Setting Surface Controls
•Operating the Bridge Radiant Surface Element Control
Operating the Bridge Surface Element
The cooktop is equipped with a "BRIDGE" surface element located at the left cooktop position (See Fig. 1). indicator lights on the control panel are used to indicate what portions of the Bridge element will heat. The Bridge element begins with the left FRONT position only (Fig. 2) and when selected with the +BRIDGE element (Fig. 3) it will provide a combination of 2 heating surfaces. When set for ALL 3 element positions the left rear element is added for a total combination of 3 even heating surfaces (See Fig. 4).
The Bridge element is designed for rectangular or oval shaped cookware. The griddle that is supplied with this appliance should be used with the Bridge element ONLY. For round shaped cookware, the left front element may be used as a single element.
| AIo | I |
| Ftotfl: | W |
Fig. 1 | Fig. B |
/\ o | i |
JR} Pt | qlP |
Fig. 3 | Fig. 4 |
To Operate the Bridge Surface Element:
1. | Place correctly sized | cookware on the radiant | surface | element. | m | ||
2. | Touch and hold the O | pad for the Bridge | element | position until a beep | |||
| is heard. The display will show" - - ". NOTE: Each time a pad is touched a |
| |||||
| beep will sound. If no further pads are touched within 10 seconds the |
| |||||
| request to power the element ON will clear. |
|
|
|
| ||
3. | Select the FRONT (See Fig. 2), +BRIDGE | (See Fig. 3) or ALL 3 elements | |||||
|
|
| Element |
| ,4 |
| |
| (See |
|
| twice or three times |
| ||
| Fig. 4) to heat by pressing the k_ | pau once, | ii!Viiill L,o | ||||
| (Figs. | 4 & 5 shows indicator lights with ALL | 3 elements selected). |
4.Touch the Bridge element (/X_'_ pad once to turn ON the power level Hi or
|
|
|
|
|
|
|
|
| ¸¸.¸.¸:¸¸¸¸¸¸.¸¸¸.¸¸¸¸¸¸..¸%¸¸ |
|
| (_pad | once for Lo (See Fig. 4). The Hot Surface | indicator light will |
|
| |||||
| turn ON when the element becomes hot. |
|
|
|
|
| ||||
5. | Each touch of the (_ | or _ | pad will decrease | or increase the power | Left | |||||
|
|
| v | v |
|
|
|
|
|
|
| level by 1/2 from 9.0 through 3.0. Simmer power levels | between 3.0 and 1.0 | Side | |||||||
| will decrease | or increase by .2 increments. | Lo is the lowest power level | Hot | Surface | |||||
| available. Note: The power level may be adjusted at any time while the | |||||||||
|
|
| ||||||||
| element | is ON. |
|
|
|
|
|
|
| |
6. | When cooking | has been completed | touch the O | pad once to turn the | Fig. 5 |
| ||||
|
|
|
|
|
| v |
|
|
|
|
| element | OFF. |
|
|
|
|
|
| NOTE: If all 3 Bridge elements are | |
|
|
|
|
|
|
|
|
| ||
| Each surface | element | provides a constant | amount of heat at each setting. A | selected, any previous power level | |||||
| setting for the LEFT REAR | element | ||||||||
| glowing | red surface heating area extending | beyond the bottom | edge of the | will be changed to the power level | |||||
| cookware indicates the cookware is too small for the surface | heating area. | setting for the Bridge. |
| ||||||
| Note: The Hot Surface indicator light will remain ON if the cooktop is still hot and will remain ON until the heating | |||||||||
| surface | area has cooled sufficiently. | If no element size is chosen when the Bridge | element is turned ON, the control will | ||||||
| default to the left front element only. See page 11, Fig. 1 for recommended surface cooking settings. |
| ||||||||
|
| Radiant surface elements may appear to have cooled after they have been turned off. The glass surface | ||||||||
may | still be hot and burns may occur | if the glass surface | is touched before it has cooled sufficiently. |
| ||||||
|
| Do not place aluminum foil or plastic items such as salt and pepper shakers, spoon holders or |
plastic wrappings on top of the range when it is in use. These items could melt or ignite. Potholders, towels or wooden spoons could catch fire if placed too close to the surface elements.
13