Trouble Shooting Guide | Tiger RBF-2C instruction

OPERATION

Use adequately sized and rated trailers and equipment to transport the tractor and mower. Consult an authorized dealer to determine the proper equipment required. Using adequately sized chains, heavy duty straps, cables and/or binders. Securely tie down both the front and rear of the tractor utilizing the proper tie down locations as specified by the tractor manufacturer.

Arrange the chains so that when tightened, the chains are pulling downward and against themselves. Carefully tighten the securing chains or other fasteners used as much as possible using boomers or binders to apply maximum tension. Use extreme care when attaching and removing the securing devices as the extreme tension involved when released has the potential to inflict serious injury.

While hauling the tractor and mower, make occasional stops to check that the tractor and mower have not moved or shifted and that the securing chains have maintained tension. If during transport a hard braking, sharp turning, or swerving action was performed, stop at the next safe location to inspect the security of the load.

12.TROUBLE SHOOTING GUIDE

A.HYDRAULIC CYLINDER NOT WORKING - Check level of hydraulic fluid (see sight gauge on tank). Check to see if pump is functioning properly by attempting to use another cylinder or pressure gauge. If pump is working properly, check the pressure on the line. The relief valve may be by-passing fluid at too low pressures. If cylinder is still not functioning properly, check the line for stoppage. The pistons in hydraulic cylinders are virtually trouble-free, but occasionally one will have a scored wall and allow oil to flow around the piston. In this case, replace the cylinder.

NOTE: Refer to repair parts section on valve bank settings on individual relief cartridges.

B.HYDRAULIC MOTOR NOT WORKING - Check lines for kinks or pinched place. If the motor is “bogging down” under load, recheck the relief valve setting on the cutter valve - 2500 P.S.I.

C.HYDRAULIC VALVE - Failures in the hydraulic system are almost always caused by other elements in the

system other than the valve; so the entire system should be checked before the valve is changed. A malfunction In any hydraulic valve section will require replacement of that section (but not the replacement of the valve bank) since the insides are honed to fit individually. Attachments such as the relief valves and detent may be serviced individually.

D.STRUCTURAL MEMBERS - Failure in structural members generally results from rough treatment. While they are constructed to withstand abuse, they cannot be made strong enough to withstand abnormal abuse. The factory does not warrant these parts to any extent other than in normal use in grass, weeds, brush, small bushes, and small trees which the unit is designed to cut.

RBF-2C 07/04	Operation Section 4-31
© 2004 Alamo Group Inc.

RBF-2C specifications

The Tiger RBF-2C is an advanced multi-role drone system designed to operate in a variety of environments, showcasing exceptional capabilities in reconnaissance, surveillance, and target acquisition. This UAV stands out due to its unique blend of advanced technologies and user-friendly features, making it suitable for both military and civilian applications.

One of the main features of the Tiger RBF-2C is its remarkable endurance. With the ability to fly for up to 20 hours on a single mission, it allows for extended operational reach, making it an advantageous asset for long-term surveillance and reconnaissance missions. This endurance is complemented by a payload capacity of up to 100 kilograms, which can include high-definition cameras, thermal imaging systems, and other specialized sensors.

The Tiger RBF-2C employs cutting-edge aerodynamics, featuring a sleek design that minimizes drag and enhances stability during flight. Its wings are equipped with advanced retractable winglets that can adjust based on flight conditions, further improving its performance. Additionally, the drone features a wide operational range, with the ability to operate effectively at altitudes of up to 20,000 feet, allowing it to gather intelligence in diverse geographical settings.

Another significant characteristic of the Tiger RBF-2C is its advanced communication and data-link systems. It utilizes secure and robust communication channels that ensure real-time data transmission without the risk of interception. This includes encrypted video feeds and telemetry data that can be accessed instantly by operators on the ground, facilitating timely decision-making.

The Tiger RBF-2C also incorporates an array of automated flight technologies that enhance its operational ease. Its intelligent autopilot system can execute complex flight profiles, including waypoint navigation and automatic return-to-home functions. Moreover, it can seamlessly integrate with existing command-and-control systems, making it an essential tool for modern military operations.

In terms of versatility, the Tiger RBF-2C can be deployed in various scenarios, from disaster response and environmental monitoring to military missions and border security. Its modular design allows for quick reconfiguration, enabling operators to adapt the drone for specific tasks as needed.

Overall, the Tiger RBF-2C stands out as a premier drone system encapsulating the future of unmanned aviation technology. Its impressive combination of endurance, advanced communication, automated systems, and versatility make it a formidable asset in both civilian and military operations, paving the way for smarter, more efficient aerial surveillance and reconnaissance.