HOW to USE Your Riding Mower, Stopping | Weed Eater WE261 instruction

RETIRO DE LA CUCHILLA

1.Eleve la cortadora de césped a la posición más alta para tener acceso a la cuchilla.

NOTA: Protéjase las manos con guantes y/o envuelva la cuchilla con un paño grueso.

2. Retire el perno de la cuchilla girándolo hacia

la izquierda.

MOTOR

LUBRICACIÓN

Use sólo un aceite detergente de alta calidad calificado con la clasificación SG-SL de servicio de API. Seleccione el grado de viscosidad SAE del aceite de acuerdo con la temperatura de operación esperada.

The operation of any riding mower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your riding mower or performing any adjustments or repairs. We recommend a wide vision

00155 safety mask over spectacles or standard safety glasses.

3. Instale la nueva cuchilla con el diseño que

dice "ESTE LADO HACIA ARRIBA" hacia la

plataforma y el ensamblaje del mandril.

Mandril

Armado

	Cuchilla
Perno de
cuchilla
(especial)	Estrella
	Estrella
	Orificio central

IMPORTANTE: Para asegurar un ensamblaje correcto, el orificio central de la cuchilla se debe alinear con la estrella del ensamblaje del mandril.

4.Instale y ajuste bien el perno de la cuchilla (45 - 55 pies/ Libras).

IMPORTANTE: El perno de la cuchilla especial está tratado con calor.

BATERÍA

La cortadora de césped tiene un sistema de carga de la batería que es suficiente para el uso normal.

•Mantenga la batería y los conectores limpios.

•Sólo recargue la batería con un cargador aprobado para una batería de 2.8 amperes hora de 12V.

•Cargarla con cualquier otro cargador o con un cargador tipo automotriz puede causar un daño permanente en la batería.

•Cargue la batería durante 24 horas para que

se cargue por completo.

NOTA: La batería del equipo original de la corta- dora de césped no necesita mantenimiento. No intente abrir ni retirar los tapones o las cubiertas. Agregar o revisar el nivel del electrolito no es necesario.

ADVERTENCIA: No fuerce el arranque de la batería. Puede ocurrir un daño permanente en la batería o una lesión personal.

ENFRIAMIENTO DEL TRANSEJE

Mantenga el transeje libre de cualquier acumula- ción de suciedad y paja, lo que puede restringir el enfriamiento.

CINTA EN V

Revise la cinta en V para ver si está deteriorada o desgastada después de 100 horas de operación y cámbiela si es necesario. La cinta no es ajustable. Cambie la cinta si comienza a deslizarse por el desgaste.

CALIDADES DE VISCOSIDAD DE SAE

							SAE 30
			5W-30

F	-20	0			30 32 40		60	80	100
C	-30	-20		-10	0	10	20	30	40

GAMA DE TEMPERATURA ANTICIPADA ANTES DEL PROXIMO CAMBIO DE ACEITE

oil_visc_chart1_s

NOTA: Auque los aceites de viscosidad múltiple 5W30, 10W30, etc.) mejoran el arranque en climas fríos, los aceites provocarán un incremento en el consumo de aceite cuando se usan por encima de los 32°F (0°C). Revise el nivel de aceite del motor con más frecuencia para evitar cualquier posible daño en el motor debido a un nivel bajo de aceite. Cambie el aceite después de cada 25 horas de operación o al menos una vez al año si no se va a usar la cortadora de césped durante 25 horas en un año.

Revise el nivel de aceite del cárter antes de arrancar el motor y después de cada ocho (8) horas de operación. Apriete bien el tapón/la varilla de llenado del aceite cada vez que revise el nivel del aceite.

CAMBIO DE ACEITE DEL MOTOR

Determine el rango de temperatura esperado antes de cambiar el aceite. Todo el aceite debe cumplir con la clasificación SG-SL de servicio de API.

•Asegúrese de que la cortadora de césped esté sobre una superficie nivelada.

•El aceite se drenará con más libertad cuando esté tibio.

•El aceite se puede bombear desde el motor con una bomba de sifón mecánica o eléctrica.

1.Retire el tapón/la varilla de llenado del aceite. Tenga cuidado de no permitir que entre su- ciedad en el motor cuando cambie el aceite.

2.Inserte el extremo de la bomba en el recipiente del aceite.

3.Bombee el aceite del recipiente.

Tapón del aceite

Llenado de aceite

HOW TO USE YOUR RIDING MOWER

TO SET PARKING BRAKE

Your riding mower is equipped with an opera- tor presence sensing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.

1.Depress brake pedal all the way down and hold.

2.Depress parking brake lever and release pressure from brake pedal. Pedal should remain in brake position. Make sure parking brake will hold riding mower secure.

Parking Brake	Motion	Mower Height
Parking Brake	Control
Pedal-Push Down	Control
Pedal-Push Down	Lever	Adjustment
to "Engage"	Lever	Adjustment
to "Engage"

	Deck Clutch
Brake Pedal	Lever
Brake Pedal	"Disengaged"
"Engaged"	Position
Position	Deck Clutch
Brake Pedal	Lever
"Drive"	"Engaged"
Position	Position

STOPPING

MOWER BLADE -

•To stop mower blade, move deck clutch lever to disengaged position.

GROUND DRIVE -

•To stop ground drive, depress brake pedal all the way down.

ENGINE -

•Turn ignition key to “STOP” position and re- movekey.Alwaysremovekeywhenleaving riding mower to prevent unauthorized use.

IMPORTANT: Leaving the ignition switch in any position other than "STOP" will cause the battery to discharge and go dead.

NOTE: Under certain conditions when riding mower is standing idle with the engine run- ning, hot engine exhaust gases may cause “browning” of grass. To eliminate this pos- sibility, always stop engine when stopping riding mower on grass areas.

CAUTION: Always stop riding mower completely, as described above, before leaving the operator's position.

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is controlled by the motion control lever.

1.Start riding mower with clutch/brake pedal depressed and motion control lever in neutral (N) position.

2.Move motion control lever to desired position.

3.Slowly release clutch/brake pedal to start movement.

IMPORTANT: Bring riding mower to a com- plete stop before shifting or changing gears. Failure to do so will shorten the useful life of your transaxle.

TO ADJUST MOWER CUTTING HEIGHT

The position of the mower height deck lift lever determines the cutting height.

•Grasp lift lever.

•Press lift lever plunger with thumb and move lever to desired position.

The cutting height range is approximately 1-1/2 to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil condi- tions, height of grass and types of grass being mowed.

•The average lawn should be cut to ap- proximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

WE261 specifications

The Weed Eater WE261 is a robust and versatile string trimmer designed to tackle a variety of lawn care tasks with ease and efficiency. Aimed at both homeowners and landscaping professionals, the WE261 is built to handle the challenges of overgrown lawns and garden beds, providing powerful performance and reliability.

One of the standout features of the WE261 is its 26cc 2-cycle engine, which delivers ample power while maintaining a lightweight profile. This engine ensures that users can navigate through dense vegetation and thick weeds without compromising performance. The 2-cycle technology allows for efficient fuel usage, providing users with longer run times between refuels.

The WE261 is equipped with a dual line bump head, which automatically releases more line as needed. This feature enhances productivity by allowing the user to focus on trimming rather than manually adjusting the string. The .095-inch line diameter provides a thick cutting path, making it effective against stubborn weeds and tall grass.

Another significant characteristic of the WE261 is its ergonomic design. The trimmer features a padded hand grip and an adjustable handle, allowing users to customize their grip for maximum comfort and control. This is especially beneficial during extended use, as it minimizes fatigue and enhances maneuverability.

The trimmer also incorporates an easy-start technology, which simplifies the starting process. Users can enjoy quick and hassle-free starts with minimal effort required. This feature is particularly useful for those who may not have extensive experience with starting gas-powered equipment.

Durability is a key consideration in the design of the WE261. Constructed with high-quality materials, this weed eater is built to withstand the rigors of regular use. The robust build ensures that it can handle various outdoor conditions, making it a reliable option for any lawn care enthusiast.

In summary, the Weed Eater WE261 presents a combination of power, efficiency, and user-friendly features. With its strong 26cc engine, automatic dual line bump head, ergonomic design, and easy-start technology, it stands out as an exceptional choice for anyone looking to maintain a well-groomed lawn. Whether dealing with overgrown areas or simply keeping the yard tidy, the WE261 is up to the task, delivering performance that users can trust.