Craftsman 917.27499 To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse, Engine

Page 27

Hex

Bolt

Guard

Cabte

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged v_dng may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring

diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 30 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO ADJUST A'I-rACHMENT LIFT SPRING

1.White holding spring bushing with wrench, loosen jam nut.

•Turn adjustment bolt clockwise to extend spring and reduce lift effort for heavier attachments.

•Turn adjustment bolt counterclockwise for lighter attachments.

2.Retighten jam nut against spring bushing.

IMPORTANT: Do not adjust for maximum spring tension when using tight attach- ments such as a mower. Adjust lift lever spring to aid in lifting attachment. Do not overpower spring. When removing attachment, always adjust spring tension to its lowest position.

Bushing

N_ _A_achment Uff

Spnng

TO REMOVE HOOD AND GRILL AS-

SEMBLY

1, Raise hood.

2, Unsnap headlight wire connector.

3, Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.To replace, reverse above procedure.

Headlight Wire

ENGINE

Maintenance, repair, or replecement of the emission control devices and sys- tems, which are being done at the customers expense, may be performed by any non-rood engine repair establish- ment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THRO'n'LECONTROL

CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as de- scribed below before loosening cable. If adjustment is necessary, proceed as follows:

1.With engine not running, move throttle control lever to fast position.

2.Check that speed control lever is against stop screw. If it is not, loosen casing clamp screw and pull throttle cable until lever is against screw.

Tighten clamp screw securely.

IdleFuelAdjusting Idle speedAdjusting Needle

Thro_le

Control

Cable

:hoke Control Cable

27ScreV_lamp

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Icraftsmawi Limited 90 DAY Warranty on Battery Stabilityof the machine General OperationII. Slope Operation While on the slope Follow the manufacturersrecommendaIV. Service Nl. Children Tragic accidents can occur if the operatorMachine. Tall grass can hide obstacles Wash hands after handling Safety is InvolvedFront Product Specifications Gasoline 3.5 GallonsRC12YC Ground Speed ReverseMower SeatBefore Removing Tractor from Skid Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from Carton Unpack CartonInstall Seat Adjust seat before tightening adjustment knobPacking and set aside for assembly of seat to tractor Shoder Bolt Wheel Install Mower and Drive BeltMower suspension Check Tire PressureCheck for Proper Position of ALL Belts ChecklistCheck Mower Levelness For best cutting results, mower should beAttachment Reverse Neutral Highlow Clutch Engaged NEOENG. ...OFFO,L.RESSUeLIG..SOO%..P TKnowyour Tractor Our tractors conform to the safety standardsTo Move Forward and BACK- Ward HOW to Useyourtractor To SET Parking BrakeStopping To USE Choke ControlTo Transport To Adjust Gauge WheelsTo Operate Mower To Operate on HillsADD Gasoline Towing Carts and Other AI-rACHMents Before Starting the Engine Check Engine OIL Level= Always operate engine at full throttle Mowing TipsLubrication Chart General RecommendationsBefore Each USE Operator Presence System BatteryBrake Operation TiresBelts Check Transaxle OIL LevelEngine Lubrication Cleaning Clean AIR ScreenClean AIR INTAKE/COOLING Areas To Service PRE.CLEANERTractor To Install MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentMower Drive Belt Removal Recheck side-to-side adjustmentMower Drive Belt Installation Both Front Links Must be Equal LengthInstall Mower and Drive To Adjust BrakeTo Replace Mower Blade Drive Belt DePulle Keeper Belt InstallationTo Adjust Steering Wheel ALIGN- Ment Sears or other qualified service centerTo Remove Wheel for Repairs Front Wheel Rear WheelReplacing BAI-IERY To Remove Hood and Grill AS Sembly To Replace Headlight BulbInterlocks and Relays To Replace FuseAcceleration Test To Adjust Choke ControlTo Adjust Carburetor Final SetiingCylinders TractorEngine Fuelsystem EngineoilCause Correction ProblemCause Troubleshooting ChartCheck wiring and connec Mower drive belt worn Blades improperly installedTurn switch on Light switchTtAGTOP.oDEL HU6-P9Lt,14990 Electrical Tractor - Model NumberKEY Part NO, no Description Tractor - Model NUM BERTRACTOR--MODELNUMBER917.274990 Chassisandenclosures TRACTOR- -MODEL Number Chassis and Enclosures KEY Part NO. noKEY Part Description TRACTOR- Model Numb ER Ground Drive KEY Part Description TRACTOR- Model NUM BER Ground DriveTRACTOR- Model Numb ER Steeringassembly TRACTOR- Model NUM BER Steeringassembly Spark Arrester KIT Tractor - Model Numb ER 917,274990 KEY Part NO. NO.DESCRIPTION TRACTOR- Model Numb ER Seat AssemblyIEY Part Description TRACTOR-- Model NumberDecals Wheels & TiresLift Assembly KEY Part TRACTOR- Model Number Lift AssemblyTransaxle 42GOR Nut 3/8-24Cylinder HEAD, Valve and Breather Crankcase HEAD/VALVE/BREATHERPage IGNITION/CHARGING KEY Part NO. NO.DESCRIPTION Blower Housing & BafflesStarting System OIL PAN/LUB Rication KEY Part Description Starting SystemCranksha Fuel System KEY Part NO. no TRACTOR- Model NumberPage Suggested Guide for Sighting Slopes for Safe Operation 179079 04.09.01 RH 1X-5,33-6937

917.27499 specifications

The Craftsman 917.27499 is a versatile and powerful riding lawn mower designed to provide optimum cutting performance and enhance the overall mowing experience. Known for its robust construction and innovative features, this mower is ideal for homeowners with medium to large yards, ensuring efficient grass management with ease.

One of the main features of the Craftsman 917.27499 is its reliable 19 horsepower Briggs & Stratton engine. This powerful engine offers ample torque and speed, enabling the mower to tackle thick grasses and uneven terrains with relative ease. The mower's automatic transmission allows for smooth acceleration and deceleration without the need for manual gear shifting, providing a user-friendly operation.

The cutting deck of the Craftsman 917.27499 is another standout feature. With a 42-inch cutting width, it allows for quick and efficient mowing, reducing the number of passes needed to cover large areas. The deck is made from durable steel to withstand the rigors of regular use, and it offers three adjustable cutting heights, enabling users to customize the mowing experience according to the grass type and height.

Ergonomics also play a significant role in the design of this mower. The comfortable, adjustable seat ensures that users can have an optimal riding position, reducing fatigue during lengthy mowing sessions. Additionally, the steering wheel is designed for ease of handling, providing accurate control and maneuverability in tight spaces around obstacles like trees and flower beds.

Another remarkable aspect of the Craftsman 917.27499 is its enhanced technology features. It includes an easy-to-use control panel that allows users to manage the mower’s functions seamlessly. Furthermore, the mower's maintenance features, such as the quick-change blade system, facilitate easy blade replacement, promoting consistent cutting performance.

Safety is paramount with the Craftsman brand, and the 917.27499 includes several safety features. The mower is equipped with a safety switch that automatically shuts off the engine if the operator leaves the seat, preventing any accidents during operation.

In summary, the Craftsman 917.27499 is a powerful, reliable, and user-friendly riding lawn mower that combines advanced technologies with robust performance. Its key features, ergonomic design, and safety mechanisms make it an excellent option for homeowners seeking efficiency and ease of use in lawn care. Whether navigating tight corners or managing larger expanses of grass, the Craftsman 917.27499 excels in delivering a well-manicured lawn with minimal effort.
Top Page Image Contents