Kenmore 630.13953, 630.13959, 630.13952 manual To flip dishwasher upside-down

Page 29

Repair

To flip dishwasher upside-down

Tools needed: T20 Torx screwdriver, Phillips screwdriver and pliers.

1.Turn off water and electricity. Disconnect dishwasher mounting brackets (1).

2.Remove toe kick by removing two Phillips screws and tilting toe kick out from dishwasher (2).

3.Disconnect water line and electric supply (3).

4.Pull dishwasher out, place a pad or cardboard on the floor and carefully flip the dishwasher upside-down (4).

5.Remove four base screws from front of dishwasher (5).

6.Remove two screws securing water valve to base. There’s no need to disconnect valve wire harness or inlet hoses (6).

7.Pull wire harness connector from rear of terminal box (7).

8.Push latch on base-mounted control to disconnect it from base (8).

9.Remove both door springs from base (9).

10.Remove two tank screws from rear of dishwasher (10), disconnect both rubber circulation pump supports (11) and carefully lift up base from dishwasher (12).

702_58300000149896_ara_en_b

Image 29

Contents Sears Brands Management Corporation KENMORE ELITE DISHWASHERSHoffman Estates, IL 60179 U.S.A Toronto, Ontario, Canada M5B 2C3TECHNICAL SPECIFICATIONS FAULT DIAGNOSTICSWIRING DIAGRAMS COMPONENTSSAFETY I. SAFETYIA. General hazards m IB. Electrical shock / fire hazards c hINSTALLATION II. INSTALLATIONIIA. Pre-Installchecklist IIB. AlignmentIIC. Electrical connection IIE. Drain and condensation hose connections INSTALLATION IID. Water connectionIII. OPERATION Reset “Cancel – Reset”Sanitized and Refill Rinse Agent lights Dry AssistThe End of cycle tone volume can be changed Changing basic featuresEnd of cycle tone IIIC. Entering special programs and codingPX Program codes EX Error codesP4 = Control coding see CX control codes CX Control codesWARNING: Danger of electrical shock Preparing a dishwasher for showroom usePreparing a showroom dishwasher for resale Closing dispenser doors Adjusting rinse-aiddosageDispenser Tank IV.COMPONENTSHeater Operation Heater ratingsLeveling feet front and rear Water switchMicroswitch Cam DiskFloat Circulation pumpsBLDC Solving installation issues Pump specificationsDrain pump CavitatingJohnson Tee installations Washington State Terminal connections Rast 5 connectorsWater fill assembly SiphoningFlowmeter Door spring Using hinge slider sliding pulleyCondensation tube Water inlet valve Hinge bushingDoor latch On/off switchTerminal block Terminal boxDrain hose Optical rinse-aidsensors Aqua sensor Display and power modulesPower module Control moduleBackflow check valve Sump partsSump Info lights Spray arm feed tubeWater circulation OperationUnderstanding the 17-digitserial # Serial label warranty informationTo remove outer door V. RepairTools needed: T20 Torx screwdriver To remove toe kickTo flip dishwasher upside-down Tools needed: T20 Torx screwdriver and pliers To raise block up right side of tankTo remove water valve For access to circulation pumpTools needed: T20 Torx screwdriver & pliers Connection hintsTools needed: flat blade screwdriver To remove complete pumpFascia panel mounted controls Tools needed: T-20Torx & flat blade screwdriversBase mounted controls To access base-mountedcontrolsTools needed: T-20Torx screwdriver & pliers 1.Remove outer door – see section VAVE. Heaters For access to heaters & NTC’sTo remove heater, NTC & flow switch 4.Push NTC latches and lift NTC from heater Softer bearing heaters1.Remove outer door --section VA To remove dispensersRepair VF. 2-piecedrain hose connection VG. Drain pumpsVI. Door latches To remove door latches1.Remove fascia panel --section VD Misaligned door latches Entering customer service test program VI.Fault DiagnosticsFault Diagnostics VIA. Customer service test programClearing error codes Error code displaysSymbol Viewing customer service programFault Dishwasher troubleshootingFailure Resolution Steps to determine failureDispenser Will not fill Heater diagnosingor does not fill withControls timing out and showing “1” Heating system checklist if controls time outWhere to measure NTC resistances NTC resistance chartCosmetic / Customer Use / Installation Issues Checklist if water leaks past doorsWater Leaking Past Doors Not cleaning or locking sump filtersCustomer self-helpdiagnosing Unsatisfactory washing results VII. Technical SpecificationsTechnical Specifications Wiring Diagrams VIII. Wiring Diagrams702_58300000149896_ara_en_b Wiring Diagrams