Craftsman 917.27499 HOW to Useyourtractor To SET Parking Brake, Stopping, To USE Choke Control

Page 14

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

HOW TO USEYOURTRACTOR

TO SET PARKING BRAKE

Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.

1.Depress clutch/brake pedal into full "BRAKE" position and hold.

2.Place parking brake lever in "EN-

GAGED" position and release pressure from clutch/brake pedal. Pedal should remain in "BRAKE" position. Make sure parking brake wil_ hold tractor secure.

Push-Into

AttachmentClutch

Choke "

SwitchPullOut To

 

 

Key

 

 

Brake

 

 

"Engaged"

Brake Peda

Posit]on

"Drive"

Position

Gear Shift

Posit]on

Adjustment Knob

Lever

 

 

STOPPING

MOWER BLADES -

TO stop mower blades, move attach- ment clutch switch to "DISENGAGED"

position.

GROUND DRWE -

To stop ground ddve, depress clutch/ brake pedal into full =BRAKE" position.

Move gearshift lever to neutral (N) position.

ENGINE -

Move throttle control to slow position.

NOTE: Failure to move throttle control to slow position and allowing engine to idle before stopping may cause engine to "backfire".

Turn ignition key to "OFF" position end remove key. Always remove key when leaving tractor to prevent unauthorized use.

Never use choke to stop engine.

IMPORTANT: Leaving the ignition switch in any position other than "OFF" will cause the battery to be discharged,

(dead).

NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause "browning" of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

I,CAUTION: Always stop tractor completely, as described above, before leaving the operator's position; to empty grass catcher, etc.

TO USE THROTTLE CONTROL

Always operate engine at full throttle.

Operating engine at less than full throttle reduces the battery charging rate.

Full throttle otters the best mower performance.

TO USE CHOKE CONTROL

Use choke control whenever you are starting a cold engine. Do not use to start a warm engine.

To engage choke control, pull knob out.

Slowly push knob in to disengage.

TO MOVE FORWARD AND BACK- WARD

The direction and speed of movement is controlled by the gearshift lever.

1.Start tractor with clutch/brake pedal depressed and gearshift lever in neutral (N) position.

2.Move gearshift and range shift levers to desired position.

3.Slowly release clutch/brake peda_ to start movement.

IMPORTANT: Bring tractor to a complete stop before shifting or changing gears. Failure to do so will shorten the useful life

of your transaxle.

TO ADJUST MOWER CU'I-rlNG HEIGHT

The cutting height is controlled by turning the height adjustment knob in desired direction.

Turn knob c_ockwise((_) to raise cutting height.

Turn knob counterclockwise (=,_)to

14 lower cutting height.

Image 14
Contents Icraftsmawi Limited 90 DAY Warranty on Battery While on the slope Follow the manufacturersrecommenda General OperationII. Slope Operation Stabilityof the machineMachine. Tall grass can hide obstacles IV. ServiceNl. Children Tragic accidents can occur if the operator Safety is Involved Wash hands after handlingReverse Product Specifications Gasoline 3.5 GallonsRC12YC Ground Speed FrontSeat MowerTo Remove Tractor from Carton Unpack Carton Tools Required for AssemblyHOW to SET UP Your Tractor Before Removing Tractor from SkidPacking and set aside for assembly of seat to tractor Install SeatAdjust seat before tightening adjustment knob Check Tire Pressure Install Mower and Drive BeltMower suspension Shoder Bolt WheelFor best cutting results, mower should be ChecklistCheck Mower Levelness Check for Proper Position of ALL BeltsNEOENG. ...OFFO,L.RESSUeLIG..SOO%..P T Attachment Reverse Neutral Highlow Clutch EngagedOur tractors conform to the safety standards Knowyour TractorTo USE Choke Control HOW to Useyourtractor To SET Parking BrakeStopping To Move Forward and BACK- WardTo Operate on Hills To Adjust Gauge WheelsTo Operate Mower To TransportBefore Starting the Engine Check Engine OIL Level Towing Carts and Other AI-rACHMents ADD GasolineMowing Tips = Always operate engine at full throttleBefore Each USE Lubrication ChartGeneral Recommendations Tires BatteryBrake Operation Operator Presence SystemEngine Lubrication BeltsCheck Transaxle OIL Level To Service PRE.CLEANER Clean AIR ScreenClean AIR INTAKE/COOLING Areas CleaningSIDE-TO-SIDE Adjustment To Install MowerTo Level Mower Housing TractorBoth Front Links Must be Equal Length Recheck side-to-side adjustmentMower Drive Belt Installation Mower Drive Belt RemovalTo Replace Mower Blade Drive Belt Install Mower and DriveTo Adjust Brake Sears or other qualified service center Belt InstallationTo Adjust Steering Wheel ALIGN- Ment DePulle KeeperReplacing BAI-IERY To Remove Wheel for Repairs Front WheelRear Wheel To Replace Fuse To Replace Headlight BulbInterlocks and Relays To Remove Hood and Grill AS SemblyFinal Setiing To Adjust Choke ControlTo Adjust Carburetor Acceleration TestEngineoil TractorEngine Fuelsystem CylindersProblem Cause CorrectionTroubleshooting Chart CauseLight switch Mower drive belt worn Blades improperly installedTurn switch on Check wiring and connecTtAGTOP.oDEL HU6-P9Lt,14990 Tractor - Model Number ElectricalTractor - Model NUM BER KEY Part NO, no DescriptionTRACTOR--MODELNUMBER917.274990 Chassisandenclosures KEY Part Description TRACTOR- -MODEL Number Chassis and EnclosuresKEY Part NO. no TRACTOR- Model Numb ER Ground Drive TRACTOR- Model NUM BER Ground Drive KEY Part DescriptionTRACTOR- Model Numb ER Steeringassembly TRACTOR- Model NUM BER Steeringassembly Spark Arrester KIT Tractor - Model Numb ER 917,274990 TRACTOR- Model Numb ER Seat Assembly KEY Part NO. NO.DESCRIPTIONWheels & Tires TRACTOR-- Model NumberDecals IEY Part DescriptionLift Assembly TRACTOR- Model Number Lift Assembly KEY PartTransaxle Nut 3/8-24 42GORCylinder HEAD, Valve and Breather HEAD/VALVE/BREATHER CrankcasePage Blower Housing & Baffles IGNITION/CHARGING KEY Part NO. NO.DESCRIPTIONStarting System Starting System OIL PAN/LUB Rication KEY Part DescriptionCranksha TRACTOR- Model Number Fuel System KEY Part NO. noPage Suggested Guide for Sighting Slopes for Safe Operation 1X-5,33-6937 179079 04.09.01 RH

917.27499 specifications

The Craftsman 917.27499 is a versatile and powerful riding lawn mower designed to provide optimum cutting performance and enhance the overall mowing experience. Known for its robust construction and innovative features, this mower is ideal for homeowners with medium to large yards, ensuring efficient grass management with ease.

One of the main features of the Craftsman 917.27499 is its reliable 19 horsepower Briggs & Stratton engine. This powerful engine offers ample torque and speed, enabling the mower to tackle thick grasses and uneven terrains with relative ease. The mower's automatic transmission allows for smooth acceleration and deceleration without the need for manual gear shifting, providing a user-friendly operation.

The cutting deck of the Craftsman 917.27499 is another standout feature. With a 42-inch cutting width, it allows for quick and efficient mowing, reducing the number of passes needed to cover large areas. The deck is made from durable steel to withstand the rigors of regular use, and it offers three adjustable cutting heights, enabling users to customize the mowing experience according to the grass type and height.

Ergonomics also play a significant role in the design of this mower. The comfortable, adjustable seat ensures that users can have an optimal riding position, reducing fatigue during lengthy mowing sessions. Additionally, the steering wheel is designed for ease of handling, providing accurate control and maneuverability in tight spaces around obstacles like trees and flower beds.

Another remarkable aspect of the Craftsman 917.27499 is its enhanced technology features. It includes an easy-to-use control panel that allows users to manage the mower’s functions seamlessly. Furthermore, the mower's maintenance features, such as the quick-change blade system, facilitate easy blade replacement, promoting consistent cutting performance.

Safety is paramount with the Craftsman brand, and the 917.27499 includes several safety features. The mower is equipped with a safety switch that automatically shuts off the engine if the operator leaves the seat, preventing any accidents during operation.

In summary, the Craftsman 917.27499 is a powerful, reliable, and user-friendly riding lawn mower that combines advanced technologies with robust performance. Its key features, ergonomic design, and safety mechanisms make it an excellent option for homeowners seeking efficiency and ease of use in lawn care. Whether navigating tight corners or managing larger expanses of grass, the Craftsman 917.27499 excels in delivering a well-manicured lawn with minimal effort.