Cómo Configurar SU Cortadora DE Césped

INSTALACIÓN DE COLUMNA DE DIRECCIÓN

1.Inserte el eje de dirección en el montaje y apriete bien con el perno, la arandela y la tuerca provistas.

2.Inserte el pasador en el orificio del eje de dirección.

3.Deslice la cubierta de plástico sobre el eje de dirección y en su posición.

Eje de dirección

		Cubierta de
	Arandela	plástico
	Arandela
		Montaje
	Pasador	del eje de
	Pasador	dirección
		dirección
	Tuerca	Perno
	Tuerca

4.Deslice la cubierta de espuma de protección del eje de dirección sobre el eje.

5.Coloque las ruedas delanteras de la cortadora de césped de modo que apunten en línea recta hacia adelante.

Inserto	Tuerca
	Tuerca
Arandela	Volante
	Adaptador
	Cubierta de
	espuma

Eje de dirección

6.Retire el adaptador del volante y deslice el adaptador sobre el eje de dirección.

7.Presione el volante en su posición sobre el eje, instale la arandela grande y tuerca; apriete bien la tuerca.

8.Coloque bien el inserto del volante en el centro del volante.

INSTALACIÓN DEL ASIENTO

1.Gire el asiento hacia arriba y retírelo del empaque de cartón. Retire el empaque de cartón y deséchelo.

2.Coloque el asiento en la tabla del asiento de manera que el perno de reborde esté colocado sobre el orificio ranurado grande de la tabla.

3.Presione hacia abajo el asiento para colocar el perno de reborde en la ranura y jale el asiento hacia la parte posterior de la cortadora de césped.

4.Gire el asiento y la tabla hacia adelante y ensamble la perilla de ajuste y la arandela plana sin apretar. No apriete.

Asiento

Tabla de asiento

Perno de reborde

5.Baje el asiento a la posición de operación siéntese sobre él.

Arandela plana

02464

Perilla de ajuste

6.Deslice el asiento hasta que logre una posición cómoda, lo que le permitirá presionar el pedal del embrague/freno hasta el fondo.

7.Retírese del asiento sin mover su posición ajustada.

8.Eleve el asiento y apriete bien la perilla de ajuste.

REVISE LA BATERÍA

Asegúrese de que la batería esté bien sujeta- da, y que todos los cables estén bien conec- tados.

•La batería está ubicada debajo del asiento.

•La batería se ha cargado por completo en la fábrica antes de su instalación.

Asiento

Batería

TO ADJUST BRAKE

Your riding mower is equipped with an adjustable brake system which is mounted on the right side of the transaxle. If riding mower requires more than (4) feet stop- ping distance in highest gear on a lever dry concrete or paved surface, then brake must be adjusted.

1.Park riding mower on a level surface.

2.Release brake/parking pedal.

3.Measure distance between rotor and brake pad if distance between rotor and brake pad is more than .02" gap brake needs to be adjusted.

4.Tighten caliper nut until .02" gap is reached.

Rotor

Brake

Pad

Nut

NOTE: Feeler gauge may be necessary to get correct measurement.

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, move steering wheel and reassemble per instructions in the "INSTALL STEERING COLUMN"section of this manual.

TO REMOVE WHEEL FOR REPAIRS

FRONT WHEEL

1.Block up front axle securely.

2.Remove dust cover, retaining ring, and washer to allow wheel removal.

3.Repair tire and reassemble.

4.Replace washer and retaining ring securely in axle groove.

REAR WHEEL

1.Block up Rear axle securely.

2.Remove dust cover, retaining ring, wash- er, and square key while pulling tire off.

3.Repair tire and reassemble.

4.Replace square key while putting tire back on, then replace washer and retaining ring securely in axle groove ,when pushing tire back onto shaft reach under and pull chain sprocket toward you to ease tire replacement.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and use tire sealant. Tire sealant also prevents tire dry rot and corrosion.

Washer

Retaining

Ring

	Dust	Square Key
		(rear wheel only)
	Cover

TO START ENGINE WITH A WEAK BATTERY

CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smokingmaterialsawayfrombatteries.Always wear eye protection when around batteries. If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

NOTE: This unit is equipped with an engine recoil starting system that can be used if the battery is too weak to start. See “RECOIL STARTING SYSTEM” in operation section of this manual.

REPLACING BATTERY

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

WE261 specifications

The Weed Eater WE261 is a robust and versatile string trimmer designed to tackle a variety of lawn care tasks with ease and efficiency. Aimed at both homeowners and landscaping professionals, the WE261 is built to handle the challenges of overgrown lawns and garden beds, providing powerful performance and reliability.

One of the standout features of the WE261 is its 26cc 2-cycle engine, which delivers ample power while maintaining a lightweight profile. This engine ensures that users can navigate through dense vegetation and thick weeds without compromising performance. The 2-cycle technology allows for efficient fuel usage, providing users with longer run times between refuels.

The WE261 is equipped with a dual line bump head, which automatically releases more line as needed. This feature enhances productivity by allowing the user to focus on trimming rather than manually adjusting the string. The .095-inch line diameter provides a thick cutting path, making it effective against stubborn weeds and tall grass.

Another significant characteristic of the WE261 is its ergonomic design. The trimmer features a padded hand grip and an adjustable handle, allowing users to customize their grip for maximum comfort and control. This is especially beneficial during extended use, as it minimizes fatigue and enhances maneuverability.

The trimmer also incorporates an easy-start technology, which simplifies the starting process. Users can enjoy quick and hassle-free starts with minimal effort required. This feature is particularly useful for those who may not have extensive experience with starting gas-powered equipment.

Durability is a key consideration in the design of the WE261. Constructed with high-quality materials, this weed eater is built to withstand the rigors of regular use. The robust build ensures that it can handle various outdoor conditions, making it a reliable option for any lawn care enthusiast.

In summary, the Weed Eater WE261 presents a combination of power, efficiency, and user-friendly features. With its strong 26cc engine, automatic dual line bump head, ergonomic design, and easy-start technology, it stands out as an exceptional choice for anyone looking to maintain a well-groomed lawn. Whether dealing with overgrown areas or simply keeping the yard tidy, the WE261 is up to the task, delivering performance that users can trust.