VXI SM7100 Interrupt Control Register 0x1C Read and Write, Subclass Register 0x1E Read Only

Page 25

www.vxitech.com

Interrupt Control Register (0x1C) — Read and Write

D15

Scan Function done

0

= enabled

mask bit

1

= disabled

 

D14

Openbus Active Event

0

= enabled

true mask bit

1

= disabled

 

D13-D9

Unused

Data written to these bits has no effect

D8

Module Busy Complete

0

= enabled

1

= disabled

 

 

D7

IR ENA*

0

= writing a 0 to this bit enables interrupter capabilities

1

= writing a 1 to this bit disables interrupter capabilities

 

 

D6

IH ENA*

The module has no interrupt handler capability; therefore writing a 1 or

0 has no effect. A 1 is always read back for this bit.

 

 

 

 

The complement of the value programmed into these three bits reflects

D5-D3

Interrupter IRQ Line

the selected IRQ line used by the module. A value of 0112 would select

IRQ4, a value of 0002 would select IRQ7, and a value of 1112 would

 

 

 

 

disconnect the IRQ lines.

D2-D0

Handler IRQ Line

The module has no interrupt handler capability; therefore writing to

these bits has no effect. A 1112 is always read back for these bits.

 

 

Note that all bits in this register are set to 1 upon receipt of a hard or soft reset.

 

 

Subclass Register (0x1E) — Read Only

 

D15

VXIbus Extended

Always reads as 1.

 

Device

 

 

 

 

D14-D0

Extended Memory

Always reads as 7FFD16

 

Device

 

 

 

 

 

 

NVM Access Resister (0x20) — Read Only

 

D15-D1

Unused

 

All Bits are always 1.

 

D0

 

 

Reads back the serial data stream from the selected SMIP II board.

 

 

 

Note that only one SMIP II board may be read back at a time.

 

 

 

 

 

 

 

NVM Access Resister (0x20) — Write Only

 

D15-D2

Unused

 

Data written to these bits have no effect.

 

D1

 

 

Serial clock for the switch module; should be a logic 1 when not used.

 

D0

 

 

Serial data input for the switch module; must be a logic 1 when not

 

 

 

used.

 

 

 

 

Board X, Y Used Address Register (0x22, 0x24, 0x26) — Read and Write

D15-D8

 

Sets the actual number of words of address space used by the relays on

 

board's X.

 

 

D7-D0

 

Sets the actual number of words of address space used by the relays on

 

board's Y.

 

 

SM7100 Programming

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents SM7100 VXI Technology, Inc Table of Contents Limitation of Warranty WarrantyCertification Restricted Rights LegendEMC C L a R a T I O N O F C O N F O R M I T YTerms and Symbols General Safety InstructionsAvoid Electric Shock Support Resources Programming OverviewVswr SM7100 SpecificationsSMA Setting the Chassis Backplane Jumpers Calculating System Power and Cooling RequirementsIntroduction MSB LSB Setting the Logical AddressSelecting the Extended Memory Space VXI Technology, Inc SM7100 Preparation for Use Front Panel Connection SM7000 Switch ConfigurationGND EXTReturn GND SM7100 Module Configuration SM7100 Matrix Schematic Offset Hex VXI Technology, Inc SM7100 Module Configuration Addressing Register AccessOffset Write Function Smip II Register MAP A16Logical Address Register 0x00 Write Only ID Register 0x00 Read OnlyDevice Type Register 0x02 Read Only Status Register 0x04 Read OnlyReserved Register 0x0A Read Only Offset Register 0x06 Read and WriteReserved Register 0x0C Read Only Version Number Register 0x0E Read OnlyNVM Access Resister 0x20 Write Only NVM Access Resister 0x20 Read OnlyInterrupt Control Register 0x1C Read and Write Subclass Register 0x1E Read OnlyTrace RAM Start Low Register 0x2A Read and Write Trace RAM Start High Register 0x28 Read and WriteTrace RAM End High Register 0x2C Read and Write Trace RAM End Low Register 0x2E Read and WriteTrace Enable Loop EnableOpen Trigger Select Register 0x36 -Write Only TTL Trigger Polarity Register 0x38 -Write OnlyTrigger Advance Register 0x3E Write Only Busy Trigger Control Register 0x3C Read and WriteBoard Busy Register 0x3E Read Only Reserved Registers Read and WriteAcfailn AddrBBM/MBB Control Register Read and Write Delay Register Read and Write Writing to the Relays Relay Register OffsetVIA16SPACE Index SM7100
Top Page Image Contents