Craftsman 917.270962 Fuel System, Which leads to separation and formation, Engine OIL

Page 29

Immediately prepare your tractor for

storage at the end of the season or if the tractor will not be used for 30 days or more.

w_lt CAUTION: Never store the tractor h gasoline in the tank inside a building where fumes may reach an

open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

Clean entire tractor (See "CLEANING"

in the Maintenance section of this manual).

Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual).

Lubricate as shown in the Mainte- nance section ot this manual.

Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BA'FrERY

Fully charge the battery for storage.

After a period of time in storage, battery may require recharging.

To help prevent corrosion and power leakage during long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see "TO CLEAN BATTERY AND TERMINALS" in the Maintenance section of this manual).

After cleaning, leave cables discon- nected and place cables where they cannot come in contact with battery terminals.

If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: It is important to prevent puUm deposits from forming in essential

el system parts such as carburetor, fuel filter, fuel hose, or tank during storage. Also, experience indicates that alcohot blended fuels called gasohol or using

ethanol or methanol) can attract moisture

which leads to separation and formation

of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

Drain the fuel tank.

Start the engine and let it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or

storage container. Always follow the mix ratio found on stabilizer container. Run

engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach

the carburetor. Do not drain the gas tank

and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See "ENGINE" in

the Maintenance section of this manual).

CYLINDER(S)

Remove spark plug(s).

Pour one ounce of oil through spark plug hole(s) into cylinder(s).

Turn ignition key to "START" position for a few seconds to distribute oil.

Replace with new spark plug(s).

OTHER

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

If possible, store your tractor indoors

and cover it to give protection from dust and dirt.

Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows conden-

sation to form and will cause your tractor to rust.

IMPORTANT: Never cover tractor while

engine and exhaust areas are still warm.

29

Image 29
Contents Am 5 pm, Mon Sat Sears Craftsman Help LineLimited 90 DAY Warranty on Battery Limited TWO Year Warranty on Craftsman Riding EquipmentProduct SEARS, Roebuck and CO., D1817 WA, Hoffman ESTATES, ILSlope Operation ServiceBlades and proceed slowly straight Do notTor Maintenance Agreement Product SpecificationsCustomer Responsibilities AboveLocknut 5/16-18 AdapterTo Remove Tractor from Carton Tools Required for AssemblyBefore Removing Tractor from Skid Attach Steering Wheel Unpack CartonCheck Battery HOW to SET UP Your TractorShoulder Bolt Seat To Drive Tractor OFF SkidCheck Tire Pressure Install Mulcher PlateCheck Deck Levelness ALL BeltsWhile Learning HOW to USE Your ChecklistH L Knowyour Tractor AdjustmentFree Wheel Lift Lever Plunger Used toTo SET Parking Brake HOW to USE Your TractorTo USE Throttle Control To Move Forward and BACK- WardTo Operate on Hills To Adjust Gauge WheelsTo Operate Mower To Start Engine AddgasolineTowing Carts and Other Attachments Before Starting the Enigne Check Engine OIL LevelPurge Transmission Automatic Transmission Warm UP1CAUTION Never engage or disen Position. Shut- off engine and set parking brakeMulching Mowing Tips Mowing TipsBefore Each USE Lubrication ChartGeneral Recommendations Brake Operation BatteryBlade Care Blade RemovalClean AIR Screen Sparkplugs Clean AIR INTAKE/COOLING AreasMuffler AIR FilterTo Install Mower CleaningTo Level Mower Housing Tractor To Remove MowerBottom edge LiftLink Adjustment NutBoth Front Links Should be Equal in Length Nut FTo Replace Mower Blade Drive Belt To Adjust BrakeBelt Removal ArmTo Adjust Steering Wheel Alignment Transaxle Motion Control Lever Neutral AdjustmentFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsReplacing Battery To Start Engine with a Weak BatteryTo Replace Headlight Bulb To Replace FuseTo Adjust Carburetor To Remove Hood and Grill AssemblyTo Adjust Throttle Control Cable To Adjust Choke ControlIdle Mixture Final SettingAcceleration Test Fuel System EngineWhich leads to separation and formation Engine OILCorrection Troubleshooting ChartCause Problem TroubleshootingChart Cause Troubleshooting Chart Tractor - Model Number SchematicElectrical Bolt, Hex 1/4-20 x 3/4 KEY Part NO, NO.DESCRIPTIONTractor - Model Number Chassis and Enclosures Chassis DescriptionDraVear Rod Pivot Chassis/HoodGround Drive Tractor .MODEL Number Tractor - Model Number Ground Drive Tractor - Model Number Steering Assembly Spindle Assembly, L.H FrontAxle AssemblySpindle Assembly, R.H Washer 25/32 x 1-5/8 x 16 GaugeOptional Equipment EngineSpark Arrester 3933162152 140123 Seat 3450 BIk/blk Craftsman 121246X Tractor - Model Number Seat Assembly121248X Washer 13/32 X 1 X 14 GaPart Description Decals KEY Part DescriptionWheels & Tires 2928 1112 19 j 2O20 Tractor - Model Number Lift Assembly30 150233 Trunnion, Inf. Height Pin Groove32 73540600 Nut Crewnlock 3/8-24 155097 50 110452X Nut, Push Phos. &-OilMower Deck KEY Part Description KEY PartNO. no Tractor - Model Number Hydro Gear Transaxle - Model Number Model Number Hydro Gear Transaxle1132 13= 634 552A 404 o220 332 934 859 433 386 j 258 1138 211877 Gasket SET Housing AssemblyScrew Piston307 94930 Intake 425 94823 Screw Air Cleaner869 870 262924 Seat-Valve Exhaust 432 693492 Cap-Spring 871Page Page Only Ride UP and Down HILL, not Across Hill Sighting GuideSE/ S

917.270962 specifications

The Craftsman 917.270962 is a well-regarded riding mower that offers a blend of performance, reliability, and user-friendly features. Designed for homeowners with medium to large lawns, this mower provides an efficient mowing experience, making lawn care a less daunting task.

One of the standout features of the Craftsman 917.270962 is its powerful engine. Equipped with a robust 19.5 horsepower Briggs & Stratton engine, it delivers ample power for cutting through thick grass and tackling uneven terrain. This engine not only ensures reliable starting and operation but also enhances fuel efficiency, allowing users to cover larger areas without frequent refueling.

The mower’s cutting deck is another highlight, featuring a 42-inch deck that offers a wide cutting path. This size allows for faster mowing times while maintaining precision. The deck is constructed with a durable steel that can withstand the rigors of regular use, ensuring longevity and resilience. The mower also offers a range of cutting heights that can be easily adjusted, allowing users to customize the mowing process according to the height of their grass.

In terms of maneuverability, the Craftsman 917.270962 is built with a tight turning radius, enabling it to navigate around obstacles and tight spaces with ease. The comfortable, adjustable seat ensures that the user can operate the mower for extended periods without discomfort, making lawn care more enjoyable. It also features responsive steering and foot-controlled hydrostatic transmission, which provides a smooth driving experience without the need for manual gear shifting.

User accessibility is further enhanced by the intuitive controls and dashboard display, which offer easy access to essential functions. Safety features, such as the automatic blade stop when the operator leaves the seat, ensure peace of mind during operation.

Additionally, the Craftsman 917.270962 is compatible with a variety of attachments, including baggers and mulch kits, which enhance versatility and allow users to customize their lawn care approach.

Overall, the Craftsman 917.270962 is a reliable riding mower that combines power, efficiency, and user-friendliness, making it an excellent choice for homeowners looking to maintain their lawns effectively and with minimal effort.