Kenmore 790.367 manual Setting Surface Controls contd, Setting the Bridge Burner some models, Off

Page 12

Setting Surface Controls (cont'd)

Setting the Bridge Burner (some models)

The Bridge Burner should be used with rectangular shaped cookware. Cookware like the cast-iron Griddle that is supplied with your range is designed specifically for best results with the Bridge Burner.

The Bridge Burner feature may be used to combine the cooking power of 2 or if needed 3 gas surface Burners located along the left-hand side of the glass cooktop. The left rear and left center Burners are controlled by the left rear surface Control Knob. In addition the left front Burner may be added to the Bridge Burner with the left front gas Control Knob (See Figure 1).

Operating the Bridge Burner (some models)

1.Push the left rear surface control knob in and turn counterclockwise out of the OFF position (See Figure 2).

2.Release the knob and rotate to the LITE position (See Figures 2 & 3). Note: All electronic surface ignitors will spark at the same time. However, only the selected surface Burner will lite.

3.Visually check that the left rear Burner has lit.

4.Continue to rotate the gas control knob clockwise past the first LO setting to the arrow marked BRIDGE.

5.Visually check that both the left rear and left center Burners are lit.

6.When both burners are lit, continue to turn the control knob

counterclockwise to adjust to the desired flame size for both burners together. Note: The markings between the 2nd HI and LO settings on the left rear control knob adjust the flame size for both burners. Use the guide marks between the 2nd HI and LO settings and adjust the flame size as needed (Refer to Figure 3).

7.Add the left front Burner if needed. Once lit, visually adjust the flame size of the left front Burner to match the flame size of the Bridge Burner.

8.Place cooking utensil centered over the left-hand cooktop surface Burner Grate. DO NOT cook with any of the surface control knobs in the LITE position (The electronic ignitor will continue to spark if the knob is left in the LITE position).

Note: If only the left rear surface Burner is needed, follow the instructions provided below.

Operating only the Left rear Gas Surface Burner (some models)

1.Place cooking utensil centered over the left-rear surface Burner Grate.

2.Push the left rear surface control knob in and turn counterclockwise out of the OFF position (See Figure 2).

3.Release the knob and rotate to the LITE position. Note: All electronic surface ignitors will spark at the same time. However, only the left rear Burner will ignite.

4.Visually check that the left-rear burner has lit. Adjust the flame size by turning the control knob between the first HI and LO settings (See Figure 3). DO NOT cook with the surface control knob in the LITE position (The electronic ignitor will continue to spark if the knob is left in the LITE

position).

Left Rear Burner

 

 

flame adjustment

 

area

-- b

Figure 1

Figure 2

OFF

iiiiiiiiiiiiiiiii;¸ \

iiiiiiiiiiiiiiiiii\_i iiiiiiiiiiiiiiiii.... \

Lo

Bridge Burner--

_E

LITE position

H I

Bridge Burner

flame adjustment

Figure 3 area

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A 318203857 Rev. BTable of Contents Installation and service InstallerProper Installation-Be sure your appliance is properly Removing leveling legs, panels, wire covers, anti-tipImportant Instructions for Using For Glass Cooktops onlyImportant Instructions for Cleaning Your Range Self Cleaning OvensProduct Record Serial Plate LocationU.S.A Master Protection AgreementsFor prices and additional information call Grounding instructions Range Features At a Glance Your Slide=InOoobtu Before Setting Surface Controls BurnerBefore Setting Surface Controls Setting Surface Controls Setting Proper Surface Burner Flame SizeOperating the Gas Surface Controls Type of CookingSetting Surface Controls contd Setting the Bridge Burner some modelsOperating the Bridge Burner some models Operating only the Left rear Gas Surface Burner some modelsSurface Cooking CorrectINCORRECT Before Setting Oven Controls Using the GriddleSurface Cooking contd Care & Seasoning of the GriddleBefore Setting Oven Controls contd ForControl Pad Features Control Pad SettingsMaximum Setting Oven Controls InstructionspressTo Set Add 1 Minute Feature PressDisplay InstructionsSetting Oven Controls INSTRUCTiONSPress DisplaySetting Temperature Display -- Fahrenheit or Celsius InstructionsPressdisplay Setting Preheat To set the Preheat temperature example 350FSetting Setting BakeTo set the Bake Temperature example 350F ContSetting Oven Controls contd Baking ProblemsProblems Oven Baking informationSetting Convection Bake QQdbSetting Convection Convert Feature InstructionspressSetting the Slow Cook Feature Instructions Press DisplaySetting OvenControls Contd CookTimeSetting Delayed Start Bake or Convection Bake DelayWE,COOK Timed BakeSetting Oven Controls contd Setting the Food Categories Feature Meats M-ACAKESS BreadsRoasting instructions for Meats Pad CategorySetting the Warm & Hold TM Feature To set Warm & HoldTo set Warm & Hold to turn on automatically Setting Broil To set the oven to broil at the default setting 550FPress Display Broiling Times and Searing GrillSetting Oven ContdRecipe example recording Bake at 350F for 30 minutes To Begin Baking with the Stored RecipeSetting Warmer Drawer Controls Warmer Drawer Food Temperature SettingsArranging Warmer Warm & Ready TM Drawer Rack Positions MEDSetting Warmer Drawer Controls contd To Set the Warmer Drawer & Bread Proof ControlsPreparing Bread Dough for the Warmer Drawer Self-Cleaning What to Expect during CleaningAdhere to the following cleaning precautions Self=Cleaning Contd Self-Clean Cycle Time LengthWhen the Self-Clean Cycle is Completed Self=Cleaning contd Adjusting Oven TemperatureInstructions Press General Care & Cleaning Cleaning Various Parts of Your RangeAluminum & Vinyl Control Panel and Trim Pieces Glass, Painted and PlasticGeneral Care & Cleaning contd Cleaning the Cooktop, Burner Heads, Caps & GratesCeramic Glass Cooktop Cleaning and Maintenance Cleaning Recommendations for the Ceramic Glass CooktopRemoving and Replacing the Oven Door Removing and Replacing Warmer Warm & Ready TM Drawer Changing the Oven LightPossible CAUSE/SOLUTION OccurrenceFlames inside oven or Smoking from ventMY-H 0 M E 14oo-469-4663 CanadaCall anytime, day or night U.S.A. only

790.3671, 790.367 specifications

The Kenmore 790.367 and 790.3671 models represent a versatile line of gas ranges engineered for both amateur cooks and culinary enthusiasts. With their combination of sleek design and advanced features, these appliances stand out in any kitchen setting.

One of the hallmark characteristics of the Kenmore 790.367 series is its robust construction. The stainless steel finish not only enhances the visual appeal of the range but also ensures durability and ease of cleaning. This model incorporates a spacious oven capacity, allowing users to prepare large meals or multiple dishes at once, a desirable trait for family gatherings or dinner parties.

The cooking surface of the Kenmore 790.367 features sealed burners that provide even heat distribution, reducing the risk of hot spots and ensuring more consistent cooking results. With various burner sizes, including a powerful high-heat burner ideal for boiling water quickly, home chefs have the flexibility to choose the right burner for their culinary needs.

In addition to its physical features, the Kenmore 790.367 series is equipped with advanced cooking technologies. One notable feature is the Smart Oven technology, which includes an electronic control panel that simplifies temperature adjustments and cooking time settings. The oven also features multiple cooking modes, including bake, broil, and convection, allowing users to achieve their preferred cooking style effortlessly.

Safety is a priority in the design of these ranges as well. The Kenmore 790.367 series includes a built-in oven light that illuminates the cooking chamber, so users can keep an eye on their dishes without opening the oven door. Additionally, the range comes with an automatic shut-off feature, providing peace of mind for those who may forget to turn off the stove after cooking.

Furthermore, the self-cleaning option allows for hassle-free maintenance, making it easier for users to keep their range looking as good as new with minimal effort. Overall, the Kenmore 790.367 and 790.3671 are designed to combine convenience, safety, and performance, making them an excellent choice for modern kitchens. With their impressive features and user-friendly technologies, these ranges are sure to meet the demands of today's home cooks, offering both functionality and style.
Top Page Image Contents