Craftsman 917.273062 owner manual To Replace Mower Drive Belt, Mower Drive Belt Removal

Page 25

o If adjustment is necessary, make adjustment on one side of mower only.

,,To raise one side of mower, tighten lift

link adjustment nut on that side.

• To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16". e Recheck measurements after adjust-

ing.

Bottom Edge of

Bottom Edge of

Mower to Ground

Mower to Ground

_F _

Both Front Links Should be Equal in Length

Nut

_G _

 

FRONT-TO-BACK ADJUSTMENT iMPORTANT: Deck must be level side-to- side. If the following front-to-back adjustment is necessary, be sure to adjust

both front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance "F" directly in front of and behind the mandrel at bottom edge of mower housing as shown.

*Before making any necessary adjust- ments, check that both front links are

equal in length.

=If links are not equal in length, adjust one link to same length as other link.

. To lower front of mower housing, loosen nut "G" on both front links an

equal number of turns.

,When distance "F" is 1/8" to 1/2" lower at front than rear, tighten nut "H"

against trunnion on both front links.

°To raise front of mower housing, loosen nut "H" from trunnion on both front links.

Tighten nut "G" on both front links an

equal number of turns.

. When distance "F" is 1/8" to 1/2" lower at front than rear, tighten nut "H"

against trunnion on both front links. NOTE: Each full turn of nut"G" will

change dim. "F" by approximately 3/8".

*Recheck side-to-side adjustment.

Front Links

TO REPLACE MOWER DRIVE BELT

MOWER DRIVE BELT REMOVAL

1.Park tractor on a level surface. Engage parking brake.

2.Remove screws from L.H. mandrel cover and remove cover.

3.Roll belt over the top of L.H. mandrel pulley.

4.Remove belt from electric clutch pulley.

5.Remove belt from idler pulleys.

6.Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

7.Check primary idler arm and two idlers to see that they rotate freely.

8.Be sure spring is securely hooked to primary idler arm and bolt in mower housing.

MOWER DRIVE BELT INSTALLATION

9.Install belt in both idlers. Make sure

belt is in both belt keepers at the idlers as shown.

10.Install new belt onto electric clutch pulley.

11.Roll belt into upper groove of L.H.

mandrel pulley.

12.Carefu!ly check belt routing making sure belt is in the grooves correctly and inside belt keepers.

13.Reassemble L.H. mandrel cover.

25

Image 25
Contents Icraftsmani Limited 90 DAY Warranty on Battery Limitedtwo Yearwarranty on Craftsman Riding Equipm ENT PartsI1.SLOPE Operation General OperationDo not Ill. Children Page Repair Agreement Product SpecificationsCustomer Responsibilities Seat To Remove Tractor from Tools Required for AssemblyUnpack Carton Check Battery HOW to SET UP Your TractorInstall Seat Before Removing Tractor from SkidPage Install Mower and Drive Belt Checktire Pressure ChecklistCheck Mower Levelness Check for Proper Position ALL BeltsClutch Disengaged Know Your Tractor To SET Parking Brake HOW to USE Your TractorTo Move Forward Backward To Operate Mower To Adjust Gauge WheelsTo Operate on Hills Ments Before Starting the EngineAutomatic Transmission Warm UP To Start EnginePurge Transmission Mowing Tips General Recommendations Lubrication ChartBefore Each USE Operator Presence System BatteryBlade Removal Lubrication EngineCleaning Clean AIR ScreenEngine OIL Filter MufflerTo Level Mower Housing To Install MowerSIDE-TO-SIDE Adjustment To Remove MowerTo Replace Mower Drive Belt Mower Drive Belt InstallationMower Drive Belt Removal To Replace Mower Blade Drive Belt To Adjust Attachment ClutchTo Replace Mower Drive Belt Belt Installation To Adjust BrakeBelt Removal To Adjust Steering Wheel Alignment To Adjust Motion Control LeverFront Wheel TOE-INADJUSTMENT Transmission REMOVAL/REPLACE- MentReplacing Battery To Start Engine with a Weak BatteryTo Remove Wheel for Repairs To Replace Headlight Bulb To Adjust Attachment Lift SpringTo Remove Hood and Grill AS Sembly To Adjust Carburetor To Adjust Choke ControlPreliminary Setting Final SettingOther BatteryFuel System Engine OILCorrection Problem CauseChart Troubleshooting ProblemCause Correction Troubleshooting ChartFast SlowPage ELECTa£CkuzcH Schematic Tractor Model Number 917,273062Tractor -- Model Number Electrical KEY Part Description Tractor --MODEL Number ElectricalTractor Model Number 917.273062 Chassis and Enclosures Description Tractor --MODEL Number Chassis and EnclosuresTractor Model Number Ground Drive UNC Tractor --MODEL Number Ground DriveTractor Model Number Steering Steering Tractor -- Model NumberSpark Arrester KIT Tractor Model Number EngineKEY Part EngineKEY Part NO. NO. Description Tractor --MODEL Number Seat AssemblyWheels and Tires Tractor Model NumberDecals Tractor -- Model Number Lift Assembly KEY Part NO. NO,DESCRIPTION Tractor Model Number Mower Deck KEY Part NO. NO.DESCRIPTION Tractor --MODEL Number Mower Deck111 KEY Part Description Tractor --MODEL Number TRANSAXLE--MODEL Number 222-3010L144569 Shaft Pump 127148X Swashplate Ylinder HEAD, Valve and Breatherj IGNITION/ELECTRICALJ Blower Housing and Bafflesj Tractor =-MODEL Number Exhaustj HEAD/VALVE/BREATHER Crankcase KEY Part Kohler ENGINE-MODEL Number CV20S, Type Number Tractor --MODEL NUM BERKEY Part NO. NO.DESCRIPTION TRACTOR-- Model NUM BERKohler ENGINE-MODEL Number CV20S, Type Number Page Page Suggested Guide for Sighting Slopes for Safe Operation Get it fixed, at your home or ours

917.273062 specifications

The Craftsman 917.273062 is a high-performance riding lawn mower designed for residential and light commercial use, blending efficiency, power, and ease of operation. This robust machine is ideal for users seeking to maintain larger lawns or properties with varying terrains.

One of the standout features of the Craftsman 917.273062 is its powerful engine. Equipped with a 19.5 horsepower Briggs & Stratton engine, this mower delivers reliable performance, offering ample power to handle thick grass and uneven surfaces. The engine's design ensures smooth operation with reduced noise levels, making mowing more pleasant.

The mower features a 42-inch cutting deck, allowing it to cover vast areas in a single pass. This deck design incorporates a twin-blade system, which enhances cutting efficiency and provides a clean, even cut. The adjustable cutting heights, ranging from 1.5 inches to 4 inches, allow users to customize their mowing experience based on their lawn's specific needs.

For improved maneuverability, the Craftsman 917.273062 features a tight turning radius, enabling users to navigate around obstacles such as trees, flower beds, and garden fixtures with ease. This is particularly advantageous for homeowners with intricate landscapes. The riding mower is also designed with a comfortable, high-back seat, which is ergonomically shaped to provide support and reduce fatigue during prolonged use.

Technologically, the mower includes a user-friendly dashboard that displays essential information, such as fuel level, speed settings, and maintenance reminders. This intuitive interface simplifies operation and helps users manage their mowing tasks effectively.

Another characteristic of the Craftsman 917.273062 is its ease of maintenance. The mower features an accessible cutting deck that makes it simple to clean and maintain the blades, ensuring optimal performance over time. Additionally, the mower is equipped with a fuel-efficient system, reducing the frequency of refueling and minimizing environmental impact.

In summary, the Craftsman 917.273062 combines power, efficiency, and user-friendly design to provide a superior mowing experience. Its combination of a robust engine, versatile cutting deck, ergonomic design, and ease of maintenance makes it a preferred choice for homeowners and landscape enthusiasts alike. Whether for routine lawn care or tackling overgrown areas, the Craftsman 917.273062 proves to be a reliable and effective solution.