Woods Equipment MDO80-2 Optional Leaf Mulcher Installation Figure, Frame and Lift Installation

Page 33

and elastic stop nuts (21). Attach tailwheel assembly

(20)to tailwheel bracket (34) with clevis pin (33) and secure with two cotter pins (31).

Attach tailwheel arm brackets (19) to tailwheel assem- bly (20) with bolt (18) and elastic stop nut (21).

A-Frame and Lift Installation

Place washers (24) on bolts (23), insert through bracket (26) and tighten bolts into nuts welded to gear stand.

Bolt rebound pad (28) to rebound pad support (27). Insert bolt (9) through gear stand and bracket (26), then place rebound pad assembly on top and secure with lock nuts (10). Use clevis pin (25) to attach hitch stop (17) to bracket (26), and secure with cotter pins (31).

Attach one end of each support brace (5) to the gear stand with bolts (9) and lock nuts (10). Insert hitch pins

(1)through mast plates (2). Place A-frame arms (3) over hitch pins, then install sleeve (4) and brace (5) over pin and secure with slotted hex nut (8).

Place spacer (13) between brackets on lift channel (12) and mount between lower holes of A-frame halves with

bolt (11) and lock nut (14). Attach lift channel to hitch stop (17) with clevis pin (16) and cotter pin (31).

OPTIONAL LEAF MULCHER

INSTALLATION (FIGURE 27)

Loosely assemble the leaf mulcher to the cutter before tightening any hardware.

The mulcher uses the chain shielding attachment holes. It is your option to remove or leave the chain shielding in place.

Place adapter (4) underneath the front edge of cutter and attach with bolts (6) and flange lock nuts (7).

Bolt front shield (3) to adapter using bolts (6) and flange lock nuts (7).

Place rear mulcher section (1) underneath the rear edge of cutter and attach with bolts (6) and flange lock nuts (7).

Attach right and left side frames (2 & 5) to the front and rear mulcher sections with bolts (6) and flange lock nuts (7). The slots are to the front and the U-section points outward as shown.

When all hardware is installed, you may tighten it.

1.Rear mulcher section

2.Left side frame

3.Front shield

4.Adapter

5.Right side frame

6.1/2 x 1" Bolt

7.1/2" Lock nut

Figure 27. Optional Leaf Mulcher Installation

15916 (Rev. 3/30/2007)

Assembly 33

 

 

Image 33
Contents Rotary Cutter To the Dealer IntroductionLEA EL Instructivo Table of ContentsSpecifications Tractor RequirementsGeneral Information Safety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishSafety Rules PreparationTraining Maintenance OperationTransportation Storage Serial Number Plate Safety & Instructional DecalsRED Rear Reflector To Avoid Serious Injury or DeathBe Careful Rotating Blades Thrown ObjectsOperation OperationTractor Stability Attaching Cutter to Tractor 3-POINT ModelsShorten Driveline Driveline AttachmentCutting Height Adjustment for MD80 Mounted Cutter Figure Cutting Height Adjustment Without Tailwheel or Check ChainsCutting Height Adjustment With Tailwheel or Check Chains Attaching Cutter to Tractor PULL-TYPE Models Cutting Height Adjustment for D80 Pull-Type Cutter FigurePRE-OPERATION Check List Starting and Stopping CutterOperating Technique CleaningOwner Service Owners ServiceLubrication Information Figure Blade Removal Figure Blade Servicing FigureBelt Installation Figure Blade InstallationBlade Sharpening Chain ShieldingSplit Rim Tire Servicing Servicing Tires SafelyDealer Service Dealer ServiceGearbox Maintenance Gearbox Adjustment Gearbox AssemblyAssembly Blade Spindle Repair FigureShield Bearing Service Joint DisassemblyUniversal Joint Repair Joint Assembly Servicing Tires Safely Problem Possible Cause Solution Trouble ShootingAssembly AssemblyBlade Installation Figure Distribution Baffle Installation FigureChain Shielding Installation Figure Wheel Yoke Installation for DO80-2 Pull- Type Cutter FigureGearbox Lubrication Tongue and H-Frame Assembly Optional Hydraulic Lift Assembly Tongue Installation for DO80-2 Pull-Type Cutter FigureDriveline Installation MD80 Assembly FigureFrame and Lift Installation Optional Leaf Mulcher Installation FigureOptional Check Chain Installation Optional Check Chain Installation FigureDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListDealer Check Lists Parts Index to Parts ListPart QTY Description DO80-2 Main Frame Assembly PULL-TYPEMDO80-2 Main Frame Assembly Mounted Model DO80-2 & MDO80-2 Main Frame Assembly Common Parts 2390 DO80-2 Front 2/3 of 3-JOINT Drive Square Shaft DO80-2 Front 2/3 of 3-JOINT Drive TWO-LOBE Shaft DO80-2 & MDO80-2 Rear Section of Univeral Drive MDO80-2 Front 1/2 of Universal DriveGearbox Repair Kit DO80-2 & MDO80-2 Gearbox AssemblyDO80-2 & MDO80-2 Blades DO80-2 & MDO80-2 Blade Spindle AssemblyDO80-2 & MDO80-2 Chain Shielding Assembly DO80-2 Parking Jack DO80-2 & MDO80-2 Idler Pulley AssemblyDO80-2 SPRING-LOADED Wheel Yoke DO80-2 Height Adjustment CrankDO80-2 Laminated Tire with HUB & Axle DO80-2 RIM & Axle AssemblySOL ID T IRE DO80-2 Aircraft Tire & HUBMDO80-2 Tailwheel Assembly DO80-2 Hydraulic Hose KIT & Fittings Optional DO80-2 Pivot Link KIT OptionalDO80-2 3-1/2 X 8 Hydraulic Cylinder #10475 Optional MDO80-2 Check Chain Assembly Optional DO80-2 & MDO80-2 Leaf Mulcher Assembly OptionalMDO80-2 Category 2 Bushing KIT MDO80-2 Category 2 Hitch PIN OptionsParts SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Warranty

DO80-2, MDO80-2 specifications

The Woods Equipment MDO80-2 and DO80-2 are robust and innovative pieces of machinery designed to meet the demands of both commercial and agricultural applications. Renowned for their efficiency and performance, these models have garnered attention for their advanced features and technologies that enhance productivity.

One of the standout characteristics of the MDO80-2 and DO80-2 is their powerful cutting capabilities. Equipped with a heavy-duty steel frame, both models provide exceptional durability, allowing them to withstand rigorous use in various conditions. The cutting decks are designed for superior grass trimming, reducing the need for multiple passes and saving valuable time. The adjustable cutting height offers versatility, accommodating different grass types and lengths, ensuring a flawless finish every time.

Another key feature of these models is their advanced blade technology. The blades are crafted from high-quality steel, increasing their longevity and performance. The designs enable clean cuts, promoting healthier grass growth and enhancing the overall appearance of lawns and fields. Additionally, the MDO80-2 is equipped with a double-blade system, which further enhances cutting efficiency and reduces clumping.

The MDO80-2 and DO80-2 also prioritize user comfort and ease of operation. They come with ergonomic controls that ease the strain on operators during extended use. The intuitive design of the control panel simplifies operation, allowing users to focus on their tasks without getting bogged down by complicated settings.

For enhanced maneuverability, both models feature a smooth turning radius, making them ideal for navigating tight spaces. Whether working in a residential yard or a larger agricultural field, operators benefit from the agility these machines provide.

In terms of maintenance, Woods Equipment has developed the MDO80-2 and DO80-2 with user-friendliness in mind. The models are designed for easy access to critical components, simplifying routine maintenance tasks. This design philosophy not only prolongs the lifespan of the equipment but also minimizes downtime.

Overall, the Woods Equipment MDO80-2 and DO80-2 are exceptional choices for those seeking high-performance mowing solutions. With their durable construction, advanced cutting technologies, and user-friendly features, these models are well-suited for fulfilling the demands of any mowing operation, making them a reliable investment for years to come.