Craftsman 917.270962 owner manual To Operate Mower, To Adjust Gauge Wheels, To Operate on Hills

Page 14

The cutting height range is approxi- mately 1-1/2" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height

of grass and types of grass being mowed.

•The average lawn should be cut to

approximately 2-1/2 inches during the cool season and to over 3 inches

during hot months. For healthier and better looking lawns, mow o_ten and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut

relatively high; the second to desired height.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disen- gage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield place.

Attachment Clutch Lever "Engaged"

Positiont Lift

Lever High

Position

":::_Low

Position

TO ADJUST GAUGE WHEELS

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper

position to help prevent scalping in most terrain conditions.

•Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See "TO ADJUST MOWER CUTTING HEIGHT" in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/ 8 washer, and 3/8-16 Iocknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

3/8-16

 

Locknut_

 

Gauge

 

Wheel

 

Mounting

 

Bracket

 

3/8

;houlder

Gauge Wheet

Bolt

 

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

Position

Shield

TO OPERATE ON HILLS

_1_CAUTION: Do not drive up or down hills with slopes greater than 15 ° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to

brake position and engage parking brake.

•Move motion control lever to neutral

(N) position.

IMPORTANT: The motion control lever does not return to neutral (N) position when the clutch/brake pedal is de- pressed.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheel-

ing position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Sears Craftsman Help Line Am 5 pm, Mon SatProduct Limited TWO Year Warranty on Craftsman Riding EquipmentLimited 90 DAY Warranty on Battery SEARS, Roebuck and CO., D1817 WA, Hoffman ESTATES, ILBlades and proceed slowly straight ServiceSlope Operation Do notTor Customer Responsibilities Product SpecificationsMaintenance Agreement AboveAdapter Locknut 5/16-18Before Removing Tractor from Skid Attach Steering Wheel Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonShoulder Bolt Seat HOW to SET UP Your TractorCheck Battery To Drive Tractor OFF SkidCheck Deck Levelness Install Mulcher PlateCheck Tire Pressure ALL BeltsChecklist While Learning HOW to USE YourH L Free Wheel AdjustmentKnowyour Tractor Lift Lever Plunger Used toTo USE Throttle Control HOW to USE Your TractorTo SET Parking Brake To Move Forward and BACK- WardTo Operate on Hills To Adjust Gauge WheelsTo Operate Mower Towing Carts and Other Attachments AddgasolineTo Start Engine Before Starting the Enigne Check Engine OIL Level1CAUTION Never engage or disen Automatic Transmission Warm UPPurge Transmission Position. Shut- off engine and set parking brakeMowing Tips Mulching Mowing TipsBefore Each USE Lubrication ChartGeneral Recommendations Blade Care BatteryBrake Operation Blade RemovalClean AIR Screen Muffler Clean AIR INTAKE/COOLING AreasSparkplugs AIR FilterTo Level Mower Housing CleaningTo Install Mower Tractor To Remove MowerBoth Front Links Should be Equal in Length LiftLink Adjustment NutBottom edge Nut FBelt Removal To Adjust BrakeTo Replace Mower Blade Drive Belt ArmFront Wheel TOE-IN/CAMBER Transaxle Motion Control Lever Neutral AdjustmentTo Adjust Steering Wheel Alignment To Remove Wheel for RepairsTo Replace Headlight Bulb To Start Engine with a Weak BatteryReplacing Battery To Replace FuseTo Adjust Throttle Control Cable To Remove Hood and Grill AssemblyTo Adjust Carburetor To Adjust Choke ControlIdle Mixture Final SettingAcceleration Test Which leads to separation and formation EngineFuel System Engine OILCorrection Troubleshooting ChartCause Problem TroubleshootingChart Cause Troubleshooting Chart Schematic Tractor - Model NumberElectrical KEY Part NO, NO.DESCRIPTION Bolt, Hex 1/4-20 x 3/4Tractor - Model Number Chassis and Enclosures DraVear DescriptionChassis Rod Pivot Chassis/HoodGround Drive Tractor .MODEL Number Tractor - Model Number Ground Drive Tractor - Model Number Steering Assembly Spindle Assembly, R.H FrontAxle AssemblySpindle Assembly, L.H Washer 25/32 x 1-5/8 x 16 GaugeSpark Arrester EngineOptional Equipment 3933162152 121248X Tractor - Model Number Seat Assembly140123 Seat 3450 BIk/blk Craftsman 121246X Washer 13/32 X 1 X 14 GaPart Description Decals KEY Part DescriptionWheels & Tires Tractor - Model Number Lift Assembly 2928 1112 19 j 2O2032 73540600 Nut Crewnlock 3/8-24 155097 Pin Groove30 150233 Trunnion, Inf. Height 50 110452X Nut, Push Phos. &-OilMower Deck KEY Part Description KEY PartNO. no Tractor - Model Number Hydro Gear Transaxle - Model Number Hydro Gear Transaxle Model Number1132 13= 634 552A 404 o220 332 934 859 433 386 j 258 1138 211877 Gasket SET Screw AssemblyHousing Piston869 Intake 425 94823 Screw Air Cleaner307 94930 870 262924 Seat-Valve Exhaust 432 693492 Cap-Spring 871Page Page Sighting Guide Only Ride UP and Down HILL, not Across HillSE/ S

917.270962 specifications

The Craftsman 917.270962 is a well-regarded riding mower that offers a blend of performance, reliability, and user-friendly features. Designed for homeowners with medium to large lawns, this mower provides an efficient mowing experience, making lawn care a less daunting task.

One of the standout features of the Craftsman 917.270962 is its powerful engine. Equipped with a robust 19.5 horsepower Briggs & Stratton engine, it delivers ample power for cutting through thick grass and tackling uneven terrain. This engine not only ensures reliable starting and operation but also enhances fuel efficiency, allowing users to cover larger areas without frequent refueling.

The mower’s cutting deck is another highlight, featuring a 42-inch deck that offers a wide cutting path. This size allows for faster mowing times while maintaining precision. The deck is constructed with a durable steel that can withstand the rigors of regular use, ensuring longevity and resilience. The mower also offers a range of cutting heights that can be easily adjusted, allowing users to customize the mowing process according to the height of their grass.

In terms of maneuverability, the Craftsman 917.270962 is built with a tight turning radius, enabling it to navigate around obstacles and tight spaces with ease. The comfortable, adjustable seat ensures that the user can operate the mower for extended periods without discomfort, making lawn care more enjoyable. It also features responsive steering and foot-controlled hydrostatic transmission, which provides a smooth driving experience without the need for manual gear shifting.

User accessibility is further enhanced by the intuitive controls and dashboard display, which offer easy access to essential functions. Safety features, such as the automatic blade stop when the operator leaves the seat, ensure peace of mind during operation.

Additionally, the Craftsman 917.270962 is compatible with a variety of attachments, including baggers and mulch kits, which enhance versatility and allow users to customize their lawn care approach.

Overall, the Craftsman 917.270962 is a reliable riding mower that combines power, efficiency, and user-friendliness, making it an excellent choice for homeowners looking to maintain their lawns effectively and with minimal effort.
Top Page Image Contents