Leupold PS536GS manual English

Page 21

SECTION 4 - MAINTENANCE

2.

Remove the master links from each conveyor belt.

 

Then, roll the belts up along the length of the conveyor

 

to remove them from the frame.

3.

Remove the two conveyor adjustment screws from the

 

idler end of the conveyor frame, as shown in Figure 4-

 

4.

4.

Remove the idler shaft assembly from the conveyor.

5.

Pull apart the two sections of the idler shaft.

6.

Clean the shafts thoroughly using a rag. Then, lubri-

 

cate both the extended shaft and the interior of the

 

hollow shaft using a light food-grade lubricant. DO

 

NOT lubricate the shafts using WD40 or a similar

 

product. This can cause the shafts to wear rapidly.

7.

Before reassembling the shafts into the conveyor

 

frame, check that they are oriented properly.

Figure 4-4 - Disassembling the idler shaft

 

Disassemble,

 

 

clean, and

ENGLISH

 

lubricate shafts

Bronze

 

washer

8. Reassemble the idler shaft into the conveyor. Make

sure that the bronze washer is in place between the

two sections of the shaft. See Figure 4-4.

Remove

Remove

idler shaft assembly

9. Replace the conveyor adjustment screws as shown in

 

Figure 4-4. To allow the conveyor belt to be reinstalled

 

later, do not tighten the screws at this time.

10.

Loosen the set screw on both of the conveyor drive

 

sprockets. Then, remove the sprockets from the shaft.

11.

Check the conveyor configuration as follows:

 

High-speed conveyors are equipped with large

 

 

flange bearings at both ends of the shaft, as

 

 

shown in Figure 4-5. For these conveyors, re-

 

 

move the two screws that hold each bearing to the

 

 

conveyor frame. With the screws removed, lift the

 

 

end of the shaft at the front of the oven, and pull the

 

 

entire assembly free of the conveyor frame.

 

Standard conveyors are equipped with bronze

 

 

bushings mounted on spacers at both ends of the

 

 

shaft, as shown in Figure 4-5. For these convey-

 

 

ors, remove the two screws that hold the bracket

 

 

to the conveyor frame. With the screws removed,

 

 

lift the end of the shaft at the front of the oven, and

 

 

pull the entire assembly free of the conveyor

 

 

frame. The brackets will be removed along with

 

 

the drive shaft assembly.

12.

Disassemble and lubricate the two sections of the

 

drive shaft as described for the idler shaft, above.

13.

Before reassembling the shafts into the conveyor

 

frame, check that they are oriented properly.

14.

Reassemble the drive shaft into the conveyor. Make

 

sure that the bronze washer is in place between the

 

two sections of the shaft. See Figure 4-6.

15.

Replace the drive sprockets. Reassemble the belts

 

and master links onto the conveyor.

16.

Reinstall the end plugs and conveyor onto the oven.

17.

Reattach the drive chains. Replace the chain cover.

18Check the tension of the conveyor belt as shown in Figure 2-11 (in Section 2, Installation). The belt should lift about 1" (25mm). If necessary, adjust the belt tension by turning the conveyor adjustment screws.

19. Replace all components onto the oven.

adjustment

screws

Figure 4-5 - Drive shaft configurations

Flange bearing

Bronze bushing with

(used with high-

spacer (used with

speed conveyors)

standard conveyors)

Figure 4-6 - Disassembling the drive shaft

Disassemble,

clean, and

lubricate shafts

Flange bearing

shown (used with

high-speed conveyors)

Loosen set screws and remove drive sprockets

Remove 2 screws and nuts per side to free bearings/brackets

21

Image 21
Contents PS536GS Gas Ovens English For Your SafetyTable of Contents III. Oven Specifications Oven UsesConveyor Drive Motor Moves the conveyor Electrical specifications for gas ovens per oven cavity Installation Installation KIT see Figure Requirements II. Ventilation SystemRecommendations Other ventilation concernsTop Panel and Base Pad Assembly III. AssemblyStacking Restraint Cable Installation10 Conveyor placement Conveyor Installation12 Conveyor and master link orientation Final AssemblyIV. Electrical Supply Additional Information Gas OvensConnection GAS Supply During Pressure Testing Note the FollowingGas Conversion OvenEnglish Not Shown Location and Description of ControlsDaily Startup Procedure Daily Shutdown ProcedureII. Normal Operation STEP-BY-STEP SP Lock III. Quick Reference Digital Temperature ControllerOvertemp Heat onMaintenance Daily MaintenanceIII. Maintenance Every 3 Months II. Maintenance MonthlySplit Belt Disassembly and Cleaning Top Row T1 T2 T3 T4English IV. Maintenance Every 6 Months Blower BeltLubricating the Blower Fan Bearings QTY Description KEY Spare Parts KITEnglish II. Installation KIT QTYSingleoven Doubleoven Deutsch Français IIIa. PANELS, END Plugs Without Window III. PANELS, END Plugs and WindowEnglish IV. Control Compartment English Not Shown Machinery Compartment and GAS TrainEnglish Item QTY Description VI. Rear Compartment and BlowersEnglish Item QTY Conveyor Description VII. SINGLE-BELT ConveyorsEnglish VIII. SPLIT-BELT Conveyors English English Deutsch English English Deutsch English Español Français Deutsch Hour Service Hotline