Craftsman 917.270962 Battery, Brake Operation, Blade Care, Blade Removal, To Sharpen Blade

Page 19

TRACTOR

Always observe safety rules when

performing any maintenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be

adjusted. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual).

TIRES

Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual).

Keep tires free of gasoline, oil, or insect control chemicals which can

harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may

cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also

prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are working properly. If your tractor does not function as described, repair the problem immediately.

The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in

the disengaged position.

When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

The attachment clutch should never

operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be

kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

Raise mower to highest position to allow access to blades.

Remove hex bolt, lock washer and flat washer securing blade.

Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: To ensure proper assem-

bly, center hole in blade must align with star on mandrel assembly.

Reassemble hex bolt, lock washer and flat washer in exact order as shown.

• Tighten bolt securely (27-35 Ft. Lbs.

torque).

IMPORTANT: Blade bolt is Grade 8 heat

treated.

 

Trailing Edge Up

Mandrel Assembly

Blade

Center

 

Hole

Flat Washer.

 

Lock Washer

 

_--_-Hex Bolt (Grade)

*A Grade 8 heat treated bolt can be identified by six lines on the bolt head.

TO SHARPEN BLADE

NOTE: We do not recommend sharpen-

ing blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will

cause excessive vibration and eventual damage to mower and engine.

The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a

cone balancer. (When using a cone balancer, follow the instructions

supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Slide blade on to an unthreaded

portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen

the heavy end until the blade is balanced.

5/8" B_d

e

Center Hole

BATTERY

Your tractor has a battery charging system which is sufficient for normal use.

However, periodic charging of the battery with an automotive charger will extend its life.

Keep battery bolts tight.

Keep smallbattery ventand holesterminalsopen.clean.

19 Recharge at 6-10 amperes for 1 hour.

Image 19
Contents Am 5 pm, Mon Sat Sears Craftsman Help LineSEARS, Roebuck and CO., D1817 WA, Hoffman ESTATES, IL Limited TWO Year Warranty on Craftsman Riding EquipmentLimited 90 DAY Warranty on Battery ProductDo not ServiceSlope Operation Blades and proceed slowly straightTor Above Product SpecificationsMaintenance Agreement Customer ResponsibilitiesLocknut 5/16-18 AdapterUnpack Carton Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from Skid Attach Steering WheelTo Drive Tractor OFF Skid HOW to SET UP Your TractorCheck Battery Shoulder Bolt SeatALL Belts Install Mulcher PlateCheck Tire Pressure Check Deck LevelnessWhile Learning HOW to USE Your ChecklistH L Lift Lever Plunger Used to AdjustmentKnowyour Tractor Free WheelTo Move Forward and BACK- Ward HOW to USE Your TractorTo SET Parking Brake To USE Throttle ControlTo Operate Mower To Adjust Gauge WheelsTo Operate on Hills Before Starting the Enigne Check Engine OIL Level AddgasolineTo Start Engine Towing Carts and Other AttachmentsPosition. Shut- off engine and set parking brake Automatic Transmission Warm UPPurge Transmission 1CAUTION Never engage or disenMulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication ChartBefore Each USE Blade Removal BatteryBrake Operation Blade CareClean AIR Screen AIR Filter Clean AIR INTAKE/COOLING AreasSparkplugs MufflerTractor To Remove Mower CleaningTo Install Mower To Level Mower HousingNut F LiftLink Adjustment NutBottom edge Both Front Links Should be Equal in LengthArm To Adjust BrakeTo Replace Mower Blade Drive Belt Belt RemovalTo Remove Wheel for Repairs Transaxle Motion Control Lever Neutral AdjustmentTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Replace Fuse To Start Engine with a Weak BatteryReplacing Battery To Replace Headlight BulbTo Adjust Choke Control To Remove Hood and Grill AssemblyTo Adjust Carburetor To Adjust Throttle Control CableAcceleration Test Final SettingIdle Mixture Engine OIL EngineFuel System Which leads to separation and formationCause Troubleshooting ChartCorrection Chart Cause TroubleshootingProblem Troubleshooting Chart Tractor - Model Number SchematicElectrical Bolt, Hex 1/4-20 x 3/4 KEY Part NO, NO.DESCRIPTIONTractor - Model Number Chassis and Enclosures Rod Pivot Chassis/Hood DescriptionChassis DraVearGround Drive Tractor .MODEL Number Tractor - Model Number Ground Drive Tractor - Model Number Steering Assembly Washer 25/32 x 1-5/8 x 16 Gauge FrontAxle AssemblySpindle Assembly, L.H Spindle Assembly, R.H3933 EngineOptional Equipment Spark Arrester162152 Washer 13/32 X 1 X 14 Ga Tractor - Model Number Seat Assembly140123 Seat 3450 BIk/blk Craftsman 121246X 121248XWheels & Tires Decals KEY Part DescriptionPart Description 2928 1112 19 j 2O20 Tractor - Model Number Lift Assembly50 110452X Nut, Push Phos. &-Oil Pin Groove30 150233 Trunnion, Inf. Height 32 73540600 Nut Crewnlock 3/8-24 155097Mower Deck NO. no KEY PartKEY Part Description Tractor - Model Number Hydro Gear Transaxle - Model Number Model Number Hydro Gear Transaxle220 13= 634 552A 404 o1132 877 859 433 386 j 258 1138 211332 934 Gasket SET Piston AssemblyHousing Screw870 262924 Seat-Valve Exhaust 432 693492 Cap-Spring 871 Intake 425 94823 Screw Air Cleaner307 94930 869Page Page Only Ride UP and Down HILL, not Across Hill Sighting GuideSE/ S

917.270962 specifications

The Craftsman 917.270962 is a well-regarded riding mower that offers a blend of performance, reliability, and user-friendly features. Designed for homeowners with medium to large lawns, this mower provides an efficient mowing experience, making lawn care a less daunting task.

One of the standout features of the Craftsman 917.270962 is its powerful engine. Equipped with a robust 19.5 horsepower Briggs & Stratton engine, it delivers ample power for cutting through thick grass and tackling uneven terrain. This engine not only ensures reliable starting and operation but also enhances fuel efficiency, allowing users to cover larger areas without frequent refueling.

The mower’s cutting deck is another highlight, featuring a 42-inch deck that offers a wide cutting path. This size allows for faster mowing times while maintaining precision. The deck is constructed with a durable steel that can withstand the rigors of regular use, ensuring longevity and resilience. The mower also offers a range of cutting heights that can be easily adjusted, allowing users to customize the mowing process according to the height of their grass.

In terms of maneuverability, the Craftsman 917.270962 is built with a tight turning radius, enabling it to navigate around obstacles and tight spaces with ease. The comfortable, adjustable seat ensures that the user can operate the mower for extended periods without discomfort, making lawn care more enjoyable. It also features responsive steering and foot-controlled hydrostatic transmission, which provides a smooth driving experience without the need for manual gear shifting.

User accessibility is further enhanced by the intuitive controls and dashboard display, which offer easy access to essential functions. Safety features, such as the automatic blade stop when the operator leaves the seat, ensure peace of mind during operation.

Additionally, the Craftsman 917.270962 is compatible with a variety of attachments, including baggers and mulch kits, which enhance versatility and allow users to customize their lawn care approach.

Overall, the Craftsman 917.270962 is a reliable riding mower that combines power, efficiency, and user-friendliness, making it an excellent choice for homeowners looking to maintain their lawns effectively and with minimal effort.