Woods Equipment MDO80-2 manual Blade Servicing Figure, Blade Removal Figure

Page 19

 

 

 

1

 

 

 

PULL-TYPE

 

7

 

 

PULL-TYPE

 

13

1

12

 

 

 

 

 

11

 

 

14

 

 

 

 

4

 

2

9

 

 

 

 

 

 

10

 

 

 

5

6

 

 

 

 

3

7

8

9

CD3847

MOUNTED

Figure 7. Lubrication Points

BLADE SERVICING (FIGURE 8)

WARNING

On pull-type units, a pin is installed to prevent the height adjustment crank from detaching. Do not operate or service unit unless pin is installed.

Blocking the cutter before working underneath provides additional safety. If a mechanical or hydraulic failure occurs, the blocks will support the cutter and prevent anyone under it from being crushed.

Inspect blades, each time before operating cutter, for condition and proper installation. Check to be sure blades are snug but still swivel on blade pin (see Blade Installation, page 20). Replace any blade that is bent, excessively nicked, worn or has any other damage. Small nicks can be ground out when sharpening.

Blade Removal (Figure 8)

Rotate crossbar until blade pin assembly is directly below access hole in rear of cutter frame. Remove bolt

(1)and blade pin lock clip (2). Slide keyhole plate (3) out of blade pin groove and remove. Remove spacers and drive pin out of crossbar.

NOTICE

■If blade pin is seized in crossbar and extreme force will be required to remove it, support cross- bar from below to prevent damage to spindle.

CAUTION

Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

15916 (Rev. 3/30/2007)

Owner Service 19

 

 

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Rotary Cutter To the Dealer IntroductionLEA EL Instructivo Table of ContentsTractor Requirements SpecificationsGeneral Information Safety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishPreparation Safety RulesTraining Operation MaintenanceTransportation Storage Serial Number Plate Safety & Instructional DecalsRED Rear Reflector To Avoid Serious Injury or DeathBe Careful Rotating Blades Thrown ObjectsAttaching Cutter to Tractor 3-POINT Models OperationOperation Tractor StabilityShorten Driveline Driveline AttachmentCutting Height Adjustment Without Tailwheel or Check Chains Cutting Height Adjustment for MD80 Mounted Cutter FigureCutting Height Adjustment With Tailwheel or Check Chains Starting and Stopping Cutter Cutting Height Adjustment for D80 Pull-Type Cutter FigureAttaching Cutter to Tractor PULL-TYPE Models PRE-OPERATION Check ListOperating Technique CleaningOwners Service Owner ServiceLubrication Information Figure Blade Removal Figure Blade Servicing FigureChain Shielding Blade InstallationBelt Installation Figure Blade SharpeningSplit Rim Tire Servicing Servicing Tires SafelyDealer Service Dealer ServiceGearbox Maintenance Blade Spindle Repair Figure Gearbox AssemblyGearbox Adjustment AssemblyJoint Disassembly Shield Bearing ServiceUniversal Joint Repair Joint Assembly Servicing Tires Safely Problem Possible Cause Solution Trouble ShootingDistribution Baffle Installation Figure AssemblyAssembly Blade Installation FigureWheel Yoke Installation for DO80-2 Pull- Type Cutter Figure Chain Shielding Installation FigureGearbox Lubrication Tongue and H-Frame Assembly Optional Hydraulic Lift Assembly Tongue Installation for DO80-2 Pull-Type Cutter FigureDriveline Installation MD80 Assembly FigureFrame and Lift Installation Optional Leaf Mulcher Installation FigureOptional Check Chain Installation Optional Check Chain Installation FigureDelivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListDealer Check Lists Parts Index to Parts ListPart QTY Description DO80-2 Main Frame Assembly PULL-TYPEMDO80-2 Main Frame Assembly Mounted Model DO80-2 & MDO80-2 Main Frame Assembly Common Parts 2390 DO80-2 Front 2/3 of 3-JOINT Drive Square Shaft DO80-2 Front 2/3 of 3-JOINT Drive TWO-LOBE Shaft DO80-2 & MDO80-2 Rear Section of Univeral Drive MDO80-2 Front 1/2 of Universal DriveGearbox Repair Kit DO80-2 & MDO80-2 Gearbox AssemblyDO80-2 & MDO80-2 Blades DO80-2 & MDO80-2 Blade Spindle AssemblyDO80-2 & MDO80-2 Chain Shielding Assembly DO80-2 Parking Jack DO80-2 & MDO80-2 Idler Pulley AssemblyDO80-2 SPRING-LOADED Wheel Yoke DO80-2 Height Adjustment CrankDO80-2 Laminated Tire with HUB & Axle DO80-2 RIM & Axle AssemblySOL ID T IRE DO80-2 Aircraft Tire & HUBMDO80-2 Tailwheel Assembly DO80-2 Hydraulic Hose KIT & Fittings Optional DO80-2 Pivot Link KIT OptionalDO80-2 3-1/2 X 8 Hydraulic Cylinder #10475 Optional MDO80-2 Check Chain Assembly Optional DO80-2 & MDO80-2 Leaf Mulcher Assembly OptionalMDO80-2 Category 2 Bushing KIT MDO80-2 Category 2 Hitch PIN OptionsParts Metric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty Warranty

DO80-2, MDO80-2 specifications

The Woods Equipment MDO80-2 and DO80-2 are robust and innovative pieces of machinery designed to meet the demands of both commercial and agricultural applications. Renowned for their efficiency and performance, these models have garnered attention for their advanced features and technologies that enhance productivity.

One of the standout characteristics of the MDO80-2 and DO80-2 is their powerful cutting capabilities. Equipped with a heavy-duty steel frame, both models provide exceptional durability, allowing them to withstand rigorous use in various conditions. The cutting decks are designed for superior grass trimming, reducing the need for multiple passes and saving valuable time. The adjustable cutting height offers versatility, accommodating different grass types and lengths, ensuring a flawless finish every time.

Another key feature of these models is their advanced blade technology. The blades are crafted from high-quality steel, increasing their longevity and performance. The designs enable clean cuts, promoting healthier grass growth and enhancing the overall appearance of lawns and fields. Additionally, the MDO80-2 is equipped with a double-blade system, which further enhances cutting efficiency and reduces clumping.

The MDO80-2 and DO80-2 also prioritize user comfort and ease of operation. They come with ergonomic controls that ease the strain on operators during extended use. The intuitive design of the control panel simplifies operation, allowing users to focus on their tasks without getting bogged down by complicated settings.

For enhanced maneuverability, both models feature a smooth turning radius, making them ideal for navigating tight spaces. Whether working in a residential yard or a larger agricultural field, operators benefit from the agility these machines provide.

In terms of maintenance, Woods Equipment has developed the MDO80-2 and DO80-2 with user-friendliness in mind. The models are designed for easy access to critical components, simplifying routine maintenance tasks. This design philosophy not only prolongs the lifespan of the equipment but also minimizes downtime.

Overall, the Woods Equipment MDO80-2 and DO80-2 are exceptional choices for those seeking high-performance mowing solutions. With their durable construction, advanced cutting technologies, and user-friendly features, these models are well-suited for fulfilling the demands of any mowing operation, making them a reliable investment for years to come.
Top Page Image Contents