Woods Equipment MDO80-2 Operation, Tractor Stability, Attaching Cutter to Tractor 3-POINT Models

Page 13

OPERATION

The designed and tested safety of this machine depends on it being operated within the limitations as explained in this manual. Be familiar with and follow all safety rules in the manual, on the cutter and on the tractor.

The safe operation of this cutter is the responsibility of the operator, who must be properly trained. The opera- tor should be familiar with the equipment and all safety practices before starting operation. Read the Safety Rules on page 7 through page 12.

Information specific to attaching or operating the mounted or towed unit will be identified in the text. Information applicable to either unit will not be segre- gated.

This cutter is designed for shredding heavy brush, such as prunings in orchards, groves and vineyards. Other applications include topping onion sets and potatoes before harvesting. It may also be used to shred green manure crops, straw and stubble, asparagus residue etc. prior to plowing. Recommended tractor ground speed for most mowing conditions is from 1 to 5 mph. Always operate tractor PTO at 540 rpm.

DANGER

Full chain shielding, designed to reduce the possibility of thrown objects, must be installed when operating in populated areas or other areas where thrown objects could injure people or dam- age property. If this machine is not equipped with full chain shielding, operation must be stopped when anyone comes within 300 feet.

WARNING

Never allow children or untrained persons to operate equipment.

Keep bystanders away from equipment.

Before performing any service or maintenance, lower equipment to ground or block securely, turn off engine, remove key, and disconnect driveline from tractor PTO.

On pull-type units, a pin is installed to prevent the height adjustment crank from detaching. Do not operate or service unit unless pin is installed.

Keep all persons away from operator control area while performing adjustments, service, or maintenance.

CAUTION

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

TRACTOR STABILITY

WARNING

A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, tractor could tip over, causing personal injury or death. The weight may be attained with a loader, front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate.

ATTACHING CUTTER TO TRACTOR (3-POINT MODELS)

WARNING

Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

MD80 Mounting

Standard Category 1 mounting pins are used when attaching cutter to tractor. Also available for mounting are optional Category 2 pins and a bushing kit.

Check to be sure mounting pins are properly torqued - Category 1: 300 lbs-ft.; Category 2: 450 lbs-ft.

Install tractor lower lift arms over the cutter mounting pins. Attach tractor top link in top hole of cutter A- frame. Use bushing over top link clevis pin when mounting on a Category 2 tractor.

15916 (Rev. 3/30/2007)

Operation 13

 

 

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Rotary Cutter To the Dealer IntroductionLEA EL Instructivo Table of ContentsTractor Requirements SpecificationsGeneral Information Safety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishPreparation Safety RulesTraining Operation MaintenanceTransportation Storage Serial Number Plate Safety & Instructional DecalsRED Rear Reflector To Avoid Serious Injury or DeathBe Careful Rotating Blades Thrown ObjectsOperation OperationTractor Stability Attaching Cutter to Tractor 3-POINT ModelsShorten Driveline Driveline AttachmentCutting Height Adjustment Without Tailwheel or Check Chains Cutting Height Adjustment for MD80 Mounted Cutter FigureCutting Height Adjustment With Tailwheel or Check Chains Attaching Cutter to Tractor PULL-TYPE Models Cutting Height Adjustment for D80 Pull-Type Cutter FigurePRE-OPERATION Check List Starting and Stopping CutterOperating Technique CleaningOwners Service Owner ServiceLubrication Information Figure Blade Removal Figure Blade Servicing FigureBelt Installation Figure Blade InstallationBlade Sharpening Chain ShieldingSplit Rim Tire Servicing Servicing Tires SafelyDealer Service Dealer ServiceGearbox Maintenance Gearbox Adjustment Gearbox AssemblyAssembly Blade Spindle Repair FigureJoint Disassembly Shield Bearing ServiceUniversal Joint Repair Joint Assembly Servicing Tires Safely Problem Possible Cause Solution Trouble ShootingAssembly AssemblyBlade Installation Figure Distribution Baffle Installation FigureWheel Yoke Installation for DO80-2 Pull- Type Cutter Figure Chain Shielding Installation FigureGearbox Lubrication Tongue and H-Frame Assembly Optional Hydraulic Lift Assembly Tongue Installation for DO80-2 Pull-Type Cutter FigureDriveline Installation MD80 Assembly FigureFrame and Lift Installation Optional Leaf Mulcher Installation FigureOptional Check Chain Installation Optional Check Chain Installation FigureDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListDealer Check Lists Parts Index to Parts ListPart QTY Description DO80-2 Main Frame Assembly PULL-TYPEMDO80-2 Main Frame Assembly Mounted Model DO80-2 & MDO80-2 Main Frame Assembly Common Parts 2390 DO80-2 Front 2/3 of 3-JOINT Drive Square Shaft DO80-2 Front 2/3 of 3-JOINT Drive TWO-LOBE Shaft DO80-2 & MDO80-2 Rear Section of Univeral Drive MDO80-2 Front 1/2 of Universal DriveGearbox Repair Kit DO80-2 & MDO80-2 Gearbox AssemblyDO80-2 & MDO80-2 Blades DO80-2 & MDO80-2 Blade Spindle AssemblyDO80-2 & MDO80-2 Chain Shielding Assembly DO80-2 Parking Jack DO80-2 & MDO80-2 Idler Pulley AssemblyDO80-2 SPRING-LOADED Wheel Yoke DO80-2 Height Adjustment CrankDO80-2 Laminated Tire with HUB & Axle DO80-2 RIM & Axle AssemblySOL ID T IRE DO80-2 Aircraft Tire & HUBMDO80-2 Tailwheel Assembly DO80-2 Hydraulic Hose KIT & Fittings Optional DO80-2 Pivot Link KIT OptionalDO80-2 3-1/2 X 8 Hydraulic Cylinder #10475 Optional MDO80-2 Check Chain Assembly Optional DO80-2 & MDO80-2 Leaf Mulcher Assembly OptionalMDO80-2 Category 2 Bushing KIT MDO80-2 Category 2 Hitch PIN OptionsParts SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Warranty

DO80-2, MDO80-2 specifications

The Woods Equipment MDO80-2 and DO80-2 are robust and innovative pieces of machinery designed to meet the demands of both commercial and agricultural applications. Renowned for their efficiency and performance, these models have garnered attention for their advanced features and technologies that enhance productivity.

One of the standout characteristics of the MDO80-2 and DO80-2 is their powerful cutting capabilities. Equipped with a heavy-duty steel frame, both models provide exceptional durability, allowing them to withstand rigorous use in various conditions. The cutting decks are designed for superior grass trimming, reducing the need for multiple passes and saving valuable time. The adjustable cutting height offers versatility, accommodating different grass types and lengths, ensuring a flawless finish every time.

Another key feature of these models is their advanced blade technology. The blades are crafted from high-quality steel, increasing their longevity and performance. The designs enable clean cuts, promoting healthier grass growth and enhancing the overall appearance of lawns and fields. Additionally, the MDO80-2 is equipped with a double-blade system, which further enhances cutting efficiency and reduces clumping.

The MDO80-2 and DO80-2 also prioritize user comfort and ease of operation. They come with ergonomic controls that ease the strain on operators during extended use. The intuitive design of the control panel simplifies operation, allowing users to focus on their tasks without getting bogged down by complicated settings.

For enhanced maneuverability, both models feature a smooth turning radius, making them ideal for navigating tight spaces. Whether working in a residential yard or a larger agricultural field, operators benefit from the agility these machines provide.

In terms of maintenance, Woods Equipment has developed the MDO80-2 and DO80-2 with user-friendliness in mind. The models are designed for easy access to critical components, simplifying routine maintenance tasks. This design philosophy not only prolongs the lifespan of the equipment but also minimizes downtime.

Overall, the Woods Equipment MDO80-2 and DO80-2 are exceptional choices for those seeking high-performance mowing solutions. With their durable construction, advanced cutting technologies, and user-friendly features, these models are well-suited for fulfilling the demands of any mowing operation, making them a reliable investment for years to come.
Top Page Image Contents