Kenmore 630.13952 For access to heaters & NTC’s, To remove heater, NTC & flow switch, Repair

Page 34

Repair

2.Push latch on back of control toward rear of dishwasher, then slide control from base.

mCAUTION – 75% of all controls returned for analysis check out OK. Most control issues are due to loose connections.

VE. Heaters

The heater, NTC and flow switch can be accessed or measured from the right side of the dishwasher, but the heater and NTC can only be removed by removing the base (by flipping the dishwasher upside-down) since the heater fits tightly underneath the tank.

For access to heaters & NTC’s

Tools needed: Phillips and T-20 Torx screwdriver, pliers.

1.Remove toe kick – see section VA.

2.Flip dishwasher upside-down & remove base – see section VA.

To remove heater, NTC & flow switch

1.Loosen pump - heater hose clamp and remove two T-20 Torx screws holding heater assembly to sump.

2.Carefully pull heater from sump & pump. The heater comes as an assembly with housing & gasket.

702_58300000149896_ara_en_b

Image 34

Contents Hoffman Estates, IL 60179 U.S.A KENMORE ELITE DISHWASHERSSears Brands Management Corporation Toronto, Ontario, Canada M5B 2C3WIRING DIAGRAMS FAULT DIAGNOSTICSTECHNICAL SPECIFICATIONS COMPONENTSIA. General hazards m I. SAFETYSAFETY IB. Electrical shock / fire hazards c hIIA. Pre-Installchecklist II. INSTALLATIONINSTALLATION IIB. AlignmentIIC. Electrical connection INSTALLATION IID. Water connection IIE. Drain and condensation hose connectionsSanitized and Refill Rinse Agent lights Reset “Cancel – Reset”III. OPERATION Dry AssistEnd of cycle tone Changing basic featuresThe End of cycle tone volume can be changed IIIC. Entering special programs and codingP4 = Control coding see CX control codes EX Error codesPX Program codes CX Control codesPreparing a showroom dishwasher for resale Preparing a dishwasher for showroom useWARNING: Danger of electrical shock Dispenser Adjusting rinse-aiddosageClosing dispenser doors Heater Operation IV.COMPONENTSTank Heater ratingsMicroswitch Cam Water switchLeveling feet front and rear DiskBLDC Circulation pumpsFloat Drain pump Pump specificationsSolving installation issues CavitatingWater fill assembly Terminal connections Rast 5 connectorsJohnson Tee installations Washington State SiphoningFlowmeter Condensation tube Using hinge slider sliding pulleyDoor spring Hinge bushing Water inlet valveTerminal block On/off switchDoor latch Terminal boxDrain hose Optical rinse-aidsensors Power module Display and power modulesAqua sensor Control moduleSump Sump partsBackflow check valve Spray arm feed tube Info lightsOperation Water circulationSerial label warranty information Understanding the 17-digitserial #Tools needed: T20 Torx screwdriver V. RepairTo remove outer door To remove toe kickTo flip dishwasher upside-down To raise block up right side of tank Tools needed: T20 Torx screwdriver and pliersTools needed: T20 Torx screwdriver & pliers For access to circulation pumpTo remove water valve Connection hintsFascia panel mounted controls To remove complete pumpTools needed: flat blade screwdriver Tools needed: T-20Torx & flat blade screwdriversTools needed: T-20Torx screwdriver & pliers To access base-mountedcontrolsBase mounted controls 1.Remove outer door – see section VATo remove heater, NTC & flow switch For access to heaters & NTC’sVE. Heaters Softer bearing heaters 4.Push NTC latches and lift NTC from heaterRepair VF. 2-piecedrain hose connection To remove dispensers1.Remove outer door --section VA VG. Drain pumps1.Remove fascia panel --section VD To remove door latchesVI. Door latches Misaligned door latches Fault Diagnostics VI.Fault DiagnosticsEntering customer service test program VIA. Customer service test programError code displays Clearing error codesViewing customer service program SymbolFailure Resolution Dishwasher troubleshootingFault Steps to determine failureDispenser or does not Heater diagnosingWill not fill fill withHeating system checklist if controls time out Controls timing out and showing “1”NTC resistance chart Where to measure NTC resistancesWater Leaking Past Doors Checklist if water leaks past doorsCosmetic / Customer Use / Installation Issues Not cleaning or locking sump filtersCustomer self-helpdiagnosing Technical Specifications VII. Technical SpecificationsUnsatisfactory washing results VIII. Wiring Diagrams Wiring DiagramsWiring Diagrams 702_58300000149896_ara_en_b