Woods Equipment MDO80-2 manual Joint Assembly

Page 25

CD1386

Figure 15

CD1387

Figure 16

CD1388

Figure 17

2.With snap rings removed, support drive in vise, hold yoke in hand and tap on yoke to drive cup up out of yoke. See Figure 15.

3.Clamp cup in vise as shown in Figure 16 and tap on yoke to completely remove cup from yoke. Repeat steps two and three for opposite cup.

4.Place universal cross in vise as shown in Figure 17 and tap on yoke to remove cup. Repeat step three for final removal. Drive remaining cup out with a drift and hammer.

U-Joint Assembly

1.Place seals securely on bearing cups. Insert cup into yoke from outside and press in with hand pressure as far as possible. Insert journal cross into bearing cup with grease fitting away from shaft. Be careful not to disturb needle bearings. Insert another bearing cup directly across from first cup and press in as far as possible with hand pressure.

Trap cups in vise and apply pressure. Be sure jour- nal cross is started into bearings and continue pressure with vise, squeezing in as far as possible. Tap yoke to aid in process.

2.Seat cups by placing a drift or socket (slightly smaller than the cup) on cup and rapping with a hammer. See Figure 18. Install snap ring and repeat on opposite cup.

3.Repeat steps one and two to install remaining cups in remaining yoke.

Move both yokes in all directions to check for free movement. Should movement be restricted, rap on yokes sharply with a hammer to relieve any ten- sion. Repeat until both yokes move in all directions without restriction.

CD1389

Figure 18

15916 (Rev. 5/11/2007)

Dealer Service 25

 

 

Image 25
Contents Rotary Cutter To the Dealer IntroductionLEA EL Instructivo Table of ContentsTractor Requirements SpecificationsGeneral Information Safety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishPreparation Safety RulesTraining Operation MaintenanceTransportation Storage Serial Number Plate Safety & Instructional DecalsRED Rear Reflector To Avoid Serious Injury or DeathBe Careful Rotating Blades Thrown ObjectsOperation OperationTractor Stability Attaching Cutter to Tractor 3-POINT ModelsShorten Driveline Driveline AttachmentCutting Height Adjustment Without Tailwheel or Check Chains Cutting Height Adjustment for MD80 Mounted Cutter FigureCutting Height Adjustment With Tailwheel or Check Chains Attaching Cutter to Tractor PULL-TYPE Models Cutting Height Adjustment for D80 Pull-Type Cutter FigurePRE-OPERATION Check List Starting and Stopping CutterOperating Technique CleaningOwners Service Owner ServiceLubrication Information Figure Blade Removal Figure Blade Servicing FigureBelt Installation Figure Blade InstallationBlade Sharpening Chain ShieldingSplit Rim Tire Servicing Servicing Tires SafelyDealer Service Dealer ServiceGearbox Maintenance Gearbox Adjustment Gearbox AssemblyAssembly Blade Spindle Repair FigureJoint Disassembly Shield Bearing ServiceUniversal Joint Repair Joint Assembly Servicing Tires Safely Problem Possible Cause Solution Trouble ShootingAssembly AssemblyBlade Installation Figure Distribution Baffle Installation FigureWheel Yoke Installation for DO80-2 Pull- Type Cutter Figure Chain Shielding Installation FigureGearbox Lubrication Tongue and H-Frame Assembly Optional Hydraulic Lift Assembly Tongue Installation for DO80-2 Pull-Type Cutter FigureDriveline Installation MD80 Assembly FigureFrame and Lift Installation Optional Leaf Mulcher Installation FigureOptional Check Chain Installation Optional Check Chain Installation FigureDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListDealer Check Lists Parts Index to Parts ListPart QTY Description DO80-2 Main Frame Assembly PULL-TYPEMDO80-2 Main Frame Assembly Mounted Model DO80-2 & MDO80-2 Main Frame Assembly Common Parts 2390 DO80-2 Front 2/3 of 3-JOINT Drive Square Shaft DO80-2 Front 2/3 of 3-JOINT Drive TWO-LOBE Shaft DO80-2 & MDO80-2 Rear Section of Univeral Drive MDO80-2 Front 1/2 of Universal DriveGearbox Repair Kit DO80-2 & MDO80-2 Gearbox AssemblyDO80-2 & MDO80-2 Blades DO80-2 & MDO80-2 Blade Spindle AssemblyDO80-2 & MDO80-2 Chain Shielding Assembly DO80-2 Parking Jack DO80-2 & MDO80-2 Idler Pulley AssemblyDO80-2 SPRING-LOADED Wheel Yoke DO80-2 Height Adjustment CrankDO80-2 Laminated Tire with HUB & Axle DO80-2 RIM & Axle AssemblySOL ID T IRE DO80-2 Aircraft Tire & HUBMDO80-2 Tailwheel Assembly DO80-2 Hydraulic Hose KIT & Fittings Optional DO80-2 Pivot Link KIT OptionalDO80-2 3-1/2 X 8 Hydraulic Cylinder #10475 Optional MDO80-2 Check Chain Assembly Optional DO80-2 & MDO80-2 Leaf Mulcher Assembly OptionalMDO80-2 Category 2 Bushing KIT MDO80-2 Category 2 Hitch PIN OptionsParts SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Warranty

DO80-2, MDO80-2 specifications

The Woods Equipment MDO80-2 and DO80-2 are robust and innovative pieces of machinery designed to meet the demands of both commercial and agricultural applications. Renowned for their efficiency and performance, these models have garnered attention for their advanced features and technologies that enhance productivity.

One of the standout characteristics of the MDO80-2 and DO80-2 is their powerful cutting capabilities. Equipped with a heavy-duty steel frame, both models provide exceptional durability, allowing them to withstand rigorous use in various conditions. The cutting decks are designed for superior grass trimming, reducing the need for multiple passes and saving valuable time. The adjustable cutting height offers versatility, accommodating different grass types and lengths, ensuring a flawless finish every time.

Another key feature of these models is their advanced blade technology. The blades are crafted from high-quality steel, increasing their longevity and performance. The designs enable clean cuts, promoting healthier grass growth and enhancing the overall appearance of lawns and fields. Additionally, the MDO80-2 is equipped with a double-blade system, which further enhances cutting efficiency and reduces clumping.

The MDO80-2 and DO80-2 also prioritize user comfort and ease of operation. They come with ergonomic controls that ease the strain on operators during extended use. The intuitive design of the control panel simplifies operation, allowing users to focus on their tasks without getting bogged down by complicated settings.

For enhanced maneuverability, both models feature a smooth turning radius, making them ideal for navigating tight spaces. Whether working in a residential yard or a larger agricultural field, operators benefit from the agility these machines provide.

In terms of maintenance, Woods Equipment has developed the MDO80-2 and DO80-2 with user-friendliness in mind. The models are designed for easy access to critical components, simplifying routine maintenance tasks. This design philosophy not only prolongs the lifespan of the equipment but also minimizes downtime.

Overall, the Woods Equipment MDO80-2 and DO80-2 are exceptional choices for those seeking high-performance mowing solutions. With their durable construction, advanced cutting technologies, and user-friendly features, these models are well-suited for fulfilling the demands of any mowing operation, making them a reliable investment for years to come.