Tiger RBF-2C manual Initial RUN, Bleeding Rams, Bleeding the First Ram

Page 48

ASSEMBLY

INITIAL RUN

A.Check that the motor hoses are connected together.

B.Run tractor engine at idle speed and engage PTO drive.

C.Increase PTO speed gradually up to 360 rev/min.

D.The pump will start operating during run-up. Flexing of the motor hoses and turbulence of the oil tank can be observed.

E.When pump is operating run system at 360 rev/min PTO speed for 10 minutes.

F.Check oil level. The oil level is correct when visible in the bottom of the filler assembly strainer.

BLEEDING RAMS

The ram cylinders at first will be full of air, therefore it may take some time for the cylinders to move after the control levers have been operated. Ensure sufficient space is available to allow for any unexpected movement of the arms.

Bleeding the First Ram

Due to the fact that the first arm can move past the vertical (overcenter) when fully raised, a restrictor may be fitted in the first ram hydraulic system to give a slow, controlled movement of the arm past center. It is essential that the first ram is fully bled to prevent fall back to the arm when the arms are stretched out and taken past vertical.

NOTE: The following instructions must be carried out before any attempt is made to raise more than one arm at a time.

A.Engage PTO drive with tractor engine at idle speed.

B.Increase PTO speed to 360-400 rev/min.

C.Fully retract second cylinder.

D.Fully retract the first cylinder.

E.Slacken hose connection at the bottom of the first cylinder.

G.Continue the bleeding until only clean, bubble-free oil is escaping from the fitting. Tighten fitting.

H.Open and close all cylinders to expel the air.

I.Check the oil level in the tank/tractor hydraulic oil reservoir and top up if necessary.

J.Check all hydraulic connections in the cylinder circuit for tightness.

WARNING! Do not raise more than one arm at a time until cylinders are completely free of air. Unex- pected movement of the arms can be dangerous.

RBF-2C 07-04

Assembly Section 3-14

© 2004 Alamo Group Inc.

 

Image 48
Contents RBF-2C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety Peligro ¡LEA EL InstructivoAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards UN- LessSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 Parts Information See Your Tiger DealerTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 18 2 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety This Act Seeks DutiesOsha Regulations Employer ResponsibilitiesIntroduction Section Introduction Before Operating this MachineAssembly Section General Tractor RequirementsMachine Preparation Fitting Machine to Tractor Assembly Fitting PTO SectionFitting Controls Lever UnitAdjust Lever Pivot Position Hydraulic SystemsFill Tank with OIL RBF-2C Assembly Section Fitting Rotor Unit Connecting the Motor Mechanical BreakoutHose Layout TwistsSharp Bends Chafing HosesFlexible Front Guard KIT Accumulator KITRBF 2C Assembly Section Initial RUN Bleeding RamsBleeding the First Ram Assembly Page Operation Section Connectingattaching Heads Operation Tiger Rear Mount Boom Operation InstructionsOperation Operator Requirements Tractor RequirementsTractor Requirements and Capabilities Shatter Proof Safety Windows Rops and Seat BeltOperator Thrown Object Protection Tractor Lighting and SMV EmblemGetting on and OFF the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Connecting Attaching Head to the Boom Dash Nominal Torque Value Size IN.LBS FT.LBSPRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBoom Unit Pre-Operation Inspection and Service Frame AssemblyBoom ARM Assembly Hydraulic Line Inspection Hydraulic PUMP/OIL ReservoirFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating Speed and Ground Speed Operating the Attached Mower HeadsGrass Flail Roller HeightGround Level and Scrub Cutting lower roller to its maximum Operation Alternative Rotor Link Positions Grass CuttingHedge Trimming Stalling the RotorMotor Position TRACTOR, BOOM, and Attached Head Storage Shutting Down the Attached HeadTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section Lubrication GearboxGrease Points PTO Drive TubesFilter Replacement Power TAKE-OFF ShaftHoses and Rotor Drive Circuit Hydraulic OilsRotor Unit Hydraulic CylindersStorage Parking and RemovalClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-2C-OMWPL-07/04 Printed U.S.A

RBF-2C specifications

The Tiger RBF-2C is an advanced multi-role drone system designed to operate in a variety of environments, showcasing exceptional capabilities in reconnaissance, surveillance, and target acquisition. This UAV stands out due to its unique blend of advanced technologies and user-friendly features, making it suitable for both military and civilian applications.

One of the main features of the Tiger RBF-2C is its remarkable endurance. With the ability to fly for up to 20 hours on a single mission, it allows for extended operational reach, making it an advantageous asset for long-term surveillance and reconnaissance missions. This endurance is complemented by a payload capacity of up to 100 kilograms, which can include high-definition cameras, thermal imaging systems, and other specialized sensors.

The Tiger RBF-2C employs cutting-edge aerodynamics, featuring a sleek design that minimizes drag and enhances stability during flight. Its wings are equipped with advanced retractable winglets that can adjust based on flight conditions, further improving its performance. Additionally, the drone features a wide operational range, with the ability to operate effectively at altitudes of up to 20,000 feet, allowing it to gather intelligence in diverse geographical settings.

Another significant characteristic of the Tiger RBF-2C is its advanced communication and data-link systems. It utilizes secure and robust communication channels that ensure real-time data transmission without the risk of interception. This includes encrypted video feeds and telemetry data that can be accessed instantly by operators on the ground, facilitating timely decision-making.

The Tiger RBF-2C also incorporates an array of automated flight technologies that enhance its operational ease. Its intelligent autopilot system can execute complex flight profiles, including waypoint navigation and automatic return-to-home functions. Moreover, it can seamlessly integrate with existing command-and-control systems, making it an essential tool for modern military operations.

In terms of versatility, the Tiger RBF-2C can be deployed in various scenarios, from disaster response and environmental monitoring to military missions and border security. Its modular design allows for quick reconfiguration, enabling operators to adapt the drone for specific tasks as needed.

Overall, the Tiger RBF-2C stands out as a premier drone system encapsulating the future of unmanned aviation technology. Its impressive combination of endurance, advanced communication, automated systems, and versatility make it a formidable asset in both civilian and military operations, paving the way for smarter, more efficient aerial surveillance and reconnaissance.