Craftsman 917.27499 To Replace Mower Blade Drive Belt, Install Mower and Drive, To Adjust Brake

Page 24

L,H.

Screws

Electric

Mandrel

Idler

Clutch

 

 

Pulley

Bolt in

Mandrel

Mower

D(hte Belt

Belt

Keepers

TO REPLACE MOWER BLADE DRIVE BELT

Pork the tractor on level surface. Engage parking brake.

1.Remove mower drive belt (See "TO REPLACE MOWER DRIVE BELT" in this section of this manual).

2.Remove mower (See "TO REMOVE

MOWER" in this section of this manual).

3.Remove screws from R.H. mandrel cover and remove cover. Unhook spring from bolt on mower housing.

4.Carefully roll belt off R,H. mandrel pulley.

5.Remove belt from center mandrel

pulley, idler pulley, and L.H. mandrel pulley.

6.Remove any dirt or grass which may have accumulated around mandrels and entire upper deck surface.

7.Check secondary idler arm and idler to see that they rotate freely.

8.Be sure spring is hooked in secondary idler arm and sway-barbracket.

9.Install new belt in lower groove of L.H. mandrel pulley, idler pulley, and center mandrel pulley as shown.

10.Roll belt over R.H. mandrel pulley. Make sure belt is in all grooves properly.

11.Reconnect spring to bolt in mower housing and reinstall R.H. mandrel cover.

12.Reinstall mower to tractor (See

"INSTALL MOWER AND DRIVE

BELT" in the Assembly section of this monual).

Reassemble mower drive belt (See

,,TO REPLACE MOWER DRIVE BELT" in this section of this manual).

 

MowerBlade

 

 

 

L.H,

Drive Belt

Center

 

 

Mandrel_f._-.._\

Maln_el R.H. Mandrel

 

:er

 

 

 

Secon_

 

 

 

Idler Arm _

(__[1_'_<_

 

_J

 

SrwaYkBtar id_r_/

//

\

 

 

Pulley

 

 

TO ADJUST ATrACHMENT CLUTCH

The electric clutch should provide years of service. The clutch has a built-inbrake

that stops the puUeywithin 5 seconds. Eventually, the internal brake will wear which may cause the mower blades to not engage, or, to not stop as required.

Adjustments should be made by a Sears

or other qualified service center.

1, Make sure attachment clutch and

ignition switches are in "OFF" position.

2.Adjust the three nylon Iocknuts until space between clutch plate and rotor measures .012" at all three slot

locations cut in the side of brake plata. NOTE: After installing a new electric clutch, run tractor at full throttle and engage and disengage electric clutch 10 cycles to wear in clutch plate.

/Rotor

cotehP Ot2

Nylon_ __

 

Loeknut(3_

B"_rake

_--_.

Plate

TO ADJUST BRAKE

Your tractor is equipped with an adjustable brake systemwhich is mounted on the left side of the transaxfe.

If tractorrequires more than six (6) feet stoppingdistance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

1.Depress clutch/Drake pedal and engage parking brake.

2.Measure distance between brake operating arm and nut "A" on brake rod.

3.If distance is other than 1-3/4", loosen jam nut and turn nut "A" until distance becomes 1-3/4". Retighten jam nut against nut "A".

24

Image 24
Contents Icraftsmawi Limited 90 DAY Warranty on Battery General Operation II. Slope OperationWhile on the slope Follow the manufacturersrecommenda Stabilityof the machineIV. Service Nl. Children Tragic accidents can occur if the operatorMachine. Tall grass can hide obstacles Safety is Involved Wash hands after handlingProduct Specifications Gasoline 3.5 Gallons RC12YC Ground SpeedReverse FrontSeat MowerTools Required for Assembly HOW to SET UP Your TractorTo Remove Tractor from Carton Unpack Carton Before Removing Tractor from SkidInstall Seat Adjust seat before tightening adjustment knobPacking and set aside for assembly of seat to tractor Install Mower and Drive Belt Mower suspensionCheck Tire Pressure Shoder Bolt WheelChecklist Check Mower LevelnessFor best cutting results, mower should be Check for Proper Position of ALL BeltsNEOENG. ...OFFO,L.RESSUeLIG..SOO%..P T Attachment Reverse Neutral Highlow Clutch EngagedOur tractors conform to the safety standards Knowyour TractorHOW to Useyourtractor To SET Parking Brake StoppingTo USE Choke Control To Move Forward and BACK- WardTo Adjust Gauge Wheels To Operate MowerTo Operate on Hills To TransportTowing Carts and Other AI-rACH MentsBefore Starting the Engine Check Engine OIL Level ADD GasolineMowing Tips = Always operate engine at full throttleLubrication Chart General RecommendationsBefore Each USE Battery Brake OperationTires Operator Presence SystemBelts Check Transaxle OIL LevelEngine Lubrication Clean AIR Screen Clean AIR INTAKE/COOLING AreasTo Service PRE.CLEANER CleaningTo Install Mower To Level Mower HousingSIDE-TO-SIDE Adjustment TractorRecheck side-to-side adjustment Mower Drive Belt InstallationBoth Front Links Must be Equal Length Mower Drive Belt RemovalInstall Mower and Drive To Adjust BrakeTo Replace Mower Blade Drive Belt Belt Installation To Adjust Steering Wheel ALIGN- MentSears or other qualified service center DePulle KeeperTo Remove Wheel for Repairs Front Wheel Rear WheelReplacing BAI-IERY To Replace Headlight Bulb Interlocks and RelaysTo Replace Fuse To Remove Hood and Grill AS SemblyTo Adjust Choke Control To Adjust CarburetorFinal Setiing Acceleration TestTractor Engine FuelsystemEngineoil CylindersProblem Cause CorrectionTroubleshooting Chart CauseMower drive belt worn Blades improperly installed Turn switch onLight switch Check wiring and connecTtAGTOP.oDEL HU6-P9Lt,14990 Tractor - Model Number ElectricalTractor - Model NUM BER KEY Part NO, no DescriptionTRACTOR--MODELNUMBER917.274990 Chassisandenclosures TRACTOR- -MODEL Number Chassis and Enclosures KEY Part NO. noKEY Part Description TRACTOR- Model Numb ER Ground Drive TRACTOR- Model NUM BER Ground Drive KEY Part DescriptionTRACTOR- Model Numb ER Steeringassembly TRACTOR- Model NUM BER Steeringassembly Spark Arrester KIT Tractor - Model Numb ER 917,274990 TRACTOR- Model Numb ER Seat Assembly KEY Part NO. NO.DESCRIPTIONTRACTOR-- Model Number DecalsWheels & Tires IEY Part DescriptionLift Assembly TRACTOR- Model Number Lift Assembly KEY PartTransaxle Nut 3/8-24 42GORCylinder HEAD, Valve and Breather HEAD/VALVE/BREATHER CrankcasePage Blower Housing & Baffles IGNITION/CHARGING KEY Part NO. NO.DESCRIPTIONStarting System Starting System OIL PAN/LUB Rication KEY Part DescriptionCranksha TRACTOR- Model Number Fuel System KEY Part NO. noPage Suggested Guide for Sighting Slopes for Safe Operation 1X-5,33-6937 179079 04.09.01 RH

917.27499 specifications

The Craftsman 917.27499 is a versatile and powerful riding lawn mower designed to provide optimum cutting performance and enhance the overall mowing experience. Known for its robust construction and innovative features, this mower is ideal for homeowners with medium to large yards, ensuring efficient grass management with ease.

One of the main features of the Craftsman 917.27499 is its reliable 19 horsepower Briggs & Stratton engine. This powerful engine offers ample torque and speed, enabling the mower to tackle thick grasses and uneven terrains with relative ease. The mower's automatic transmission allows for smooth acceleration and deceleration without the need for manual gear shifting, providing a user-friendly operation.

The cutting deck of the Craftsman 917.27499 is another standout feature. With a 42-inch cutting width, it allows for quick and efficient mowing, reducing the number of passes needed to cover large areas. The deck is made from durable steel to withstand the rigors of regular use, and it offers three adjustable cutting heights, enabling users to customize the mowing experience according to the grass type and height.

Ergonomics also play a significant role in the design of this mower. The comfortable, adjustable seat ensures that users can have an optimal riding position, reducing fatigue during lengthy mowing sessions. Additionally, the steering wheel is designed for ease of handling, providing accurate control and maneuverability in tight spaces around obstacles like trees and flower beds.

Another remarkable aspect of the Craftsman 917.27499 is its enhanced technology features. It includes an easy-to-use control panel that allows users to manage the mower’s functions seamlessly. Furthermore, the mower's maintenance features, such as the quick-change blade system, facilitate easy blade replacement, promoting consistent cutting performance.

Safety is paramount with the Craftsman brand, and the 917.27499 includes several safety features. The mower is equipped with a safety switch that automatically shuts off the engine if the operator leaves the seat, preventing any accidents during operation.

In summary, the Craftsman 917.27499 is a powerful, reliable, and user-friendly riding lawn mower that combines advanced technologies with robust performance. Its key features, ergonomic design, and safety mechanisms make it an excellent option for homeowners seeking efficiency and ease of use in lawn care. Whether navigating tight corners or managing larger expanses of grass, the Craftsman 917.27499 excels in delivering a well-manicured lawn with minimal effort.