Vanguard Heating SDVBN(A), SDVBP(A) manual Installing Remote Receiver

Page 22

® SDVBN(A) AND SDVBP(A)

CAST IRON STOVE AND BURNER SYSTEM

STOVE AND

DIRECT-VENT BURNER SYSTEM INSTALLATION

Continued

INSTALLING OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIES - GHRC AND GHRCT SERIES

Installing Remote Receiver

1.Open bottom door on stove body and locate the switch plate on the left of the valve bracket.

2.Unscrew switch plate (see Figure 47).

3.Disconnect wires from THTP and TH on control valve that lead to the switch (see Figure 44, page 21). Discard switch plate, screws, and nuts.

4.Install battery into receiver battery clip and connect to terminals (see Figure 48).

5.Place receiver into valve bracket and align holes (see Figure 49).

6.Use push-in fasteners included with receiver to secure to bracket.

7.Connect the wires from the receiver to the valve at TH and THTP (see Figure 44, page 21).

LO

H

I

OFF

L

 

P

 

I

ON

O

T

Figure 47 - Removing Switch Plate

Receiver

Terminal

Wires

Battery

Clip

9-Volt Battery

Figure 48 - Installing Battery in Receiver

LO

H

I

OFF

I

 

P

 

L

ON

O

T

Figure 49 - Installing Remote Receiver

Installing 9-Volt Battery in Hand- Held Remote Control Unit

1.Remove battery cover on back of re- mote control unit

2.Attach terminal wires to a 9-volt bat- tery (not included). Place battery into the battery housing.

3.Replace battery cover onto remote con- trol unit.

 

Battery

Remote

 

Control Unit

Terminal

Cover

 

 

 

Wires

 

 

9-Volt

 

 

Battery

 

 

Battery Housing

Figure 50 - Installing Battery in Hand- Held Remote Control Unit

REMOVING/REPLACING GLASS DOOR

You must remove glass door to install logs, lava rock, and ember material. To remove glass door, you must first remove the front panel on stove body.

CAUTION: Do not operate this burner system with a broken glass door panel or without the glass door panel securely in place. For replacement part in- formation see Replacement Parts, page 31.

1.Remove 2 bolts from bottom of stove and one from the top of stove to remove front panel (see Figure 51).

22

2.Remove the screws from the 2 tabs at the top of the glass door while holding door securely keeping it from falling forward (see Figure 52).

3.Grasp door by both sides and ease it upward off of the lower bracket (see Figure 52).

4.To replace glass door, follow the above instructions in reverse.

Bolt

Bolt

Stove Front Panel

Figure 51 - Removing Front Panel from Stove

Screw

Glass

Door

Figure 52 - Removing Glass Door from Burner System

105499

Page 21 Page 23
Image 22
Page 21 Page 23
Contents For Your Safety For Your Safety What to do if YOU Smell GASSafety Information Sdvbna and Sdvbpa Cast Iron Stove and Burner SystemLocal Codes Product FeaturesProduct Identification Glossary TermsPRE-INSTALLATION Preparation Location and Space RequirementsStove Body Assembly Lift off corrugated box enclosing stove body cratingCast Iron Stove and DIRECT-VENT Burner System Assembly Installing DIRECT-VENT Burner System Into Stove BodyInstalling Optional Blower Accessory Installing GA3700/DA3610T BlowersGeneral Venting Installing Rear CoverLocation of Vent Termination General Venting Installation Planning Venting InstallationInstallation Precautions Installing Vent System in a ChaseInstallation for Horizontal Termination Snorkel TerminationVent Pipe Connections Horizontal Termination Configurations Horizontal VentingInstallation for Vertical Termination Flat Ceiling InstallationCathedral Ceiling Installation If area above is a room, install firestop above framed holeVertical Termination Configurations Vertical Rigid Venting Configuration Using One 90 ElbowParts Lists for Venting Kits and Components High Altitude InstallationVanguard Rigid Venting Installation Items Needed Stove DIRECT-VENT Burner System InstallationInstalling GAS Piping to STOVE/BURNER System Location Check GAS TypePressure Testing Gas Supply Piping System Connecting Stove Burner System to GAS SupplyChecking GAS Connections Pressure Testing Burner System Gas ConnectionsInstalling Optional Wall Mount Switch GWMS2 Installing Optional Wall Mounted Thermostat GWMT1Installing Remote Receiver Receiver Terminal Wires Battery Clip Volt BatteryInstalling LOGS, Lava Rock and Glowing Embers Installing Log NoOperating Stove with Burner System For Your Safety Read Before LightingManual Lighting Procedure Lighting InstructionsGhrc Series Operation Optional Remote OperationThermostat Control Operation Ghrct Series OperationInspecting Burners Operating Optional Blower AccessoryPilot Assembly Operating Optional GWMT1 Wall Mounted ThermostatPilot and Burners Cleaning and MaintenanceGlass Door LogsTroubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Gas leak. See Warning statement Wiring Diagram Replacement PartsTechnical Service Service HintsSpecifications Sdvbna SdvbpaAccessories Illustrated Parts Breakdown Sdvbna SdvbpaParts List KEY Part Number Description QTYAmity SCIVF* Series PSCIVF* Series Indicates Color Suffix DesignationKEY Part Description QTY Warranty Information

SDVBP(A), SDVBN(A) specifications

Vanguard Heating SDVBN(A) and SDVBP(A) are innovative heating solutions designed for residential and commercial applications, aiming to deliver unparalleled efficiency and comfort. These models showcase advanced technologies tailored to meet modern heating demands while ensuring minimal environmental impact.

One of the standout features of the Vanguard Heating SDVBN(A) and SDVBP(A) is their highly efficient heating performance. Operating with an Annual Fuel Utilization Efficiency (AFUE) rating of up to 95%, these models convert a significant portion of fuel into heat, minimizing energy waste and lowering utility costs. This efficiency translates to substantial savings for homeowners and businesses alike, making them an economically sound choice in the long run.

The SDVBN(A) and SDVBP(A) are equipped with variable-speed blower motors, allowing for precise control of airflow. This technology not only enhances comfort by maintaining consistent temperature levels throughout spaces but also contributes to reduced noise levels during operation. The quiet performance of these units is particularly appealing for residential settings, such as bedrooms and living areas.

In terms of versatility, Vanguard offers multiple configurations, allowing installers to tailor the heating system to specific requirements. Whether it’s a large open plan or a more segmented layout, the adjustable airflow and zoned heating capabilities ensure that every corner of the space is adequately warmed.

Another notable characteristic is the integrated smart technology. Both models come with advanced control systems that can be easily connected to compatible smart thermostats. This allows users to monitor and adjust heating settings remotely, providing added convenience and optimizing energy usage according to individual schedules.

Moreover, the SDVBN(A) and SDVBP(A) feature robust construction designed for durability. With high-quality materials and components, these units can withstand the rigors of daily use, ensuring reliable performance throughout their lifespan. Regular maintenance is simplified due to accessible design, empowering users or service technicians to conduct routine checks and repairs with ease.

Vanguard Heating has also incorporated safety features, including built-in sensors that monitor system performance and automatically shut down the unit in case of any malfunctions. This proactive approach provides peace of mind, knowing that the heating system is both efficient and safe.

In summary, Vanguard Heating SDVBN(A) and SDVBP(A) models embody cutting-edge technology, efficiency, and reliability in home and commercial heating solutions. Their ability to deliver comfortable, quiet, and economical heating while prioritizing safety and ease of maintenance makes them an excellent choice for any heating application.
Top Page Image Contents