Woods Equipment MDO80-2 manual Tongue Installation for DO80-2 Pull-Type Cutter Figure

Page 31

Tongue Installation for DO80-2 Pull-Type Cutter (Figure 24)

Attach compression bracket (7) to front of gearbox stand with lock washers (20) and nuts (21).

Align holes in tongue (1) to bottom hole of mast plate

(6)and insert bushing (14) through the holes, then place washer (13) on bolt (12) and insert through mast plate, bushing and tongue. Install lock washer (15) over bolt and attach with nut (16).

Support tongue by attaching jack (27).

Attach compression member (4) to compression bracket (7) with clevis pin (25) and cotter pin (17), then attach front end to tongue with bolt (19), lock washer

(20)and nut (21). The compression member setting must be adjusted when the cutting height is set.

Align H-frame (5) to tongue (1) and attach with clevis pin (18) and two cotter pins (17).

Place key in gearbox input shaft, loosen clamp bolt (11) on rear of driveline, and slide driveline onto gearbox input shaft. Tighten clamp bolt and install cotter pin (30) through driveline and input shaft. Snap rear tether chain (32) around the compression link to prevent driv- eline shield rotation.

Align driveline in H-frame and insert clevis pin (22) through H-frame and carrier bearing (9). Attach by inserting two cotter pins (17) in clevis pin (22). Snap middle tether chain (32) around H-frame to prevent driveline shield rotation.

Attach rear universal joint shield (8) to gear stand as shown with bolts (28), washers (33) and nuts (31).

Place forward driveline shield, (10) over H-Frame and attach with lock washer (29) and bolt (28)

Attach pipe (24) to H-frame using bolt (28), lock washer

(20)and nut (21). Attach front tether chain (32) securely to tractor.

Optional Hydraulic Installation for DO80-2 Pull-Type Cutter (Figure 25)

Remove the crank (7) from pivot link holder (6), insert pivot link (5) into pivot link holder (6), then install the crank and cotter pin (8).

Remove bolt (2) from H-frame, install hydraulic hose holder (3), and install bolt.

Install hydraulic cylinder (9) using clevis pins (11), then route hose through hose holder (3).

1.

Pivot link kit

8.

1/4 x 1-1/2"

2.

1/2 x 5-1/2" Bolt

 

Cotter pin

3.

Hose holder

9.

Cylinder

4.

1/2" Hex nut

10.

H-Frame

5.

Pivot link

11.

Clevis pin

6.

Pivot link holder

12.

Pivot nut

7.

Crank

 

 

 

 

 

 

Figure 25. Optional Hydraulic Lift Assembly

15916 (Rev. 3/30/2007)

Assembly 31

 

 

Image 31
Contents Rotary Cutter To the Dealer IntroductionLEA EL Instructivo Table of ContentsTractor Requirements SpecificationsGeneral Information Safety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishPreparation Safety RulesTraining Operation MaintenanceTransportation Storage Serial Number Plate Safety & Instructional DecalsRED Rear Reflector To Avoid Serious Injury or DeathBe Careful Rotating Blades Thrown ObjectsAttaching Cutter to Tractor 3-POINT Models OperationOperation Tractor StabilityShorten Driveline Driveline AttachmentCutting Height Adjustment Without Tailwheel or Check Chains Cutting Height Adjustment for MD80 Mounted Cutter FigureCutting Height Adjustment With Tailwheel or Check Chains Starting and Stopping Cutter Cutting Height Adjustment for D80 Pull-Type Cutter FigureAttaching Cutter to Tractor PULL-TYPE Models PRE-OPERATION Check ListOperating Technique CleaningOwners Service Owner ServiceLubrication Information Figure Blade Removal Figure Blade Servicing FigureChain Shielding Blade InstallationBelt Installation Figure Blade SharpeningSplit Rim Tire Servicing Servicing Tires SafelyDealer Service Dealer ServiceGearbox Maintenance Blade Spindle Repair Figure Gearbox AssemblyGearbox Adjustment AssemblyJoint Disassembly Shield Bearing ServiceUniversal Joint Repair Joint Assembly Servicing Tires Safely Problem Possible Cause Solution Trouble ShootingDistribution Baffle Installation Figure AssemblyAssembly Blade Installation FigureWheel Yoke Installation for DO80-2 Pull- Type Cutter Figure Chain Shielding Installation FigureGearbox Lubrication Tongue and H-Frame Assembly Optional Hydraulic Lift Assembly Tongue Installation for DO80-2 Pull-Type Cutter FigureDriveline Installation MD80 Assembly FigureFrame and Lift Installation Optional Leaf Mulcher Installation FigureOptional Check Chain Installation Optional Check Chain Installation FigureDelivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListDealer Check Lists Parts Index to Parts ListPart QTY Description DO80-2 Main Frame Assembly PULL-TYPEMDO80-2 Main Frame Assembly Mounted Model DO80-2 & MDO80-2 Main Frame Assembly Common Parts 2390 DO80-2 Front 2/3 of 3-JOINT Drive Square Shaft DO80-2 Front 2/3 of 3-JOINT Drive TWO-LOBE Shaft DO80-2 & MDO80-2 Rear Section of Univeral Drive MDO80-2 Front 1/2 of Universal DriveGearbox Repair Kit DO80-2 & MDO80-2 Gearbox AssemblyDO80-2 & MDO80-2 Blades DO80-2 & MDO80-2 Blade Spindle AssemblyDO80-2 & MDO80-2 Chain Shielding Assembly DO80-2 Parking Jack DO80-2 & MDO80-2 Idler Pulley AssemblyDO80-2 SPRING-LOADED Wheel Yoke DO80-2 Height Adjustment CrankDO80-2 Laminated Tire with HUB & Axle DO80-2 RIM & Axle AssemblySOL ID T IRE DO80-2 Aircraft Tire & HUBMDO80-2 Tailwheel Assembly DO80-2 Hydraulic Hose KIT & Fittings Optional DO80-2 Pivot Link KIT OptionalDO80-2 3-1/2 X 8 Hydraulic Cylinder #10475 Optional MDO80-2 Check Chain Assembly Optional DO80-2 & MDO80-2 Leaf Mulcher Assembly OptionalMDO80-2 Category 2 Bushing KIT MDO80-2 Category 2 Hitch PIN OptionsParts Metric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty Warranty

DO80-2, MDO80-2 specifications

The Woods Equipment MDO80-2 and DO80-2 are robust and innovative pieces of machinery designed to meet the demands of both commercial and agricultural applications. Renowned for their efficiency and performance, these models have garnered attention for their advanced features and technologies that enhance productivity.

One of the standout characteristics of the MDO80-2 and DO80-2 is their powerful cutting capabilities. Equipped with a heavy-duty steel frame, both models provide exceptional durability, allowing them to withstand rigorous use in various conditions. The cutting decks are designed for superior grass trimming, reducing the need for multiple passes and saving valuable time. The adjustable cutting height offers versatility, accommodating different grass types and lengths, ensuring a flawless finish every time.

Another key feature of these models is their advanced blade technology. The blades are crafted from high-quality steel, increasing their longevity and performance. The designs enable clean cuts, promoting healthier grass growth and enhancing the overall appearance of lawns and fields. Additionally, the MDO80-2 is equipped with a double-blade system, which further enhances cutting efficiency and reduces clumping.

The MDO80-2 and DO80-2 also prioritize user comfort and ease of operation. They come with ergonomic controls that ease the strain on operators during extended use. The intuitive design of the control panel simplifies operation, allowing users to focus on their tasks without getting bogged down by complicated settings.

For enhanced maneuverability, both models feature a smooth turning radius, making them ideal for navigating tight spaces. Whether working in a residential yard or a larger agricultural field, operators benefit from the agility these machines provide.

In terms of maintenance, Woods Equipment has developed the MDO80-2 and DO80-2 with user-friendliness in mind. The models are designed for easy access to critical components, simplifying routine maintenance tasks. This design philosophy not only prolongs the lifespan of the equipment but also minimizes downtime.

Overall, the Woods Equipment MDO80-2 and DO80-2 are exceptional choices for those seeking high-performance mowing solutions. With their durable construction, advanced cutting technologies, and user-friendly features, these models are well-suited for fulfilling the demands of any mowing operation, making them a reliable investment for years to come.