Leupold PS536GS manual III. Assembly, Top Panel and Base Pad Assembly

Page 9

III. ASSEMBLY

A.Top Panel and Base Pad Assembly

SECTION 2 - INSTALLATION

Figure 2-3 - Leg extension and casters installation

1. Install the four leg extensions onto the base pad using the

 

3/8"-16x1" screws, 3/8" flat washers, and 3/8" lockwashers

 

supplied in the Base Pad Kit. See Figure 2-3. Check that

 

the finished sides of each leg extension face OUTWARDS.

 

For domestic and standard export ovens:

 

One rear leg should be attached using three 3/8"-16 x 1"

 

screws and the 3/4" eyebolt, as shown in Figure 2-3. This

 

eyebolt acts as the anchor point for the restraint cable

 

assembly (see Part C, Restraint Cable Installation).

2. If your oven is equipped with the lower shelf, position it in

 

place as shown in Figure 2-3. Check that the lip on the shelf

 

faces DOWN. Seal joint between leg and shelf with NSF

 

listed silicone.

3. For domestic and standard export ovens:

 

Install one caster onto each leg extension, as shown in

 

Figure 2-4. Use the 3/8"-16x1" screws, 3/8" flat washers,

 

and 3/8" lockwashers supplied in the Installation Kit. The

 

locking casters should be installed at the FRONT of the

 

oven. The non-locking casters should be installed at the

 

REAR of the oven.

 

For CE export ovens:

 

The Installation Kit includes four casters AND four 152mm

 

adjustable legs. The casters are provided to allow the oven

 

to be more easily moved to the installation location, and are

 

NOT suitable for use as part of the oven installation. Refer

 

to the notice at the beginning of this Section.

 

After the oven is at the installation location, install one

 

152mm adjustable leg into the center hole on the bottom

 

of each leg extension, as shown in Figure 2-4.

4.

Install the lower oven cavity onto the base pad. See Fig. 2-4.

5.

For single ovens ONLY, install the top panel using the

Finished sides of

leg extension face corner of base pad

CE ovens do not use the eyebolt.

Lower

shelf

CE-approved

ovens:

152mm adjustable leg MUST be used for installation

3/8" flat

washer

3/8" lock

washer

3/8"-16 x 1" hex screw

3/4" eyebolt (inside corner of one rear leg extension only)

Domestic and

standard export

ovens:

Locking casters -

FRONT of oven

Non-locking casters -

REAR of oven

3/8" flat

washer

3/8" lock

washer

3/8"-16 x 1"

hex screw

ENGLISH

screws included in the base pad kit, as shown in Figure 2-

5. Then, skip ahead to Part C, Restraint Cable Installation.

For double or triple ovens, continue on to Part B, Stacking. Note that the top panel should NOT be installed for double

Figure 2-5 - Top panel installation

NOTE: DO NOT install top panel onto double or triple ovens until AFTER stacking the oven cavities. See Part B, Stacking.

#10 x 2"

and triple ovens until after stacking the oven cavities.

screws

Top

Figure 2-4 - Base pad installation

Bottom oven

cavity

Assembled

base pad

panel

9

Image 9
Contents PS536GS Gas Ovens English For Your SafetyTable of Contents III. Oven Specifications Oven UsesConveyor Drive Motor Moves the conveyor Electrical specifications for gas ovens per oven cavity Installation Installation KIT see Figure Requirements II. Ventilation SystemRecommendations Other ventilation concernsTop Panel and Base Pad Assembly III. AssemblyStacking Restraint Cable Installation10 Conveyor placement Conveyor Installation12 Conveyor and master link orientation Final AssemblyIV. Electrical Supply Additional Information Gas OvensConnection GAS Supply During Pressure Testing Note the FollowingGas Conversion OvenEnglish Not Shown Location and Description of ControlsDaily Startup Procedure Daily Shutdown ProcedureII. Normal Operation STEP-BY-STEP SP Lock III. Quick Reference Digital Temperature ControllerOvertemp Heat onMaintenance Daily MaintenanceIII. Maintenance Every 3 Months II. Maintenance MonthlySplit Belt Disassembly and Cleaning Top Row T1 T2 T3 T4English IV. Maintenance Every 6 Months Blower BeltLubricating the Blower Fan Bearings QTY Description KEY Spare Parts KITEnglish II. Installation KIT QTYSingleoven Doubleoven Deutsch Français IIIa. PANELS, END Plugs Without Window III. PANELS, END Plugs and WindowEnglish IV. Control Compartment English Not Shown Machinery Compartment and GAS TrainEnglish Item QTY Description VI. Rear Compartment and BlowersEnglish Item QTY Conveyor Description VII. SINGLE-BELT ConveyorsEnglish VIII. SPLIT-BELT Conveyors English English Deutsch English English Deutsch English Español Français Deutsch Hour Service Hotline