Kenmore 630.13959 manual To remove dispensers, Remove outer door --section VA, VG. Drain pumps

Page 36

Repair

Repair

VF. 2-piece drain hose connection

Drain hoses come in two pieces, an external (customer) drain hose and an internal drain hose. The 90º elbow of the external hose is connected to the outlet of the internal hose (pointing toward the drain) and is held in place by a hose clamp.

To remove the internal drain hose, remove a white plastic hose lock and pull the hose from the water level control.

VG. Drain pumps

To access pump, disconnect inlet hose and pump harness. To remove pump,

(1)pull latch (on circular collar), (2) rotate pump clockwise (cw) ~ 1/8 turn and

(3)pull out pump. To install new pump, insert @ 2:00 position & rotate counterclockwise (ccw).

VH. Dispensers

Dispensers can be accessed from the front by removing the outer door.

Tools needed: Small flat blade and T-20 Torx screwdrivers.

To remove dispensers

1.Remove outer door -- section VA.

2.Disconnect wire harnesses from dispenser. Don’t remove the cable tie keeping the harness away from the dispenser. It must be replaced if it’s removed.

3.Using a small flat blade screwdriver, push the six inner door tabs holding the dispenser.

4.Carefully push the dispenser in toward the inside of the inner door.

702_58300000149896_ara_en_b

Image 36

Contents KENMORE ELITE DISHWASHERS Sears Brands Management CorporationHoffman Estates, IL 60179 U.S.A Toronto, Ontario, Canada M5B 2C3FAULT DIAGNOSTICS TECHNICAL SPECIFICATIONSWIRING DIAGRAMS COMPONENTSI. SAFETY SAFETYIA. General hazards m IB. Electrical shock / fire hazards c hII. INSTALLATION INSTALLATIONIIA. Pre-Installchecklist IIB. AlignmentIIC. Electrical connection INSTALLATION IID. Water connection IIE. Drain and condensation hose connectionsReset “Cancel – Reset” III. OPERATIONSanitized and Refill Rinse Agent lights Dry AssistChanging basic features The End of cycle tone volume can be changedEnd of cycle tone IIIC. Entering special programs and codingEX Error codes PX Program codesP4 = Control coding see CX control codes CX Control codesPreparing a dishwasher for showroom use Preparing a showroom dishwasher for resaleWARNING: Danger of electrical shock Adjusting rinse-aiddosage DispenserClosing dispenser doors IV.COMPONENTS TankHeater Operation Heater ratingsWater switch Leveling feet front and rearMicroswitch Cam DiskCirculation pumps BLDCFloat Pump specifications Solving installation issuesDrain pump CavitatingTerminal connections Rast 5 connectors Johnson Tee installations Washington StateWater fill assembly SiphoningFlowmeter Using hinge slider sliding pulley Condensation tubeDoor spring Hinge bushing Water inlet valveOn/off switch Door latchTerminal block Terminal boxDrain hose Optical rinse-aidsensors Display and power modules Aqua sensorPower module Control moduleSump parts SumpBackflow check valve Spray arm feed tube Info lightsOperation Water circulationSerial label warranty information Understanding the 17-digitserial #V. Repair To remove outer doorTools needed: T20 Torx screwdriver To remove toe kickTo flip dishwasher upside-down To raise block up right side of tank Tools needed: T20 Torx screwdriver and pliersFor access to circulation pump To remove water valveTools needed: T20 Torx screwdriver & pliers Connection hintsTo remove complete pump Tools needed: flat blade screwdriverFascia panel mounted controls Tools needed: T-20Torx & flat blade screwdriversTo access base-mountedcontrols Base mounted controlsTools needed: T-20Torx screwdriver & pliers 1.Remove outer door – see section VAFor access to heaters & NTC’s To remove heater, NTC & flow switchVE. Heaters Softer bearing heaters 4.Push NTC latches and lift NTC from heaterTo remove dispensers 1.Remove outer door --section VARepair VF. 2-piecedrain hose connection VG. Drain pumpsTo remove door latches 1.Remove fascia panel --section VDVI. Door latches Misaligned door latches VI.Fault Diagnostics Entering customer service test programFault Diagnostics VIA. Customer service test programError code displays Clearing error codesViewing customer service program SymbolDishwasher troubleshooting FaultFailure Resolution Steps to determine failureDispenser Heater diagnosing Will not fillor does not fill withHeating system checklist if controls time out Controls timing out and showing “1”NTC resistance chart Where to measure NTC resistancesChecklist if water leaks past doors Cosmetic / Customer Use / Installation IssuesWater Leaking Past Doors Not cleaning or locking sump filtersCustomer self-helpdiagnosing VII. Technical Specifications Technical SpecificationsUnsatisfactory washing results VIII. Wiring Diagrams Wiring DiagramsWiring Diagrams 702_58300000149896_ara_en_b