Weed Eater WE261 warranty Check Tire Pressure, Check Deck Levelness, Check Brake System, Checklist

Page 8

NOTE: You may now roll your riding mower off the skid. Follow the appropriate instruction below to remove the riding mower from the skid.

WARNING: Before starting, read, un- derstand and follow all instructions in the Operation section of this manual. Be sure riding mower is in a well-ventilated area. Be sure the area in front of riding mower is clear of other people and objects.

TO ROLL RIDING MOWER OFF SKID (See Operation section for location and function of controls)

1.Raise deck lift lever to its highest position.

2.Release parking brake by depressing clutch/brake pedal.

3.Engage freewheel control. See “TO TRANSPORT” in the operation section of this manual.

4.Roll riding mower forward off skid.

CHECK TIRE PRESSURE

The tires on your riding mower were overin- flated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

•Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly leveled. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITON OF MOWER DRIVE BELT

See the figure that is shown for replacing the mower drive belt in the service and adjust- ment section of this manual. Verify that the belt is routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your riding mower, check to see that the brake is oper- ating properly. See “TO ADJUST BRAKE”

✓CHECKLIST

Before you operate your new riding mower, we wish to assure that you receive the best performance and satisfaction from this Quality Product.

Please review the following checklist:

✓All assembly instructions have been completed.

✓No remaining loose parts in carton.

✓Battery is properly connected.

✓Seat is adjusted comfortably and tight- ened securely.

✓All tires are properly inflated. (For ship- ping purposes, the tires were overinflated at the factory).

✓Be sure mower deck is properly leveled side-to-side/front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

✓Check mower belt. Be sure it is routed properly around pulleys and inside all belt keepers.

✓Check wiring. See that all connections are still secure and wires are properly clamped.

✓Before driving riding mower, be sure free- wheel control is in “transmission engaged” position (see “TO TRANSPORT” in the

Operation section of this manual). While learning how to use your riding mower, pay extra attention to the following important items:

✓Engine oil is at proper level.

✓Fuel tank is filled with fresh, clean, regular unleaded gasoline.

✓Become familiar with all controls, their location and function. Operate them before you start the engine.

✓Be sure brake system is in safe operating condition.

✓Be sure Operator Presence System and Reverse Operation System (ROS) are working properly (See the Operation and Maintenance sections in this manual).

NIVELACIÓN DE LA CARCASA DE LA COR- TADORA DE CÉSPED

Ajuste la cortadora de césped mientras esté es- tacionada en el suelo o en un camino nivelado. Asegúrese de que las llantas estén bien infladas (Observe la parte lateral de la llanta para verificar que la PSI sea correcta). Si las llantas están infladas de más o de menos, usted no podrá ajustar bien la cortadora de césped.

AJUSTE DE LADO A LADO

•Eleve la cortadora de césped a su posición más alta.

•Mida la distancia "A" desde la orilla inferior de la cortadora de césped al nivel del suelo en las esquinas frontales de la cortadora de césped.

•Para elevar el lado derecho de la cortadora de césped, apriete la tuerca de ajuste del eslabón del elevador.

•Para bajar el lado derecho de la cortadora de césped, afloje la tuerca de ajuste del eslabón del elevador.

NOTA: Cada vuelta completa de la tuerca de ajuste cambiará la altura de la cortadora de césped aproximadamente 3/16".

• Vuelva a revisar las medidas después del ajuste.

Orilla inferior de la cor-

Orilla inferior de la cor-

tadora de césped en

tadora de césped en

relación con el suelo

relación con el suelo

A

A

AJUSTE DEL FRENTE A LA PARTE POSTERIOR

IMPORTANTE: La plataforma debe estar nivelada de lado a lado.

Para obtener los mejores resultados de corte, la carcasa de la cortadora de césped se debe ajustar de modo que el frente esté aproxima- damente de 1/8” a 1/2” más abajo que la parte posterior cuando la cortadora de césped esté en su posición más alta.

Revise el ajuste del lado derecho de la cortadora de césped. Mida la distancia “F” directamente en frente y detrás del mandril en la orilla inferior de la carcasa de la cortadora de césped conforme se muestra.

•Cuando la distancia “F” esté de 1/8" a 1/2" más abajo en el frente que en la parte posterior, apriete la tuerca “H” contra el muñón en el eslabón frontal.

NOTA: Cada vuelta completa de "G" cambiará "F" aproximadamente 3/8".

•Vuelva a revisar el ajuste de lado a lado. Tuerca "H" Tuerca "G"

Muñón

CAMBIO DE CINTA DEL IMPULSOR DE LA CUCHILLA DE LA CORTADORA DE CÉSPED

RETIRO DE CINTA DEL IMPULSOR DE LA CORTADORA DE CÉSPED

1.Estacione la cortadora de césped sobre una superficie nivelada.

2.Accione el freno de estacionamiento.

3.Baje la cortadora de césped a su posición más baja.

4.Retire la cubierta del mandril desde la plataforma de la cortadora de césped.

5.Retire la placa del motor posterior de la unidad.

6.Retire la sujeción de la cinta posterior de la unidad.

7.Enrolle con cuidado la cinta sobre la parte superior del mandril de la cuchilla de la cortadora de césped.

8.Retire la cinta de las poleas guía.

Cinta de impulsor de la cortadora de césped

Sujeción de cinta

in the Service and Adjustments section of this manual.

8

FF

•Para bajar el frente de la carcasa de la cortadora de césped gire las tuercas “G” y “H” hacia la derecha.

•Cuando la distancia “F” esté de 1/8" a 1/2" más abajo en el frente que en la parte posterior, apriete la tuerca “H” contra el muñón en el eslabón frontal.

•Para elevar el frente de la carcasa de la corta- dora de césped gire las tuercas “G” y “H” hacia la izquierda.

Mandril

Poleas guía

 

9.Revise las poleas guía para ver que giren con libertad.

10.Retire la cinta de la polea del impulsor posterior.

INSTALACIÓN DE CINTA DEL IMPULSOR DE LA CORTADORA DE CÉSPED

Instale en reversa de acuerdo con las instruccio- nes de la sección "RETIRO DE LA CINTA DEL

45IMPULSOR DE LA CORTADORA DE CÉSPED".

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Operator’s Manual Manual de Operario 09.08.11 CLTable of Contents WarrantySafety Rules Tabla DE Solución DE ProblemasAlways wear eye protection when operat- ing machine General OperationIV. Service Safe Handling of Gasoline III. ChildrenAlmacenamiento Safety Rules Product SpecificationsGeneral Service Customer ResponsibilitiesTools Required for Assembly Unassembled PartsTo Remove Riding Mower from Carton Unpack CartonHOW to SET UP Your Riding Mower Install Steering Column Install SeatCheck Battery Slide steering shaft protective foam cover over shaftChecklist Check Tire PressureCheck Deck Levelness Check for Proper Positon of Mower Drive BeltServicio Y Ajustes OperationCortadora DE Césped Retiro DE LA Cortadora DE Instalación DE LA Cortadora DE CéspedKnow Your Riding Mower HOW to USE Your Riding Mower To Adjust Mower Cutting HeightTo SET Parking Brake StoppingUsing the Reverse Operation System To Operate MowerTo Stop Mower Blade Reverse Operation System ROSTo Start Engine MantenimientoBefore Starting the Engine Mowing Tips Recoil Starting SystemLeft hand side of mower should be used for trimming Sismtema DE Arranque ManualBefore Each USE MaintenanceGeneral Recommendations Riding Mower Brake OperationTires Axle and SpindlesEngine Clean AIR Screen CleaningAIR Filter MufflerService and Adjustments To Install MowerOperación Riding MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentMower Drive Belt Installation To Replace Mower Blade Drive BeltCómo Configurar SU Cortadora DE Césped To Adjust BrakeTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery Replacing BatteryPartes no Ensambladas EngineInterlocks and Relays To Replace FuseBattery Reglas DE Seguridad StorageEspecificaciones DEL Producto MowerTroubleshooting Chart Problem Cause CorrectionReglas DE Seguridad III. NiñosOperación General II. Operación EN PendientesOnly Ride UP and Down HILL, not Across Hill Degrees MAX Tabla DE ContenidoGarantía
Related manuals
Manual 20 pages 13.36 Kb Manual 40 pages 39.3 Kb

WE261 specifications

The Weed Eater WE261 is a robust and versatile string trimmer designed to tackle a variety of lawn care tasks with ease and efficiency. Aimed at both homeowners and landscaping professionals, the WE261 is built to handle the challenges of overgrown lawns and garden beds, providing powerful performance and reliability.

One of the standout features of the WE261 is its 26cc 2-cycle engine, which delivers ample power while maintaining a lightweight profile. This engine ensures that users can navigate through dense vegetation and thick weeds without compromising performance. The 2-cycle technology allows for efficient fuel usage, providing users with longer run times between refuels.

The WE261 is equipped with a dual line bump head, which automatically releases more line as needed. This feature enhances productivity by allowing the user to focus on trimming rather than manually adjusting the string. The .095-inch line diameter provides a thick cutting path, making it effective against stubborn weeds and tall grass.

Another significant characteristic of the WE261 is its ergonomic design. The trimmer features a padded hand grip and an adjustable handle, allowing users to customize their grip for maximum comfort and control. This is especially beneficial during extended use, as it minimizes fatigue and enhances maneuverability.

The trimmer also incorporates an easy-start technology, which simplifies the starting process. Users can enjoy quick and hassle-free starts with minimal effort required. This feature is particularly useful for those who may not have extensive experience with starting gas-powered equipment.

Durability is a key consideration in the design of the WE261. Constructed with high-quality materials, this weed eater is built to withstand the rigors of regular use. The robust build ensures that it can handle various outdoor conditions, making it a reliable option for any lawn care enthusiast.

In summary, the Weed Eater WE261 presents a combination of power, efficiency, and user-friendly features. With its strong 26cc engine, automatic dual line bump head, ergonomic design, and easy-start technology, it stands out as an exceptional choice for anyone looking to maintain a well-groomed lawn. Whether dealing with overgrown areas or simply keeping the yard tidy, the WE261 is up to the task, delivering performance that users can trust.
Top Page Image Contents