Kenmore 630.13959, 630.13952 manual VI.Fault Diagnostics, Entering customer service test program

Page 39

Fault Diagnostics

Fault Diagnostics

VI.Fault Diagnostics

VIA. Customer service test program

Entering customer service test program

Controls contain codes for factory tests, customer service test program, dishwasher configuration and error codes. Consult test programs and error codes for your dishwasher before using the codes from this manual.

1.Open the door.

2.While pushing (and holding) any two wash cycle buttons, turn the dishwasher on with the on/off switch. While the buttons are held, the model coding will show (e.g. “C2”, “C5”, etc.). After releasing the buttons, LED “B” will be lit, LED “C” will flash and “P0” will display, confirming you’re in the special programs menu.

3.To select the test program, push button “B” repeatedly until “P1” is displayed or until LED “C” is lit.

4.Push button “C” to start the program -- LED “C” will blink. Close the door after pushing button “C”). The steps will show on the digital display (e.g.- "S:01") -- push button “B” to skip a step.

Stored error codes will show on the digital display and LED’s (see Error code displays on the next page).

The test program can only be stopped / reset by pushing the on/off button – it can’t be done by turning off the power.

702_58300000149896_ara_en_b

Image 39

Contents Toronto, Ontario, Canada M5B 2C3 KENMORE ELITE DISHWASHERSSears Brands Management Corporation Hoffman Estates, IL 60179 U.S.ACOMPONENTS FAULT DIAGNOSTICSTECHNICAL SPECIFICATIONS WIRING DIAGRAMSIB. Electrical shock / fire hazards c h I. SAFETYSAFETY IA. General hazards mIIB. Alignment II. INSTALLATIONINSTALLATION IIA. Pre-InstallchecklistIIC. Electrical connection IIE. Drain and condensation hose connections INSTALLATION IID. Water connectionDry Assist Reset “Cancel – Reset”III. OPERATION Sanitized and Refill Rinse Agent lightsIIIC. Entering special programs and coding Changing basic featuresThe End of cycle tone volume can be changed End of cycle toneCX Control codes EX Error codesPX Program codes P4 = Control coding see CX control codesPreparing a dishwasher for showroom use Preparing a showroom dishwasher for resaleWARNING: Danger of electrical shock Adjusting rinse-aiddosage DispenserClosing dispenser doors Heater ratings IV.COMPONENTSTank Heater OperationDisk Water switchLeveling feet front and rear Microswitch CamCirculation pumps BLDCFloat Cavitating Pump specificationsSolving installation issues Drain pumpSiphoning Terminal connections Rast 5 connectorsJohnson Tee installations Washington State Water fill assemblyFlowmeter Using hinge slider sliding pulley Condensation tubeDoor spring Water inlet valve Hinge bushingTerminal box On/off switchDoor latch Terminal blockDrain hose Optical rinse-aidsensors Control module Display and power modulesAqua sensor Power moduleSump parts SumpBackflow check valve Info lights Spray arm feed tubeWater circulation OperationUnderstanding the 17-digitserial # Serial label warranty informationTo remove toe kick V. RepairTo remove outer door Tools needed: T20 Torx screwdriverTo flip dishwasher upside-down Tools needed: T20 Torx screwdriver and pliers To raise block up right side of tankConnection hints For access to circulation pumpTo remove water valve Tools needed: T20 Torx screwdriver & pliersTools needed: T-20Torx & flat blade screwdrivers To remove complete pumpTools needed: flat blade screwdriver Fascia panel mounted controls1.Remove outer door – see section VA To access base-mountedcontrolsBase mounted controls Tools needed: T-20Torx screwdriver & pliersFor access to heaters & NTC’s To remove heater, NTC & flow switchVE. Heaters 4.Push NTC latches and lift NTC from heater Softer bearing heatersVG. Drain pumps To remove dispensers1.Remove outer door --section VA Repair VF. 2-piecedrain hose connectionTo remove door latches 1.Remove fascia panel --section VDVI. Door latches Misaligned door latches VIA. Customer service test program VI.Fault DiagnosticsEntering customer service test program Fault DiagnosticsClearing error codes Error code displaysSymbol Viewing customer service programSteps to determine failure Dishwasher troubleshootingFault Failure ResolutionDispenser fill with Heater diagnosingWill not fill or does notControls timing out and showing “1” Heating system checklist if controls time outWhere to measure NTC resistances NTC resistance chartNot cleaning or locking sump filters Checklist if water leaks past doorsCosmetic / Customer Use / Installation Issues Water Leaking Past DoorsCustomer self-helpdiagnosing VII. Technical Specifications Technical SpecificationsUnsatisfactory washing results Wiring Diagrams VIII. Wiring Diagrams702_58300000149896_ara_en_b Wiring Diagrams