Craftsman 917.273062 owner manual Engine, Lubrication

Page 22

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to "leak" power.

1.Remove terminal guard.

2.Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.

3.Rinse the battery with plain water and dry.

4.Clean terminals and battery cable ends with wire brush until bright.

5.Coat terminals with grease or petro- leum jelly.

6.Reinstall battery (See "REPLACING BATTERY" in the SERVICE AND

ADJUSTMENTS section of this manual).

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable.

Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

The transmission fan and cooling fins should be kept clean to assure proper cooling.

Do not attempt to clean fan or transmis- sion while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high

pressure water or steam to clean transaxle.

•Inspect cooling fan to be sure fan blades are intact and clean.

•Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins.

TRANSAXLE PUMP FLUID

The transaxle was sealed at the factory

and fluid maintenance is not required for the life of the transaxle. Should the

transaxle ever leak or require servicing, contact your nearest authorized service center/department.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SF, SG, or SH. Select the oil's SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

Change the oil after every 50 hours of

operation or at least once a year if the tractor is not used for 50 hours in one

year.

Check the crankcase oil level before starting the engine and after each eight

(8)hours of operation. "Rghten oil fill cap/ dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range expected before oil change. All oil must meet API service classification SF, SG, or SH.

*Be sure tractor is on level surface.

o Oil will drain more freely when warm.

*Catch oil in a suitable container.

1.Remove oil fill cap/dipstick. Be careful

not to allow dirt to enter the engine when changing oil.

2.Remove drain plug.

3.After oil has drained completely, replace oil drain plug and tighten securely.

4.Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not

overfill. For approximate capacity see

"PRODUCT SPECIFICATIONS" section of this manual.

5.Use gauge on oil fill cap/dipstick for checking level. Insert dipstick into the tube and rest the oil fill cap on the tube. Do not thread the cap onto the

tube when taking reading. Keep oil at "FULL" line on dipstick. Tighten cap onto the tube securely when finished.

Air

Screen_

Oil Drain Plug

_FII Cap/

Dipstick

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Icraftsmani Limitedtwo Yearwarranty on Craftsman Riding Equipm ENT Parts Limited 90 DAY Warranty on BatteryI1.SLOPE Operation General OperationDo not Ill. Children Page Repair Agreement Product SpecificationsCustomer Responsibilities Seat To Remove Tractor from Tools Required for AssemblyUnpack Carton Install Seat HOW to SET UP Your TractorCheck Battery Before Removing Tractor from SkidPage Install Mower and Drive Belt Check Mower Levelness ChecklistChecktire Pressure Check for Proper Position ALL BeltsClutch Disengaged Know Your Tractor To SET Parking Brake HOW to USE Your TractorTo Move Forward Backward To Operate Mower To Adjust Gauge WheelsTo Operate on Hills Before Starting the Engine MentsAutomatic Transmission Warm UP To Start EnginePurge Transmission Mowing Tips General Recommendations Lubrication ChartBefore Each USE Operator Presence System BatteryBlade Removal Engine LubricationEngine OIL Filter Clean AIR ScreenCleaning MufflerSIDE-TO-SIDE Adjustment To Install MowerTo Level Mower Housing To Remove MowerTo Replace Mower Drive Belt Mower Drive Belt InstallationMower Drive Belt Removal To Replace Mower Blade Drive Belt To Adjust Attachment ClutchTo Replace Mower Drive Belt Belt Installation To Adjust BrakeBelt Removal Front Wheel TOE-INADJUSTMENT To Adjust Motion Control LeverTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACE- MentReplacing Battery To Start Engine with a Weak BatteryTo Remove Wheel for Repairs To Replace Headlight Bulb To Adjust Attachment Lift SpringTo Remove Hood and Grill AS Sembly Preliminary Setting To Adjust Choke ControlTo Adjust Carburetor Final SettingFuel System BatteryOther Engine OILProblem Cause CorrectionTroubleshooting Problem ChartFast Troubleshooting ChartCause Correction SlowPage Schematic Tractor Model Number 917,273062 ELECTa£CkuzcHTractor -- Model Number Electrical Tractor --MODEL Number Electrical KEY Part DescriptionTractor Model Number 917.273062 Chassis and Enclosures Tractor --MODEL Number Chassis and Enclosures DescriptionTractor Model Number Ground Drive Tractor --MODEL Number Ground Drive UNCTractor Model Number Steering Tractor -- Model Number SteeringTractor Model Number Engine Spark Arrester KITEngine KEY PartTractor --MODEL Number Seat Assembly KEY Part NO. NO. DescriptionWheels and Tires Tractor Model NumberDecals Tractor -- Model Number Lift Assembly KEY Part NO. NO,DESCRIPTION Tractor Model Number Mower Deck Tractor --MODEL Number Mower Deck KEY Part NO. NO.DESCRIPTION111 Tractor --MODEL Number TRANSAXLE--MODEL Number 222-3010L KEY Part Description144569 Shaft Pump 127148X Swashplate Ylinder HEAD, Valve and Breatherj IGNITION/ELECTRICALJ Blower Housing and Bafflesj Tractor =-MODEL Number Exhaustj HEAD/VALVE/BREATHER Crankcase KEY Part Tractor --MODEL NUM BER Kohler ENGINE-MODEL Number CV20S, Type NumberTRACTOR-- Model NUM BER KEY Part NO. NO.DESCRIPTIONKohler ENGINE-MODEL Number CV20S, Type Number Page Page Suggested Guide for Sighting Slopes for Safe Operation Get it fixed, at your home or ours

917.273062 specifications

The Craftsman 917.273062 is a high-performance riding lawn mower designed for residential and light commercial use, blending efficiency, power, and ease of operation. This robust machine is ideal for users seeking to maintain larger lawns or properties with varying terrains.

One of the standout features of the Craftsman 917.273062 is its powerful engine. Equipped with a 19.5 horsepower Briggs & Stratton engine, this mower delivers reliable performance, offering ample power to handle thick grass and uneven surfaces. The engine's design ensures smooth operation with reduced noise levels, making mowing more pleasant.

The mower features a 42-inch cutting deck, allowing it to cover vast areas in a single pass. This deck design incorporates a twin-blade system, which enhances cutting efficiency and provides a clean, even cut. The adjustable cutting heights, ranging from 1.5 inches to 4 inches, allow users to customize their mowing experience based on their lawn's specific needs.

For improved maneuverability, the Craftsman 917.273062 features a tight turning radius, enabling users to navigate around obstacles such as trees, flower beds, and garden fixtures with ease. This is particularly advantageous for homeowners with intricate landscapes. The riding mower is also designed with a comfortable, high-back seat, which is ergonomically shaped to provide support and reduce fatigue during prolonged use.

Technologically, the mower includes a user-friendly dashboard that displays essential information, such as fuel level, speed settings, and maintenance reminders. This intuitive interface simplifies operation and helps users manage their mowing tasks effectively.

Another characteristic of the Craftsman 917.273062 is its ease of maintenance. The mower features an accessible cutting deck that makes it simple to clean and maintain the blades, ensuring optimal performance over time. Additionally, the mower is equipped with a fuel-efficient system, reducing the frequency of refueling and minimizing environmental impact.

In summary, the Craftsman 917.273062 combines power, efficiency, and user-friendly design to provide a superior mowing experience. Its combination of a robust engine, versatile cutting deck, ergonomic design, and ease of maintenance makes it a preferred choice for homeowners and landscape enthusiasts alike. Whether for routine lawn care or tackling overgrown areas, the Craftsman 917.273062 proves to be a reliable and effective solution.
Top Page Image Contents