GE 49-8723 Lift-Off Oven Door, Oven Heating Elements, Inside of the door, Outside of the door

Page 32

CARE AND CLEANING

(continued)

Lift-Off Oven Door

The oven door is removable, but it is heavy. You may need help removing and replacing the door. Do not lift the door by the handle. This can cause the glass to break or can cause damage to the door.

To remove the door, open it a few inches to the special stop position that will hold the door open. Grasp firmly on each side and lift the door straight up and off the hinges.

NOTE: Be careful not to place hands between the hinge and the oven door frame as the hinge could snap back and pinch fingers.

To replace the door, make sure the hinges are in the special stop position. Position the slots in the bottom of the door squarely over the hinges. Then lower the door slowly and evenly over both hinges at the same time. If hinges snap back against the oven frame, pull them back out. If the oven door is crooked, push down on the high corner to straighten it.

TO CLEAN THE DOOR:

Inside of the door:

•Because the area inside the gasket is cleaned during the self clean cycle, you do not need to clean this by hand. Any soap left on the liner causes additional stains when the oven is heated.

•The area outside the gasket can be cleaned with a scouring pad.

•Do not rub or clean the door gasket—the fiberglass material of the gasket has an extremely low resistance to abrasion. An intact and well-fitting oven door gasket is essential for energy-efficient oven operation and good baking results. If you notice the gasket becoming worn, frayed or damaged in any way or if it has become displaced on the door, you should have it replaced.

NOTE: The gasket is designed with a gap at the bottom to allow for proper air circulation.

Inside Gasket

Gasket

Outside Gasket

Outside of the door:

•Use soap and water to thoroughly clean the top, sides and front of the oven door. Rinse well. You may also use a glass cleaner to clean the glass on the outside of the door. To avoid water marks on the inside of the door glass, do not let water drip into the vent opening.

•Spillage of marinades, fruit juices, tomato sauces and basting materials containing acids may cause discoloration and should be wiped up immediately. When surface is cool, clean and rinse.

•Do not use oven cleaners, cleansing powders or harsh abrasives on the outside of the door.

Oven Heating Elements

Do not clean the bake element or the broil element.

Any soil will burn off when the elements are heated.

The bake element can be lifted gently to clean the oven floor. If spillovers, residue or ash accumulate around the bake element gently wipe around the element with warm water.

Broil Element

Bake Element

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents UseandCare& Installation Guide Before using your range, read this guide carefully Save time and money Before you request service…Help US Help YOU… Write down the model and serial numbersImportant Safety Instructions Important Safety InstructionsSelf-Cleaning Oven OvenSave These Instructions Cooktop and Radiant Surface UnitsFeatures of Your Range 18 JBP75 JBP76 JBP77 19 JBP78Features of Your Range HOW does this Cooktop Compare To Your OLD ONE? Type of Cooktop Description How it Works RadiantHot Surface Indicator Light CooktopComparison General Information About Radiant Surface UnitsHow to Set the Controls Cooking Guide for Using Heat SettingsSurface unit on indicator light will glow Surface ControlsSurface Cookware Tips Surface ControlsSurface Cookware Tips Types of CookwareHow to Check Pan Performance Special Cautions for Glass CooktopsHome Canning Tips SurfaceCookware Tips Home Canning TipsGlass Cooktop Cleaning Glass Cooktop CleaningFor normal, light soil For heavy, burned on soilGlass Features of Your Oven ControlCleaning Features of Your Oven Control Oven CONTROL, Clock and Timer Using Your Oven Oven Control, Clock and Timer Using Your OvenHow to Set Your Range for Baking BakingPreheating Baking PansBaking Timed Baking How to Time BakeHow to Set Immediate Start and Automatic Stop Timed Baking How to Set Delay Start and Automatic StopQuestions and Answers Adjust the Oven Thermostat Do IT YourselfAdjust the Oven RoastingThermostat RoastingFrozen Roasts Why is my roast crumbling when I try to carve it?Roasting Guide Broiling BroilingGuide Broiling Guide Beef SteaksOperating the SELF-CLEANING Oven Self-Cleaning OvenBefore a Clean Cycle Broiling GuideAfter a Clean Cycle How to Set the Oven for CleaningTo Stop a Clean Cycle Operating the Self Cleaning OvenHow to Set Delay Start of Cleaning on some models Care and Cleaning Oven Light Replacement on some modelsTo remove To replace coverControl Panel and Knobs Oven VentMetal Parts Painted SurfacesDo not clean the bake element or the broil element Lift-Off Oven DoorOven Heating Elements Inside of the doorCare and Cleaning Broiler Pan and GridInstallation Instructions Before YOU BeginStep Step Wire Power Cord Installation Step Wire Conduit Installation Step Final Check QUESTIONS? USE this Problem Solver Installation Instructions Problem SolverProblem Solver Oven will not WorkOven will not If YOU Need SERVICE… If You Need Service We’ll Be ThereWarranty

4164D2966P234, 49-8723 specifications

The GE 49-8723,4164D2966P234 is a cutting-edge component designed to meet the demands of modern industrial applications. This part, part of General Electric's extensive lineup, is engineered with advanced technologies and high-performance characteristics that make it a preferred choice in various sectors including manufacturing, energy, and automation.

One of the standout features of the GE 49-8723 is its enhanced reliability. Built with robust materials and sophisticated engineering processes, this component is designed to withstand harsh operating conditions, ensuring minimal downtime and maintenance costs. This reliability is crucial for industries that rely on continuous operation and efficiency.

The technology behind the GE 49-8723 incorporates intelligent sensors that provide real-time data monitoring. These sensors contribute to improved operational visibility, enabling proactive management of systems. By integrating data analytics capabilities, users can track performance metrics and optimize usage, leading to increased productivity and reduced energy consumption.

Another significant aspect of the GE 49-8723 is its compatibility with various control systems. It supports multiple communication protocols, which allows seamless integration into existing infrastructures. This flexibility is essential for manufacturers looking to upgrade their systems without incurring substantial costs or complexities associated with retrofitting.

In addition to its compatibility, the GE 49-8723 offers advanced safety features to protect both the equipment and personnel. It includes built-in fail-safes and redundancy measures that ensure consistent operation even in the event of component failure. This emphasis on safety not only protects investments but also enhances overall workplace safety.

The compact design of the GE 49-8723 also deserves mention. Its smaller footprint allows for easier installation and greater versatility in application, making it suitable for environments with limited space. Despite its size, it does not compromise functionality and performance, making it an ideal choice for various applications.

Overall, the GE 49-8723,4164D2966P234 showcases a balanced combination of reliability, advanced technology, safety, and adaptability. Its innovative design and integration capabilities provide industries with the tools needed to enhance operational efficiency and sustainability, making it a valuable asset in the ever-evolving landscape of industrial applications.
Top Page Image Contents