Craftsman 917.270962 owner manual Bottom edge, Both Front Links Should be Equal in Length, Nut F

Page 23

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD-

UCT SPECIFICATIONS" section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of

mower to ground. Distance "A" on both sides of mower should be the

same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift

link adjustment nut on that side. NOTE:Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjust- ing.

Bottom edge of

Bottom edge of

•Before making any necessary adjust- ments, check that both front links are equal in length. Both links should be

approximately 10-3/8".

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut "E"

on both front links an equal number of turns.

°When distance "D" is 1/8" to 1/2" lower at front than rear, tighten nuts "F" against trunnion on both front links.

°To raise front of mower, loosen nut "F" from trunnion on both front links.

Tighten nut "E" on both front links an

equal number of turns.

•When distance "D" is 1/8" to 1/2" lower at front than rear, tighten nut "F" against trunnion on both front links.

•Recheck side-to-side adjustment.

Mandrel

m°w_Wer_grOund

Both Front Links Should be Equal in Length

Suspension

LiftLink Adjustment Nut

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to side. if the following front-to-back adjustment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in

its highest position.

Check adjustment on right side of tractor. Measure distance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

"E"

Nut "F"_

Nut

Trunnion"_>

Front Links

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Am 5 pm, Mon Sat Sears Craftsman Help LineSEARS, Roebuck and CO., D1817 WA, Hoffman ESTATES, IL Limited TWO Year Warranty on Craftsman Riding EquipmentLimited 90 DAY Warranty on Battery ProductDo not ServiceSlope Operation Blades and proceed slowly straightTor Above Product SpecificationsMaintenance Agreement Customer ResponsibilitiesLocknut 5/16-18 AdapterUnpack Carton Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from Skid Attach Steering WheelTo Drive Tractor OFF Skid HOW to SET UP Your TractorCheck Battery Shoulder Bolt SeatALL Belts Install Mulcher PlateCheck Tire Pressure Check Deck LevelnessWhile Learning HOW to USE Your ChecklistH L Lift Lever Plunger Used to AdjustmentKnowyour Tractor Free WheelTo Move Forward and BACK- Ward HOW to USE Your TractorTo SET Parking Brake To USE Throttle ControlTo Operate on Hills To Adjust Gauge WheelsTo Operate Mower Before Starting the Enigne Check Engine OIL Level AddgasolineTo Start Engine Towing Carts and Other AttachmentsPosition. Shut- off engine and set parking brake Automatic Transmission Warm UPPurge Transmission 1CAUTION Never engage or disenMulching Mowing Tips Mowing TipsBefore Each USE Lubrication ChartGeneral Recommendations Blade Removal BatteryBrake Operation Blade CareClean AIR Screen AIR Filter Clean AIR INTAKE/COOLING AreasSparkplugs MufflerTractor To Remove Mower CleaningTo Install Mower To Level Mower HousingNut F LiftLink Adjustment NutBottom edge Both Front Links Should be Equal in LengthArm To Adjust BrakeTo Replace Mower Blade Drive Belt Belt RemovalTo Remove Wheel for Repairs Transaxle Motion Control Lever Neutral AdjustmentTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Replace Fuse To Start Engine with a Weak BatteryReplacing Battery To Replace Headlight BulbTo Adjust Choke Control To Remove Hood and Grill AssemblyTo Adjust Carburetor To Adjust Throttle Control CableIdle Mixture Final SettingAcceleration Test Engine OIL EngineFuel System Which leads to separation and formationCorrection Troubleshooting ChartCause Problem TroubleshootingChart Cause Troubleshooting Chart Tractor - Model Number SchematicElectrical Bolt, Hex 1/4-20 x 3/4 KEY Part NO, NO.DESCRIPTIONTractor - Model Number Chassis and Enclosures Rod Pivot Chassis/Hood DescriptionChassis DraVearGround Drive Tractor .MODEL Number Tractor - Model Number Ground Drive Tractor - Model Number Steering Assembly Washer 25/32 x 1-5/8 x 16 Gauge FrontAxle AssemblySpindle Assembly, L.H Spindle Assembly, R.H3933 EngineOptional Equipment Spark Arrester162152 Washer 13/32 X 1 X 14 Ga Tractor - Model Number Seat Assembly140123 Seat 3450 BIk/blk Craftsman 121246X 121248XPart Description Decals KEY Part DescriptionWheels & Tires 2928 1112 19 j 2O20 Tractor - Model Number Lift Assembly50 110452X Nut, Push Phos. &-Oil Pin Groove30 150233 Trunnion, Inf. Height 32 73540600 Nut Crewnlock 3/8-24 155097Mower Deck KEY Part Description KEY PartNO. no Tractor - Model Number Hydro Gear Transaxle - Model Number Model Number Hydro Gear Transaxle1132 13= 634 552A 404 o220 332 934 859 433 386 j 258 1138 211877 Gasket SET Piston AssemblyHousing Screw870 262924 Seat-Valve Exhaust 432 693492 Cap-Spring 871 Intake 425 94823 Screw Air Cleaner307 94930 869Page Page Only Ride UP and Down HILL, not Across Hill Sighting GuideSE/ S

917.270962 specifications

The Craftsman 917.270962 is a well-regarded riding mower that offers a blend of performance, reliability, and user-friendly features. Designed for homeowners with medium to large lawns, this mower provides an efficient mowing experience, making lawn care a less daunting task.

One of the standout features of the Craftsman 917.270962 is its powerful engine. Equipped with a robust 19.5 horsepower Briggs & Stratton engine, it delivers ample power for cutting through thick grass and tackling uneven terrain. This engine not only ensures reliable starting and operation but also enhances fuel efficiency, allowing users to cover larger areas without frequent refueling.

The mower’s cutting deck is another highlight, featuring a 42-inch deck that offers a wide cutting path. This size allows for faster mowing times while maintaining precision. The deck is constructed with a durable steel that can withstand the rigors of regular use, ensuring longevity and resilience. The mower also offers a range of cutting heights that can be easily adjusted, allowing users to customize the mowing process according to the height of their grass.

In terms of maneuverability, the Craftsman 917.270962 is built with a tight turning radius, enabling it to navigate around obstacles and tight spaces with ease. The comfortable, adjustable seat ensures that the user can operate the mower for extended periods without discomfort, making lawn care more enjoyable. It also features responsive steering and foot-controlled hydrostatic transmission, which provides a smooth driving experience without the need for manual gear shifting.

User accessibility is further enhanced by the intuitive controls and dashboard display, which offer easy access to essential functions. Safety features, such as the automatic blade stop when the operator leaves the seat, ensure peace of mind during operation.

Additionally, the Craftsman 917.270962 is compatible with a variety of attachments, including baggers and mulch kits, which enhance versatility and allow users to customize their lawn care approach.

Overall, the Craftsman 917.270962 is a reliable riding mower that combines power, efficiency, and user-friendliness, making it an excellent choice for homeowners looking to maintain their lawns effectively and with minimal effort.
Top Page Image Contents