Kenmore 630.13959, 630.13952, 630.13953 manual Customer self-helpdiagnosing, Fault Diagnostics

Page 48
Customer self-help diagnosing

Fault Diagnostics

Dispensers -- Customers using too much detergent, not using rinse-aid & not knowing how to close the door.

Drain hoses not installed properly --Often no air gap or high loop + pinched hoses -- causes poor draining & smelly dishwashers. Most drain pumps are mistakenly replaced for drain hose installation issues.

Outer doors -- Most are dinged during shipment.

Damaged water valves -- Primarily from fittings being overtightened. A damaged valve can allow some water onto kitchen floors.

Customer self-help diagnosing

Dishwashers may occasionally exhibit problems unrelated to a dishwasher failure. The following fixes can be made by customers without calling for repair.

Dishes do not dry -- The rinse agent dispenser may be empty. Check the rinse-aid dispenser and refill it if necessary. Dishware drying can be accelerated and enhanced by opening the dishwasher door slightly and propping it open with the top rack.

Indicator light(s) do not come on -- A fuse may have blown or a circuit breaker tripped. Check the fuse or circuit breaker at your fuse box/breaker box and replace the fuse or reset the breaker if necessary.

Dishwasher does not start -- The dishwasher door may not be properly shut. Make certain the dishwasher door is shut and latched.

Dishwasher runs a long time -- If the dishwasher completes the cycle, but the run time seems exceptionally long, it may be due to cold incoming water. Before starting the dishwasher, open the hot water faucet at the sink nearest the dishwasher. Run the water until it runs hot, then turn off the water and start the dishwasher.

Machine cycle does not advance to rinse -- The water supply line may be shut off. Check the water supply valve and open it if it’s shut.

White spots left on dishes -- More rinse agent is needed.

Water not pumped from dishwasher

oMake certain the drain hose isn’t kinked, clogged, or improperly installed. Make sure the drain hose is at least 20 inches above the floor.

oMake certain the dishwasher filter system and kitchen sink drain aren’t clogged. You may need a plumber rather than a serviceman for the dishwasher. If an air gap is installed at sink, it may be clogged.

Detergent dispenser cover will not shut – The cover may not have been shut correctly or a cycle was not finished and should’ve been cancelled.

Streaks on glassware -- Too much rinse agent is being dispensed.

Rattling noises -- Utensils may not be properly arranged.

Suds in dishwasher – The customer may have used the wrong type of dishwashing detergent. Use only automatic dishwasher detergents.

702_58300000149896_ara_en_b

Image 48
Contents KENMORE ELITE DISHWASHERS Sears Brands Management CorporationHoffman Estates, IL 60179 U.S.A Toronto, Ontario, Canada M5B 2C3FAULT DIAGNOSTICS TECHNICAL SPECIFICATIONSWIRING DIAGRAMS COMPONENTSI. SAFETY SAFETYIA. General hazards m IB. Electrical shock / fire hazards c hII. INSTALLATION INSTALLATIONIIA. Pre-Installchecklist IIB. AlignmentIIC. Electrical connection INSTALLATION IID. Water connection IIE. Drain and condensation hose connectionsReset “Cancel – Reset” III. OPERATIONSanitized and Refill Rinse Agent lights Dry AssistChanging basic features The End of cycle tone volume can be changedEnd of cycle tone IIIC. Entering special programs and codingEX Error codes PX Program codesP4 = Control coding see CX control codes CX Control codesPreparing a dishwasher for showroom use Preparing a showroom dishwasher for resaleWARNING: Danger of electrical shock Adjusting rinse-aiddosage DispenserClosing dispenser doors IV.COMPONENTS TankHeater Operation Heater ratingsWater switch Leveling feet front and rearMicroswitch Cam DiskCirculation pumps BLDCFloat Pump specifications Solving installation issuesDrain pump CavitatingTerminal connections Rast 5 connectors Johnson Tee installations Washington StateWater fill assembly SiphoningFlowmeter Using hinge slider sliding pulley Condensation tubeDoor spring Hinge bushing Water inlet valveOn/off switch Door latchTerminal block Terminal boxDrain hose Optical rinse-aidsensors Display and power modules Aqua sensorPower module Control moduleSump parts SumpBackflow check valve Spray arm feed tube Info lightsOperation Water circulationSerial label warranty information Understanding the 17-digitserial #V. Repair To remove outer doorTools needed: T20 Torx screwdriver To remove toe kickTo flip dishwasher upside-down To raise block up right side of tank Tools needed: T20 Torx screwdriver and pliersFor access to circulation pump To remove water valveTools needed: T20 Torx screwdriver & pliers Connection hintsTo remove complete pump Tools needed: flat blade screwdriverFascia panel mounted controls Tools needed: T-20Torx & flat blade screwdriversTo access base-mountedcontrols Base mounted controlsTools needed: T-20Torx screwdriver & pliers 1.Remove outer door – see section VAFor access to heaters & NTC’s To remove heater, NTC & flow switchVE. Heaters Softer bearing heaters 4.Push NTC latches and lift NTC from heaterTo remove dispensers 1.Remove outer door --section VARepair VF. 2-piecedrain hose connection VG. Drain pumpsTo remove door latches 1.Remove fascia panel --section VDVI. Door latches Misaligned door latches VI.Fault Diagnostics Entering customer service test programFault Diagnostics VIA. Customer service test programError code displays Clearing error codesViewing customer service program SymbolDishwasher troubleshooting FaultFailure Resolution Steps to determine failureDispenser Heater diagnosing Will not fillor does not fill withHeating system checklist if controls time out Controls timing out and showing “1”NTC resistance chart Where to measure NTC resistancesChecklist if water leaks past doors Cosmetic / Customer Use / Installation IssuesWater Leaking Past Doors Not cleaning or locking sump filtersCustomer self-helpdiagnosing VII. Technical Specifications Technical SpecificationsUnsatisfactory washing results VIII. Wiring Diagrams Wiring DiagramsWiring Diagrams 702_58300000149896_ara_en_b