Craftsman 917.270962 HOW to USE Your Tractor, To SET Parking Brake, To USE Throttle Control

Page 13

The operation of any tractor the eyes, which can result in glasses or eye shields while adjustments or repairs. We over spectacles or standard

can result in foreign objects thrown into severe eye damage. Always wear safety operating your tractor or performing any recommend a wide vision safety mask safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE

Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut oft the engine.

•Depress clutch/brake pedal into full "BRAKE" position and hold.

•Place parking brake lever in "EN-

GAGED" position and release pres- sure from clutch/brake pedal. Pedal should remain in "BRAKE" position.

Make sure parking brake will hold tractor secure. Attachment Clutch Lever

Choke"Engaged" Position

"Disengaged"

Position

Throttl_=g

Brake

"Engaged"

Clutch/

Brake_

Motion

"Disengaged". AdjustmentControl

Position Knob "Brake" Lever

STOPPINGPosition

MOWER BLADES -

•To stop mower blades,move attach- ment clutch lever to "DISENGAGED"

position.

GROUND DRIVE -

•To stop ground drive, depress clutch/ brake pedal into full "BRAKE" position.

•Move motion control lever to neutral

(N) position.

IMPORTANT: The motion control lever

does not return to neutral (N) position when the clutch/brake pedal is de- pressed.

ENGINE -

•Move throttle control to slow position. NOTE: Failure to move throttle control to

slow position and allowing engine to idle before stopping may cause engine to "backfire".

•Turn ignition key to "OFF" position and

remove key. Always remove key when leaving tractor to prevent unauthorized use.

•Never use choke to stop engine.

IMPORTANT: Leaving the ignition switch in any position other than "OFF" will cause the battery to be discharged,

(dead).

NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause "browning" of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

/k CAUTION: Always stop tractor completely, as described above, before

leaving the operator's position; to empty grass catcher, etc.

TO USE THROTTLE CONTROL

Always operate engine at full throttle.

•Operating engine at less than full

throttle reduces the battery charging rate.

•Full throttle otters the best bagging and mower performance.

TO USE CHOKE CONTROL

Use choke control whenever you are starting a cold engine. Do not use to start a warm engine.

•To engage choke control, pull knob out. Slowly push knob in to disen- gage.

TO MOVE FORWARD AND BACK- WARD

The direction and speed of movement is controlled by the motion control lever.

•Start tractor with motion control lever in neutral (N) position,

•Release parking brake and clutch/ brake pedal.

•Slowly move motion control lever to desired position.

TO ADJUST MOWER CUI-rlNG

HEIGHT

The cutting height is controlled by turning the height adjustment knob in desired direction.

•Turn knob clockwise (F_) to raise cutting height,

•Turn knob counterclockwise (k'_,)to lower cutting height.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Am 5 pm, Mon Sat Sears Craftsman Help LineLimited 90 DAY Warranty on Battery Limited TWO Year Warranty on Craftsman Riding EquipmentProduct SEARS, Roebuck and CO., D1817 WA, Hoffman ESTATES, ILSlope Operation ServiceBlades and proceed slowly straight Do notTor Maintenance Agreement Product SpecificationsCustomer Responsibilities AboveLocknut 5/16-18 AdapterTo Remove Tractor from Carton Tools Required for AssemblyBefore Removing Tractor from Skid Attach Steering Wheel Unpack CartonCheck Battery HOW to SET UP Your TractorShoulder Bolt Seat To Drive Tractor OFF SkidCheck Tire Pressure Install Mulcher PlateCheck Deck Levelness ALL BeltsWhile Learning HOW to USE Your ChecklistH L Knowyour Tractor AdjustmentFree Wheel Lift Lever Plunger Used toTo SET Parking Brake HOW to USE Your TractorTo USE Throttle Control To Move Forward and BACK- WardTo Operate Mower To Adjust Gauge WheelsTo Operate on Hills To Start Engine AddgasolineTowing Carts and Other Attachments Before Starting the Enigne Check Engine OIL LevelPurge Transmission Automatic Transmission Warm UP1CAUTION Never engage or disen Position. Shut- off engine and set parking brakeMulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication ChartBefore Each USE Brake Operation BatteryBlade Care Blade RemovalClean AIR Screen Sparkplugs Clean AIR INTAKE/COOLING AreasMuffler AIR FilterTo Install Mower CleaningTo Level Mower Housing Tractor To Remove MowerBottom edge LiftLink Adjustment NutBoth Front Links Should be Equal in Length Nut FTo Replace Mower Blade Drive Belt To Adjust BrakeBelt Removal ArmTo Adjust Steering Wheel Alignment Transaxle Motion Control Lever Neutral AdjustmentFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsReplacing Battery To Start Engine with a Weak BatteryTo Replace Headlight Bulb To Replace FuseTo Adjust Carburetor To Remove Hood and Grill AssemblyTo Adjust Throttle Control Cable To Adjust Choke ControlAcceleration Test Final SettingIdle Mixture Fuel System EngineWhich leads to separation and formation Engine OILCause Troubleshooting ChartCorrection Chart Cause TroubleshootingProblem Troubleshooting Chart Tractor - Model Number SchematicElectrical Bolt, Hex 1/4-20 x 3/4 KEY Part NO, NO.DESCRIPTIONTractor - Model Number Chassis and Enclosures Chassis DescriptionDraVear Rod Pivot Chassis/HoodGround Drive Tractor .MODEL Number Tractor - Model Number Ground Drive Tractor - Model Number Steering Assembly Spindle Assembly, L.H FrontAxle AssemblySpindle Assembly, R.H Washer 25/32 x 1-5/8 x 16 GaugeOptional Equipment EngineSpark Arrester 3933162152 140123 Seat 3450 BIk/blk Craftsman 121246X Tractor - Model Number Seat Assembly121248X Washer 13/32 X 1 X 14 GaWheels & Tires Decals KEY Part DescriptionPart Description 2928 1112 19 j 2O20 Tractor - Model Number Lift Assembly30 150233 Trunnion, Inf. Height Pin Groove32 73540600 Nut Crewnlock 3/8-24 155097 50 110452X Nut, Push Phos. &-OilMower Deck NO. no KEY PartKEY Part Description Tractor - Model Number Hydro Gear Transaxle - Model Number Model Number Hydro Gear Transaxle220 13= 634 552A 404 o1132 877 859 433 386 j 258 1138 211332 934 Gasket SET Housing AssemblyScrew Piston307 94930 Intake 425 94823 Screw Air Cleaner869 870 262924 Seat-Valve Exhaust 432 693492 Cap-Spring 871Page Page Only Ride UP and Down HILL, not Across Hill Sighting GuideSE/ S

917.270962 specifications

The Craftsman 917.270962 is a well-regarded riding mower that offers a blend of performance, reliability, and user-friendly features. Designed for homeowners with medium to large lawns, this mower provides an efficient mowing experience, making lawn care a less daunting task.

One of the standout features of the Craftsman 917.270962 is its powerful engine. Equipped with a robust 19.5 horsepower Briggs & Stratton engine, it delivers ample power for cutting through thick grass and tackling uneven terrain. This engine not only ensures reliable starting and operation but also enhances fuel efficiency, allowing users to cover larger areas without frequent refueling.

The mower’s cutting deck is another highlight, featuring a 42-inch deck that offers a wide cutting path. This size allows for faster mowing times while maintaining precision. The deck is constructed with a durable steel that can withstand the rigors of regular use, ensuring longevity and resilience. The mower also offers a range of cutting heights that can be easily adjusted, allowing users to customize the mowing process according to the height of their grass.

In terms of maneuverability, the Craftsman 917.270962 is built with a tight turning radius, enabling it to navigate around obstacles and tight spaces with ease. The comfortable, adjustable seat ensures that the user can operate the mower for extended periods without discomfort, making lawn care more enjoyable. It also features responsive steering and foot-controlled hydrostatic transmission, which provides a smooth driving experience without the need for manual gear shifting.

User accessibility is further enhanced by the intuitive controls and dashboard display, which offer easy access to essential functions. Safety features, such as the automatic blade stop when the operator leaves the seat, ensure peace of mind during operation.

Additionally, the Craftsman 917.270962 is compatible with a variety of attachments, including baggers and mulch kits, which enhance versatility and allow users to customize their lawn care approach.

Overall, the Craftsman 917.270962 is a reliable riding mower that combines power, efficiency, and user-friendliness, making it an excellent choice for homeowners looking to maintain their lawns effectively and with minimal effort.
Top Page Image Contents