Craftsman 917.27499 manual Clean AIR Screen, Clean AIR INTAKE/COOLING Areas, AIR Filter, Muffler

Page 21

CLEAN AIR SCREEN

Air screen must be kept free of dirt and

Foam

Cartridge

chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.

CLEAN AIR INTAKE/COOLING AREAS

To insure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times.

Every 100 hours of operer=on(more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds. Clean the cooling fins and external surfaces as necessary.

Make sure the cooling shrouds are reinstalled,

NOTE: Operating the engine with a blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed will cause engine damage due to overheating.

AIR FILTER

Your engine will not run properly using a dirty air filter. Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or every season, whichever occurs first.

Service air cleaner more often under

dusty conditions.

1. Loosen knob and remove cover.

TO SERVICE PRE.CLEANER

2.Slide foam pre-eleaneroff cartridge.

3.Wash it in liquid detergent and water.

4.Squeeze it dry in a clean cloth. Allow it to dry.

5.Saturate it in engine oil. Wrap it in clean, absorbent cloth and squeeze to remove excess oil.

TO SERVICE CARTRIDGE

•Replace a dirty, bent, or damaged oartddge.

NOTE: Do not wash the paper cartridge or use pressurized air, as this will damage the cartridge.

6, Remove nut and cartridge plate. 7, Reinstall the pre-cleaner (cleaned

and oiled) over the paper cartridge. 8, Check rubber seal for damage and

proper position around stud. Replace if necessary.

9.Reassemble air cleaner, cartridge plate, and nut.

10.Reinstall air cleaner cover and secure by tightening knob.

Pre-Cleaner

Cartridge

Rubber

Se_

Nut

ENGINE OIL FILTER

Replace the engine oil tilter every season or every other oil change if the tractor is used more than 100 hours in one year.

MUFFLER

Inspect and replace corroded muffler and spark arrester (it equipped) as it could create a fire hazard and/or damage.

SPARK PLUGS

Replace spark plugs at the beginning of each mowing season or after every 100 hours ot operation, whichever occurs first.

Spark plu,,g,type and gap setting are shown in 'PRODUCT SPECIFICATIONS"

section of this manual

IN-LINE FUEL FILTER

The fuel filter should be replaced once each season. It fuel filter becomes

clogged, obstructing fuel flow to carbure- tor, replacement is required.

1.With engine cool, remove filter and plug fuel line sections.

2.Place new fuel fitter in position in fuel

line with arrow pointing towards carburetor.

3.Be sure there are no fuel line leaks and clamps are propedy positioned.

4.Immediately wipe up any spillod gasoline.

Fuel Nlter_

CLEANING

•Clean engine, battery, seat, finish, etc. of all foreign matter.

•Keep finished surfaces and wheels free of all gasoline, oil, etc.

•Protect painted surfaces with automo- tive type wax.

We do not recommend using a garden hose to clean your tractor unless the electrical system, muffler, air filter and carburetor are covered to keep water out.

Water in engine can result in a shortened

21 engine life.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Icraftsmawi Limited 90 DAY Warranty on Battery II. Slope Operation General OperationWhile on the slope Follow the manufacturersrecommenda Stabilityof the machineIV. Service Nl. Children Tragic accidents can occur if the operatorMachine. Tall grass can hide obstacles Wash hands after handling Safety is InvolvedRC12YC Ground Speed Product Specifications Gasoline 3.5 GallonsReverse FrontMower SeatHOW to SET UP Your Tractor Tools Required for AssemblyTo Remove Tractor from Carton Unpack Carton Before Removing Tractor from SkidInstall Seat Adjust seat before tightening adjustment knobPacking and set aside for assembly of seat to tractor Mower suspension Install Mower and Drive BeltCheck Tire Pressure Shoder Bolt WheelCheck Mower Levelness ChecklistFor best cutting results, mower should be Check for Proper Position of ALL BeltsAttachment Reverse Neutral Highlow Clutch Engaged NEOENG. ...OFFO,L.RESSUeLIG..SOO%..P TKnowyour Tractor Our tractors conform to the safety standardsStopping HOW to Useyourtractor To SET Parking BrakeTo USE Choke Control To Move Forward and BACK- WardTo Operate Mower To Adjust Gauge WheelsTo Operate on Hills To TransportMents Towing Carts and Other AI-rACHBefore Starting the Engine Check Engine OIL Level ADD Gasoline= Always operate engine at full throttle Mowing TipsLubrication Chart General RecommendationsBefore Each USE Brake Operation BatteryTires Operator Presence SystemBelts Check Transaxle OIL LevelEngine Lubrication Clean AIR INTAKE/COOLING Areas Clean AIR ScreenTo Service PRE.CLEANER CleaningTo Level Mower Housing To Install MowerSIDE-TO-SIDE Adjustment TractorMower Drive Belt Installation Recheck side-to-side adjustmentBoth Front Links Must be Equal Length Mower Drive Belt RemovalInstall Mower and Drive To Adjust BrakeTo Replace Mower Blade Drive Belt To Adjust Steering Wheel ALIGN- Ment Belt InstallationSears or other qualified service center DePulle KeeperTo Remove Wheel for Repairs Front Wheel Rear WheelReplacing BAI-IERY Interlocks and Relays To Replace Headlight BulbTo Replace Fuse To Remove Hood and Grill AS SemblyTo Adjust Carburetor To Adjust Choke ControlFinal Setiing Acceleration TestEngine Fuelsystem TractorEngineoil CylindersCause Correction ProblemCause Troubleshooting ChartTurn switch on Mower drive belt worn Blades improperly installedLight switch Check wiring and connecTtAGTOP.oDEL HU6-P9Lt,14990 Electrical Tractor - Model NumberKEY Part NO, no Description Tractor - Model NUM BERTRACTOR--MODELNUMBER917.274990 Chassisandenclosures TRACTOR- -MODEL Number Chassis and Enclosures KEY Part NO. noKEY Part Description TRACTOR- Model Numb ER Ground Drive KEY Part Description TRACTOR- Model NUM BER Ground DriveTRACTOR- Model Numb ER Steeringassembly TRACTOR- Model NUM BER Steeringassembly Spark Arrester KIT Tractor - Model Numb ER 917,274990 KEY Part NO. NO.DESCRIPTION TRACTOR- Model Numb ER Seat AssemblyDecals TRACTOR-- Model NumberWheels & Tires IEY Part DescriptionLift Assembly KEY Part TRACTOR- Model Number Lift AssemblyTransaxle 42GOR Nut 3/8-24Cylinder HEAD, Valve and Breather Crankcase HEAD/VALVE/BREATHERPage IGNITION/CHARGING KEY Part NO. NO.DESCRIPTION Blower Housing & BafflesStarting System OIL PAN/LUB Rication KEY Part Description Starting SystemCranksha Fuel System KEY Part NO. no TRACTOR- Model NumberPage Suggested Guide for Sighting Slopes for Safe Operation 179079 04.09.01 RH 1X-5,33-6937

917.27499 specifications

The Craftsman 917.27499 is a versatile and powerful riding lawn mower designed to provide optimum cutting performance and enhance the overall mowing experience. Known for its robust construction and innovative features, this mower is ideal for homeowners with medium to large yards, ensuring efficient grass management with ease.

One of the main features of the Craftsman 917.27499 is its reliable 19 horsepower Briggs & Stratton engine. This powerful engine offers ample torque and speed, enabling the mower to tackle thick grasses and uneven terrains with relative ease. The mower's automatic transmission allows for smooth acceleration and deceleration without the need for manual gear shifting, providing a user-friendly operation.

The cutting deck of the Craftsman 917.27499 is another standout feature. With a 42-inch cutting width, it allows for quick and efficient mowing, reducing the number of passes needed to cover large areas. The deck is made from durable steel to withstand the rigors of regular use, and it offers three adjustable cutting heights, enabling users to customize the mowing experience according to the grass type and height.

Ergonomics also play a significant role in the design of this mower. The comfortable, adjustable seat ensures that users can have an optimal riding position, reducing fatigue during lengthy mowing sessions. Additionally, the steering wheel is designed for ease of handling, providing accurate control and maneuverability in tight spaces around obstacles like trees and flower beds.

Another remarkable aspect of the Craftsman 917.27499 is its enhanced technology features. It includes an easy-to-use control panel that allows users to manage the mower’s functions seamlessly. Furthermore, the mower's maintenance features, such as the quick-change blade system, facilitate easy blade replacement, promoting consistent cutting performance.

Safety is paramount with the Craftsman brand, and the 917.27499 includes several safety features. The mower is equipped with a safety switch that automatically shuts off the engine if the operator leaves the seat, preventing any accidents during operation.

In summary, the Craftsman 917.27499 is a powerful, reliable, and user-friendly riding lawn mower that combines advanced technologies with robust performance. Its key features, ergonomic design, and safety mechanisms make it an excellent option for homeowners seeking efficiency and ease of use in lawn care. Whether navigating tight corners or managing larger expanses of grass, the Craftsman 917.27499 excels in delivering a well-manicured lawn with minimal effort.
Top Page Image Contents