Craftsman 917.270962 To Remove Tractor from Carton, Tools Required for Assembly, Unpack Carton

Page 7

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly

easier. Standard wrench sizes you need are listed below.

(1)

9/16"

wrench

(1)

Pliers

(2)

1/2" wrench

(1)

Utility

knife

(1)

3/4"

socket with

(1)

Tire

pressure

 

drive

ratchet

 

gauge

When right or left hand is mentioned in this manual, it means, from your point of view, when you are in the operating position (seated behind the steering wheel).

•Assemble large flat washer, 3/8 lock washer, 3/8 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from

tractor hood and grill.

IMPORTANT: Check for and remove any staples in skid that may puncture tires where tractor is to roll off skid.

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts boxes from shipping canon.

•Cut, from top to bottom, along lines on all four corners of shipping carton, and lay panels flat.

•Check for any additional loose parts or boxes and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower

steering shaft. Align mounting holes in extension and lower shafts and

install 5/16 hex bolt and Iocknut. Tighten securely.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Am 5 pm, Mon Sat Sears Craftsman Help LineSEARS, Roebuck and CO., D1817 WA, Hoffman ESTATES, IL Limited TWO Year Warranty on Craftsman Riding EquipmentLimited 90 DAY Warranty on Battery ProductDo not ServiceSlope Operation Blades and proceed slowly straightTor Above Product SpecificationsMaintenance Agreement Customer ResponsibilitiesLocknut 5/16-18 AdapterUnpack Carton Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from Skid Attach Steering WheelTo Drive Tractor OFF Skid HOW to SET UP Your TractorCheck Battery Shoulder Bolt SeatALL Belts Install Mulcher PlateCheck Tire Pressure Check Deck LevelnessWhile Learning HOW to USE Your ChecklistH L Lift Lever Plunger Used to AdjustmentKnowyour Tractor Free WheelTo Move Forward and BACK- Ward HOW to USE Your TractorTo SET Parking Brake To USE Throttle ControlTo Operate Mower To Adjust Gauge WheelsTo Operate on Hills Before Starting the Enigne Check Engine OIL Level AddgasolineTo Start Engine Towing Carts and Other AttachmentsPosition. Shut- off engine and set parking brake Automatic Transmission Warm UPPurge Transmission 1CAUTION Never engage or disenMulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication ChartBefore Each USE Blade Removal BatteryBrake Operation Blade CareClean AIR Screen AIR Filter Clean AIR INTAKE/COOLING AreasSparkplugs MufflerTractor To Remove Mower CleaningTo Install Mower To Level Mower HousingNut F LiftLink Adjustment NutBottom edge Both Front Links Should be Equal in LengthArm To Adjust BrakeTo Replace Mower Blade Drive Belt Belt RemovalTo Remove Wheel for Repairs Transaxle Motion Control Lever Neutral AdjustmentTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Replace Fuse To Start Engine with a Weak BatteryReplacing Battery To Replace Headlight BulbTo Adjust Choke Control To Remove Hood and Grill AssemblyTo Adjust Carburetor To Adjust Throttle Control CableAcceleration Test Final SettingIdle Mixture Engine OIL EngineFuel System Which leads to separation and formationCause Troubleshooting ChartCorrection Chart Cause TroubleshootingProblem Troubleshooting Chart Tractor - Model Number SchematicElectrical Bolt, Hex 1/4-20 x 3/4 KEY Part NO, NO.DESCRIPTIONTractor - Model Number Chassis and Enclosures Rod Pivot Chassis/Hood DescriptionChassis DraVearGround Drive Tractor .MODEL Number Tractor - Model Number Ground Drive Tractor - Model Number Steering Assembly Washer 25/32 x 1-5/8 x 16 Gauge FrontAxle AssemblySpindle Assembly, L.H Spindle Assembly, R.H3933 EngineOptional Equipment Spark Arrester162152 Washer 13/32 X 1 X 14 Ga Tractor - Model Number Seat Assembly140123 Seat 3450 BIk/blk Craftsman 121246X 121248XWheels & Tires Decals KEY Part DescriptionPart Description 2928 1112 19 j 2O20 Tractor - Model Number Lift Assembly50 110452X Nut, Push Phos. &-Oil Pin Groove30 150233 Trunnion, Inf. Height 32 73540600 Nut Crewnlock 3/8-24 155097Mower Deck NO. no KEY PartKEY Part Description Tractor - Model Number Hydro Gear Transaxle - Model Number Model Number Hydro Gear Transaxle220 13= 634 552A 404 o1132 877 859 433 386 j 258 1138 211332 934 Gasket SET Piston AssemblyHousing Screw870 262924 Seat-Valve Exhaust 432 693492 Cap-Spring 871 Intake 425 94823 Screw Air Cleaner307 94930 869Page Page Only Ride UP and Down HILL, not Across Hill Sighting GuideSE/ S

917.270962 specifications

The Craftsman 917.270962 is a well-regarded riding mower that offers a blend of performance, reliability, and user-friendly features. Designed for homeowners with medium to large lawns, this mower provides an efficient mowing experience, making lawn care a less daunting task.

One of the standout features of the Craftsman 917.270962 is its powerful engine. Equipped with a robust 19.5 horsepower Briggs & Stratton engine, it delivers ample power for cutting through thick grass and tackling uneven terrain. This engine not only ensures reliable starting and operation but also enhances fuel efficiency, allowing users to cover larger areas without frequent refueling.

The mower’s cutting deck is another highlight, featuring a 42-inch deck that offers a wide cutting path. This size allows for faster mowing times while maintaining precision. The deck is constructed with a durable steel that can withstand the rigors of regular use, ensuring longevity and resilience. The mower also offers a range of cutting heights that can be easily adjusted, allowing users to customize the mowing process according to the height of their grass.

In terms of maneuverability, the Craftsman 917.270962 is built with a tight turning radius, enabling it to navigate around obstacles and tight spaces with ease. The comfortable, adjustable seat ensures that the user can operate the mower for extended periods without discomfort, making lawn care more enjoyable. It also features responsive steering and foot-controlled hydrostatic transmission, which provides a smooth driving experience without the need for manual gear shifting.

User accessibility is further enhanced by the intuitive controls and dashboard display, which offer easy access to essential functions. Safety features, such as the automatic blade stop when the operator leaves the seat, ensure peace of mind during operation.

Additionally, the Craftsman 917.270962 is compatible with a variety of attachments, including baggers and mulch kits, which enhance versatility and allow users to customize their lawn care approach.

Overall, the Craftsman 917.270962 is a reliable riding mower that combines power, efficiency, and user-friendliness, making it an excellent choice for homeowners looking to maintain their lawns effectively and with minimal effort.
Top Page Image Contents