Tiger RBF-2C manual Fitting Controls, Lever Unit

Page 40

ASSEMBLY

FITTING CONTROLS

The position of the lever unit inside the tractor cab depends largely upon the route of the cables between unit and control valve.

The control valve is mounted on the front face of the oil tank.

The cable normally can be routed through the rear cab window and should be as free of bends as possible. DO NOT PINCH CABLE IN CLOSED WINDOW.

NOTE: Avoid sharp bends. The rotor control cable must not have a bend of less than 150mm (6 in) radius.

If the tractor cab has special apertures for cables the lever unit should be through them before they are attached to the tractor cab.

Follow instructions below for fitting lever unit.

A. Pass lever unit and cable through suitable aperture in rear of tractor cab.

NOTE: It is essential not to drill mounting holes through any structural member of the safety cab.

B.Mount the unit securely on to the mounting bracket with bolts provided.

C.Finally, check levers for smooth operation in both directions. If any stiffness is felt or if levers do not return to center, check cable route for sharp bends.

NOTE: Whenever the machine is removed and the tractor is operated without the control valve unit in place, fit rubber beading (contained in the cab fitting kit) to the edge of the console mounting bracket to prevent risk of injury.

LEVER UNIT

A.Adjustment is provided at the cable attachment to the control valve.

B.Loosen locknut on the cable/valve connection flange FIGURE 3-5 (A).

C.Loosen the two capscrews holding the valve connection flange FIGURE 3-5 (B).

FIGURE 3-5

RBF-2C 07-04

Assembly Section 3-6

© 2004 Alamo Group Inc.

 

Page 39 Page 41
Image 40
Page 39 Page 41
Contents RBF-2C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety Peligro ¡LEA EL InstructivoAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards UN- LessSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 Parts Information See Your Tiger DealerTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 18 2 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety This Act Seeks DutiesOsha Regulations Employer ResponsibilitiesIntroduction Section Introduction Before Operating this MachineAssembly Section Tractor Requirements GeneralMachine Preparation Fitting Machine to Tractor Assembly Fitting PTO SectionFitting Controls Lever UnitHydraulic Systems Adjust Lever Pivot PositionFill Tank with OIL RBF-2C Assembly Section Fitting Rotor Unit Connecting the Motor Mechanical BreakoutHose Layout TwistsSharp Bends Chafing HosesFlexible Front Guard KIT Accumulator KITRBF 2C Assembly Section Bleeding Rams Initial RUNBleeding the First Ram Assembly Page Operation Section Connectingattaching Heads Operation Tiger Rear Mount Boom Operation InstructionsOperation Tractor Requirements Operator RequirementsTractor Requirements and Capabilities Shatter Proof Safety Windows Rops and Seat BeltOperator Thrown Object Protection Tractor Lighting and SMV EmblemGetting on and OFF the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Connecting Attaching Head to the Boom Dash Nominal Torque Value Size IN.LBS FT.LBSPRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceFrame Assembly Boom Unit Pre-Operation Inspection and ServiceBoom ARM Assembly Hydraulic Line Inspection Hydraulic PUMP/OIL ReservoirFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating Speed and Ground Speed Operating the Attached Mower HeadsRoller Height Grass FlailGround Level and Scrub Cutting lower roller to its maximum Operation Alternative Rotor Link Positions Grass CuttingHedge Trimming Stalling the RotorMotor Position TRACTOR, BOOM, and Attached Head Storage Shutting Down the Attached HeadTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section Lubrication GearboxGrease Points PTO Drive TubesFilter Replacement Power TAKE-OFF ShaftHoses and Rotor Drive Circuit Hydraulic OilsRotor Unit Hydraulic CylindersStorage Parking and RemovalClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-2C-OMWPL-07/04 Printed U.S.A

RBF-2C specifications

The Tiger RBF-2C is an advanced multi-role drone system designed to operate in a variety of environments, showcasing exceptional capabilities in reconnaissance, surveillance, and target acquisition. This UAV stands out due to its unique blend of advanced technologies and user-friendly features, making it suitable for both military and civilian applications.

One of the main features of the Tiger RBF-2C is its remarkable endurance. With the ability to fly for up to 20 hours on a single mission, it allows for extended operational reach, making it an advantageous asset for long-term surveillance and reconnaissance missions. This endurance is complemented by a payload capacity of up to 100 kilograms, which can include high-definition cameras, thermal imaging systems, and other specialized sensors.

The Tiger RBF-2C employs cutting-edge aerodynamics, featuring a sleek design that minimizes drag and enhances stability during flight. Its wings are equipped with advanced retractable winglets that can adjust based on flight conditions, further improving its performance. Additionally, the drone features a wide operational range, with the ability to operate effectively at altitudes of up to 20,000 feet, allowing it to gather intelligence in diverse geographical settings.

Another significant characteristic of the Tiger RBF-2C is its advanced communication and data-link systems. It utilizes secure and robust communication channels that ensure real-time data transmission without the risk of interception. This includes encrypted video feeds and telemetry data that can be accessed instantly by operators on the ground, facilitating timely decision-making.

The Tiger RBF-2C also incorporates an array of automated flight technologies that enhance its operational ease. Its intelligent autopilot system can execute complex flight profiles, including waypoint navigation and automatic return-to-home functions. Moreover, it can seamlessly integrate with existing command-and-control systems, making it an essential tool for modern military operations.

In terms of versatility, the Tiger RBF-2C can be deployed in various scenarios, from disaster response and environmental monitoring to military missions and border security. Its modular design allows for quick reconfiguration, enabling operators to adapt the drone for specific tasks as needed.

Overall, the Tiger RBF-2C stands out as a premier drone system encapsulating the future of unmanned aviation technology. Its impressive combination of endurance, advanced communication, automated systems, and versatility make it a formidable asset in both civilian and military operations, paving the way for smarter, more efficient aerial surveillance and reconnaissance.
Top Page Image Contents