Craftsman 358.351080 Customer Responsibilities, Crrftsmrn, Sharpening CHAIFure20, Chain Gauge

Page 18

CUSTOMER RESPONSIBILITIES

: ,.r£:.._i

•If chain is too loose, refer to =Chain Adjustment." Loosen bar clamp nuts; then, turn adjusting screw 1/4 turn clock- wise. Lift up tip of guide bar to check for sag. Retighten bar clamp nuts. Figure 20.

Guide Bar

CRRFTSMRN'

Tool

SHARPENING CHAIF_ure20

(Fig. 21, 22, 23, 24, 25, 26 & 27)

WARNING:

IMPROPER CHAIN SHARPENING TECH- NIQUES ANDIOR ,DEPTH GAUGE MAINTE-

KICKBACK, WHICH CAN RESULT IN SERI- OUS INJURY.

ALWAYS WEAR GLOVES WHEN HANDLING

THE CHAIN. THE CHAIN CAN BE SHARP NANCE WILL INCREASE THE CHANCE OF ENOUGH TO CUT YOU EVEN THOUGH IT IS

TOO DULLTO CUTWOOD.

CHAIN TERMINOLOGY & PART NAMES

Preset Tie Strap

Left Hand Cutter

.

Link

Toolsrequired:

•Rat fife

•.025 depth gauge

•4.5mm round file & file holder

Conditionswhich indicatethe need for chain sharpening:

•Reduction in size of wood chips.The size of the wood

chip wil! decrease as the chain gets duller until it becomes more like a powder than a chip.Note that dead or rottedwood wiltnot producea good chip.

•Saw cuts to one side or at an angle.

-Saw requires excessiveforce to cut.

• Noticeable tossof cuttingspeed.

Sharpeninginstructions:

•Move on/stop switchto the "Stop"position.

•Check chain for proper tension. Adjust chain tension if necessary. (See Chain Tension/Adjustment).

•Check and lowerdepthgaugesbeforesharpeningcutters.

•Depth gauges shouldbe checked every third sharpen. ing.When cuttingfrozen wood the depth gauges should be checked each time you sharpen the chain.

•To check depth gauge, place gauge tool on cutter. If the

depth gauge projects above the tool, then file it level to the top of the depth gauge tool.See Figure 21.

DepthFile

Gauge

Figure 21

 

.030"

Squared

. Rounded

Off Comer

Right Hand Cutter "_._ _

Guard Tie Strap_

!CHAIN CUTTER PART NAMES

Top Plate .......__Gullet

_1_ =/ / Depth Gauge Side Plate --_--1_ .{_p;_l_

Toe _

!vet Hole

CHAIN "PITCH"

CHAIN "GAUGE"

Pitch refers to chain mea- Gauge refers to thickness surement. A chain'spitch is of that portion of drive link the distance between any which fits into saw bar

three of its rivets divided by groove. two.

Right Way "

Wrong Way

Figure 22

•To sharpen the cutters,position the file holder level (90 °) so that it rests on the top edges of the cutter and depth

gauge. See Figure 23.

NOTE: The chain has both left and right hand cutters.

•Sharpen cutters on one side of the chain first. File from the inside of each cutter to the outside.Then turn your saw around and repeat the process for the other side of the chain. See Figure 24.

•File on the fon_vardstroke only.Use 2 or 3 strokes per cutting edge.

•Keep the 30 ° line on the file holder parallel to the center of the chain. Reverse procedure for other side. See

Figure 25.

•Keep all cutters the same length when filing. See Figure 26.

•Fite enough to remove any damage to cutting edges

(side plate and top plate) of cutter.See Figure 26.

°File chain to meet the specifications shown below. See

Figure 27.

18-

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Lk Warning 358.351080-18 358.351160-16Hours CST Result in Serious InjuryPlan Ahead NightKnow Your SAW Fuel HandlingTransporting and Storage KickbackReduce the Chance of Kickback Safety RulesKickback Safety Features Understanding Reactwe ForcesFull ONE Year Warranty on Craftsman GAS Chain SAW Customer ResponsibilitiesSPECIAL Notice Table of Contents IndexCarton Contents Operation Chain TravelDirection Howto USE Your Chain SAW Chain Oiler FigTHROnLE Control Group Fig 401 2-CYCLE AIR-COOLED Engine OIL Guide BAR and Chain OIL Fuel Mixture ChartBefore Starting Engine GasolineFull Starting a Warm EngineDifficult sTARTlinG or Flooded Engine Right Foot through Opening in Rear HandleTo Avoid PINCH-KICKBACK Avoid Reactive Pinch ForcesGeneral Operation Tips To Avoid PULL-INFelling Tips Tree FellingDetermine the Natural Fall Direction OHAMMER to Force the Felling CUT PEN. the Wedge will HoldOperation Safety Felling SafetyTypes of Cutting Fig Bucking SafetyBucking Bucking on the Ground FigPruning and Limbing Tips Pruning and LimbingPruning Fig Never Cumb Into a Tree Tolimb orCheck for Damaged or Worn Parts Maintenance ScheduleBefore USE Check for Loose Fasteners and PartsSharpening CHAIFure20 Customer ResponsibilitiesCrrftsmrn Chain GaugeHolder File HolderInside Side PlateEvery 25 Hours Clean Unit and LabelsAfter USE YearlyFuel Line Barrel Service and Adjustments Chnn Adjustment , 41,42 & do43notBar Clamp Nuts NutsScrew Tool Starter Rope Replacement , 45, 46, 47Housing Starter Rope Fan Housin PulleyRewind for Idle Speed Adjustment Mixture Carburetor AdjustmentsIdle Speed Adjustment is marked with the letter T LOW Speed Mixture ADJUflTMEAfter completing adjustments, check for acceleration Adjusting Procedure Idle Speed Adjustment TLOW Speed Mixture Adjustment L Acceleration CheckFuel System StorageGAS Chain SAW Storage Instructions Internal EngineTrouble Shooting Points Trouble Shooting Chart Symptom Cause CorrectionAssy Repair PartsBarAdjungKit LargeDaGrner S30-037733 Foam-Nr FilterClp UmirCo-.owRepair Parts Customer Assistance Ifyou Need Repair Service or PartsRepair Service 1-800-4-REPAIR 358.351080 358.351160 358.351180

358.351080 specifications

The Craftsman 358.351080 is a versatile and reliable gas-powered string trimmer designed for both residential and light commercial use. This trimmer is particularly beloved for its robust performance and user-friendly features, making it an essential tool for maintaining a well-kept lawn or garden.

One of the standout characteristics of the Craftsman 358.351080 is its powerful 32cc, 2-cycle engine. This engine provides ample power to tackle tough weeds, thick grass, and even small brush. Despite its strength, the engine is designed to be fuel-efficient, which translates to longer operating times and fewer fuel refills. The use of a 2-cycle engine means that users will need to mix oil with the gasoline, but this also provides a lightweight and compact design that makes handling easier.

A key feature of the Craftsman 358.351080 is its easy-to-use starting system. This trimmer incorporates an ergonomically designed starting mechanism that aids in quick and effortless ignition, reducing the frustration often associated with starting gas-powered tools. The inclusion of an automatic choke system further enhances this ease of use, ensuring that the engine runs smoothly from the first pull.

The Craftsman 358.351080 also boasts a generous cutting swath of 17 inches. This large cutting diameter allows for efficient trimming, significantly reducing the time it takes to complete lawn maintenance tasks. Additionally, the trimmer is equipped with a dual line bump head which allows for easy line advancement; users can simply tap the head on the ground to release more cutting line when needed.

Comfort is another important aspect of the Craftsman 358.351080. The trimmer features a comfortable, adjustable handle that can be tailored to suit the user’s height and grip preferences. This not only ensures better control while trimming but also helps reduce fatigue during prolonged use. Furthermore, the lightweight design of the trimmer allows for easy maneuverability, making it suitable for various garden types and terrains.

Safety features are also integrated into the design of the Craftsman 358.351080, with protective equipment and safety switches to prevent accidental starts. This commitment to user safety makes it an excellent choice for inexperienced users or those looking to operate the trimmer for extended periods.

In summary, the Craftsman 358.351080 string trimmer is a powerful, efficient, and user-friendly tool. With its impressive engine performance, generous cutting swath, and focus on user comfort and safety, it is well-suited for a variety of landscaping tasks. Whether you are a homeowner or a light commercial operator, this trimmer delivers the reliability and effectiveness needed to keep your outdoor spaces pristine.
Top Page Image Contents