Weed Eater WELRVBA30 To Level Mower Housing, SIDE-TO-SIDE Adjustment, FRONT-TO-BACK Adjustment

Page 22

TO LEVEL MOWER HOUSING

Adjust the mower while riding mower is parked on level ground or driveway. Ensure tires are properly inflated. If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

Raise mower to its highest position.

Measure distance "A" from bottom edge of mower to ground level at front corners of mower.

Bottom Edge of

Bottom Edge of

Mower to Ground

Mower to Ground

A

A

To raise the right side of the mower, tighten lift link adjustment nut.

To lower the right side of the mower, loosen lift link adjustment nut.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

Recheck measurements after adjusting.

Adjustment Nut

Turn nut left

Turn nut right

to raise mower

to lower mower

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to side.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of riding mower. Measure distance “F” directly in front and behind the mandrel at bottom edge of mower housing as shown.

FF

To lower front of mower housing turn nuts “G” and “H” clockwise.

When distance “F” is 1/8" to 1/2" lower at front than rear, tighten nut “H” against trunnion on front link.

To raise front of mower housing turn nuts “G” and “H” counter clockwise.

When distance “F” is 1/8" to 1/2" lower at front than rear, tighten nut “H” against trunnion on front link.

NOTE: Each full turn of "G" will change "F" by approximately about 3/8".

• Recheck side-to-side adjustment.

Nut "H"

Trunnion

Nut "G"

PARA INSTALACIÓN DEL ASIENTO

1.Retire el perno y la arandela plana asegurando el asiento en el empaque de cartón y póngalo aparte para ensamblar el asiento a la cortadora de césped. Retire el empaque de cartón y deséchelo.

2.Coloque el asiento en la tabla del asiento de manera que las tres (3) almohadillas de la parte inferior estén colocadas sobre los orificios ranurados grandes de la tabla.

3.Presione hacia abajo el asiento para colocar las almohadillas en las ranuras y jale el asiento hacia la parte posterior de la cortadora de césped.

4.Levante el asiento y apriete bien el perno y la arandela plana.

5.Retire la cinta y deséchela.

6.Baje el asiento a la posición de operación siéntese sobre él. Presione el pedal de em- brague/freno completamente hasta abajo. Si la posición de operación no es cómoda, ajuste el asiento.

Ranurado

Cinta

Cojín

Arandela plana

Base del

Asiento

 

Palanca de

Perno Lengüeta

ajuste

PARA AJUSTAR EL ASIENTO

DEL FRENTE HACIA ATRÁS -

1.Siéntese en el asiento.

2.Levante la palanca de ajuste y deslice el asiento hasta que logre una posición cómo- da, lo que le permitirá presionar el pedal del embrague/freno hasta el fondo.

3.Libere la palanca para bloquear el asiento en su posición.

SOPORTE LUMBAR -

Afloje la perilla de ajuste lumbar.

Deslice el respaldo del asiento hacia arriba o hacia abajo a la posición más cómoda para bajar el soporte de la espalda.

Apriete la perilla de ajuste lumbar.

Perilla de ajuste

 

lumbar

Palanca de ajuste

NOTA: Ahora puede sacar la cortadora de césped de la tarima. Observe las siguientes instrucciones apropiadas para retirar la cortadora de césped de la tarima.

ADVERTENCIA: Antes de empezar, lea, entienda y siga todas las instrucciones de la sección de Operación de este manual. Asegúrese de que la cortadora de césped esté en un área bien ventilada. Asegúrese de que el área de enfrente de la cortadora de césped esté libre de gente y objetos.

PARA SACAR LA CORTADORA DE CÉS- PED DE LA TARIMA (Consulte la sección de Operación para ver la ubicación y función de los controles)

1.Eleve la palanca del elevador de la plataforma hasta su posición máxima.

2.Suelte el freno de estacionamiento al liberar el pedal del embrague/freno.

3.Cambie unidad a la posición de neutro.

4.Saque la cortadora de césped de la tarima.

22

35

Image 22
Contents Parts and Service 10.24.11 CLTable of Contents WarrantyAlways wear eye protection when operat- ing machine Safety RulesIdentificación DE Problemas General OperationIV. Service Safe Handling of Gasoline III. ChildrenGeneral Service Almacenamiento Safety RulesMotor Unassembled Parts Product SpecificationsCustomer Responsibilities HOW to SET UP Your Riding Mower ASSEMBLY/PRE-OPERATIONTools Required for Assembly To Remove Riding Mower from CartonFront and Back Install SeatTo Adjust Seat Lumbar SupportServicio Y Ajustes Operation LimpiezaEnfriamiento DEL Transeje Know Your Riding MowerBatería Cambio DE Aceite DEL Motor Cinta ENHOW to USE Your Riding Mower Mantenimiento To Operate on Hills Reverse Operation System ROSTo Attach Deflector To TransportBefore Starting the Engine Antes DEL Arranque DEL MotorTo Start Engine Colocación DEL Deflector Mowing TipsFuncionamiento Atrás ROS Operación EN ColinasGeneral Recommendations MaintenanceBefore Each USE Cómo Usar LA Cortadora DE Césped Conozca SU Cortadora DE Césped EngineCleaning OperaciónLista DE Revisión Service and AdjustmentsRiding Mower FRONT-TO-BACK Adjustment To Level Mower HousingSIDE-TO-SIDE Adjustment Para Instalación DEL AsientoENSAMBLADO/PREOPERACIÓN Retiro DE LA Cortadora DE Césped DE LA Caja DE CartónPartes no Ensambladas Mower BatteryReglas DE Seguridad Storage OtherIII. Niños Troubleshooting ChartReglas DE Seguridad IV. ServicioII. Operación EN Pendientes Operación GeneralUse siempre protección ocular cuando opere la máquina Garantía Operación Solución DE ProblemasTabla DE Contenido Only Ride UP and Down HILL, not Across Hill Degrees MAX
Related manuals
Manual 8 pages 63.88 Kb

WELRVBA30 specifications

The Weed Eater WELRVBA30 is an innovative lawn care tool designed for homeowners seeking efficient and reliable trimming solutions. This versatile electric string trimmer boasts a range of features, technologies, and characteristics tailored to enhance lawn maintenance while providing ease of use and environmental sustainability.

One of the standout features of the WELRVBA30 is its powerful 30cc 2-cycle engine, which ensures robust performance while trimming grass and weeds in various terrains. This engine delivers ample power and torque, allowing the user to tackle thick underbrush and overgrown areas with ease. The design is lightweight and well-balanced, making it highly maneuverable for extended periods.

Equipped with a cutting width of 16 inches, the trimmer allows for efficient coverage of larger areas at once. This generous cutting diameter means less time spent trimming and more time enjoying your well-maintained lawn. Additionally, the adjustable handle provides comfort and control, catering to users of different heights and preferences.

The WELRVBA30 features a dual-line bump feed system, enabling quick and easy line advancement. Simply bump the trimmer head against the ground, and new line extends automatically, minimizing downtime during use. This feature is particularly useful for large jobs and allows users to maintain productivity without frequent interruptions.

Durability is a hallmark of the WELRVBA30, which is built with high-quality materials designed to withstand the rigors of outdoor use. The trimmer's heavy-duty cutting head can handle tough vegetation, while the robust housing provides protection and longevity.

For environmental consciousness, the Weed Eater WELRVBA30 operates on a low-emission engine, significantly reducing harmful pollutants while providing excellent fuel efficiency. This aligns with the growing demand for eco-friendly lawn care solutions.

In summary, the Weed Eater WELRVBA30 is an exceptional tool that combines power, efficiency, and user-friendly features. Its robust engine, adjustable functionalities, and durable construction make it an ideal choice for homeowners looking to maintain their lawns with ease. Whether tackling small patches of grass or large, unruly areas, this trimmer ensures that the job is done efficiently and effectively.