back, left surround, and subwoofer) to ensure proper surround sound reproduction. Setting the output levels using the test proce- dure provides the most accurate adjustment so that digital surround sound material will be reproduced as it was intended and is a critical step in calibrating the system.

NOTE: If you have configured your system to use two center back speakers, there will be an additional line in the menu, giving you the ability to independently adjust the CENTER BACK 1 and CENTER BACK 2 speakers.

To access this menu and perform the test tone calibration, you can be in any surround mode except BYPASS with any input except the MULTI INPUT. Enter the OSD menu sys- tem and select TEST TONE from the MAIN MENU to reach this screen.

When you enter the TEST TONE menu, you will hear a test tone coming from the high- lighted speaker. Highlight different speakers by moving the cursor to the desired line using the UP/DOWN buttons. The test tone will shift accordingly to the selected speaker.

Seated in the normal listening location, shift the test tone to the various speakers. Using the one speaker as a reference, listen for any speakers that are noticeably louder or qui- eter. If so, adjust that speaker’s levels up or down (in 1dB increments) using the +/– but- tons. Continue switching among the speak- ers and adjusting until all speakers are the same volume.

To return to the MAIN menu, press the EN- TER button. Press the MENU/OSD button on the remote to cancel the menu display and return to normal operation.

43

Calibration with an SPL meter:

Calibrating the system with an SPL meter, rather than by ear, provides more precise results and improves the system’s perfor- mance significantly. Inexpensive SPL meters are widely available and the procedure is quick and easy.

Both Dolby and DTS specify a standard cal- ibration level for all theaters to ensure that soundtracks can be played at the volume level intended by the director of the film. This ref- erence level should result in spoken dialog played at a realistic level for normal speech with the loudest peaks in any single channel at about 105dB. The RSX-1057’s test tones are generated at a precise level (-30dBFs) relative to the loudest possible digitally re- corded sound. At the Dolby or DTS reference level, these test tones should produce a 75dB reading on an SPL meter.

Set the meter to its 70dB dial setting with SLOW response and C-weighting, held away from your body at your listening position (mount- ing the SPL meter on a camera tripod makes this easier). You can point the SPL meter at each speaker as it is being measured; how- ever, positioning the meter in a fixed position pointing at the ceiling is easier and probably produces more consistent results.

Increase the master volume control on the RSX-1057 until the meter reads 75dB (+5dB on the meter scale) when playing the test tone through one of the front speakers. Then, use the individual channel adjustments on the TEST TONE menu to adjust each of the indi- vidual speakers, including the subwoofer, to the same 75dB on the SPL meter.

NOTE: Due to meter weighting curves and room effects, the actual level of the subwoofer may be slightly higher than you measure. To compensate, Dolby suggests setting the sub- woofer several dB lower when calibrating with an SPL meter (i.e. set the subwoofer to read 72dB on the meter instead of 75dB). Ultimately, the proper subwoofer level must be determined by personal taste and some listeners prefer to set it above 75dB for film soundtracks. Exaggerated bass effects come at the expense of proper blending with the main speakers and place stress on the sub- woofer and its amplifier. If you can localize bass from the subwoofer, the subwoofer level may be too high. Music can be useful for fine-tuning the subwoofer level as excessive

English

bass is readily apparent. The proper setting will generally work well for music and movie soundtracks.

Remember the setting of the master volume control used during this calibration. To play a Dolby Digital or DTS soundtrack at the ref- erence volume level, simply return to that vol- ume setting. Note that most home theater lis- teners find this setting to be excessively loud. Let your own ears be the judge for deciding how loud to playback movie soundtracks and adjust the master volume control according- ly. Regardless of your listening levels, using an SPL meter to calibrate equal levels for all speakers in the system is recommended.

Delay Setup

DELAY SETUP

LEFT: 12ft 3.6m

CENTER: 11ft 3.3m

RIGHT: 11ft 3.3m

R SURROUND: 6ft 1.8m

R CTR BACK: 8ft 2.4m

L CTR BACK: 9ft 2.7m

L SURROUND: 5ft 1.5m

SUBWOOFER: 5ft 1.5m

MAIN MENU

The DELAY SETUP menu, which is reached from the MAIN menu, allows you to set the delay for individual speakers. This ensures that the sound from each speaker arrives si- multaneously at the listening position, even when the speakers are not all placed at equal distances from the listener. Increase the delay to speakers located closer to the seating area and decrease the delay to speakers located farther from the seating area.

The RSX-1057 makes setting the delay time for each speaker very easy. Simply measure the distance (in feet or meters) from your seating position to each speaker in your system. Set the measured distance in the line for each speaker. The menu provides a line for each speaker configured in your system and pro- vides a range of settings up to 99 feet (30 meters) in 1 foot (0.3 m) increments with each increment equivalent to an additional delay of 1ms.

To change a setting, place the highlight on the desired line using the UP/DOWN but- tons and use the +/– buttons to increase or decrease the delay setting. To return to the MAIN menu, press the ENTER button. Press the MENU/OSD button on the remote to cancel the display and return to normal operation.

Page 42 Page 44
Image 43
Page 42 Page 44
Contents RSX-1057 10 cm Cm 4 FCC Information Important Safety InstructionsControls and Connections RR-1060 Remote EnglishConnecting the Speakers Digital Video Connections TV Analog Connections DVD Player Analog Connections English Monitor OUT Hdmi VCR Analog Connections CD Player/CDR Recorder ConnectionsAM and FM Antennae Connections Audio Recorder ConnectionsOn-Screen Menus Contents Specifications Menu BasicsAbout Rotel Key FeaturesGetting Started Tape Inputs PlacementUnpacking CD InputsSpeaker Outputs Video 1-5 Audio InputsVideo 1-3 Audio Outputs Multi InputsVideo 1-3 S-Video Outputs Composite Video InputsComposite Video Outputs Video 1-5 S-Video InputsOther Connections Digital Audio Input & OutputsCable, Satellite, Hdtv Tuner REM in JacksComputer I/O CD PlayerTV Monitor Audio RecorderVCR or Digital Video Recorder DVD-A or Sacd PlayerAmplifiers Connecting a SubwooferRedirect Feature SpeakersFront Panel Overview RSX-1057REC Buttons Volume Knob Volume ButtonUsing the RR-1060 Audio Button Standby Button Power ButtonBasic Operations Selecting Inputs DTS DTS 96/24 Overview Surround FormatsDolby Surround Dolby Pro Logic Dolby DigitalDolby Pro Logic 7.1 Channel Surround DTS Neo6Dolby Digital Surround EX 7.1 Channel SurroundOther Digital Formats Manually Selecting Surround ModesDolby Digital 2.0 discs Dolby Digital 5.1 discs Dolby Digital Surround EX discsOn a 6.1/7.1 system with a DTS DTS 5.1 discs DTS 96/24 discs DTS-ES 6.1 discsMpeg Multichannel discs Digital Stereo discs PCM, MP3, and HdcdSpeaker Level Other SettingsGroup Delay Analog StereoTuner Controls Contour/Tone SettingsTo adjust dynamic range To adjust the contour settings from the remoteMemory Button Numeric Buttons Station PresetsTA Button Disp ButtonPTY Button TP ButtonControlling Zone 2 from the Remote Location Zone 2 Power On/OffZone 2 Operation Controlling Zone 2 from the Main RoomMain Menu Menu BasicsNavigation Buttons System StatusConfiguring Inputs Input SetupMulti Input Multi Input SetupUnderstanding Speaker Con- figuration ConfiguringAdvance Speaker Setup Speaker SetupSubwoofer Setup Subwoofer SetupTest Tone Delay SetupCalibration with an SPL meter Other Options Contour SetupDefault Setup Zone 2 SetupTroubleshooting Specifications Rotel Europe Rotel of AmericaRotel Deutschland

RSX-1057 specifications

The Rotel RSX-1057 is a robust and versatile AV receiver that has garnered attention for its excellent performance and range of features. Designed to meet the demands of home theater enthusiasts, it stands out for its combination of advanced technology, superior audio quality, and user-friendliness.

One of the key features of the RSX-1057 is its robust amplification capabilities. With a power output of 75 watts per channel, it can deliver rich sound across multiple audio channels, making it ideal for multi-channel audio setups. This is complemented by the receiver's high-current design, which ensures dynamic sound reproduction with minimal distortion, even at high volumes.

The receiver supports a wide range of audio formats, including Dolby Digital, Dolby Pro Logic II, DTS, and various music-enhancing technologies. This allows users to experience movies and music in immersive detail, making it a great choice for both film buffs and music lovers alike. The RSX-1057 also features an integrated AM/FM tuner, enabling users to enjoy their favorite radio stations without the need for additional equipment.

In terms of connectivity, the RSX-1057 boasts an impressive selection of input and output options. It includes several HDMI inputs, component video inputs, and composite video connections, making it highly compatible with a variety of devices, from Blu-ray players to gaming consoles. Furthermore, the receiver offers audio outputs that allow for easy integration with subwoofers, enhancing the overall audio experience.

One of the standout technologies in the RSX-1057 is its proprietary ‘Rotel Link’ feature, which enables multi-room audio setups. This function allows users to connect multiple components and create a unified audio system throughout their home. The intuitive remote control enhances the user experience, providing seamless access to browsing and selecting different inputs and settings.

The design of the Rotel RSX-1057 is both aesthetically pleasing and functional. Its sleek chassis features a brushed aluminum front panel, which not only looks great but also minimizes environmental interference. Furthermore, the unit is designed for efficient heat dissipation, ensuring longevity and reliable performance over time.

Overall, the Rotel RSX-1057 is a well-rounded AV receiver that excels in audio fidelity, versatility, and user-centric features. Its commitment to quality and innovation makes it a popular choice for anyone seeking to elevate their home entertainment experience.
Top Page Image Contents