Assembly, Dealer SET-UP Instructions | Woods Equipment DO80-2

Woods Equipment MDO80-2 manual Assembly, Dealer SET-UP Instructions, Blade Installation Figure

ASSEMBLY

DEALER SET-UP INSTRUCTIONS

These instructions are for the assembly of the MD80 and D80. Many of the procedures apply to both units. When an instruction applies to a specific unit, the sec- tion heading will indicate which unit.

Assembly of this cutter is the responsibility of the WOODS dealer. It should be delivered to the owner completely assembled, lubricated and adjusted for nor- mal cutting conditions. Complete check lists when assembly is complete.

The cutter is shipped partially assembled. Assembly will be easier if components are aligned and loosely assembled before tightening hardware. Recommended torque values for hardware are located on page 58.

Select a suitable working area. Open parts boxes and lay out parts and hardware to make location easy. Refer to illustrations, accompanying text, parts lists and exploded view drawings.

WARNING

Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

CAUTION

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

Blade Installation (Figure 20)

Either place cutter on stands or hang to permit access to both top and bottom. Make sure cutter is secured to prevent it from falling.

Liberally coat blade pin and crossbar hole with Never- Seez® or equivalent. Make sure blade is offset away from deck and cutting edge is positioned for counter- clockwise rotation as viewed from top of deck.

Install blade pin (9) up through blade (8) then through hole in crossbar and push firmly against crossbar (7). Install as many spacers (4, 5 or 6) as possible and still be able to slide keyhole plate (3), with ears up as shown, into blade pin groove. Place blade pin clip (2) over keyhole plate and into blade pin groove. Secure with bolt (1). Repeat for opposite blade.

Blade should be snug but swivel on pin without exces- sive force. Retain any spacers not used in installation for use when blade wears or on future installations.

1.	Bolt		1
2.	Blade pin clip		2
3.	Keyhole plate		2
3.	Keyhole plate		3
4.	Spacer		3
4.	Spacer
5.	18 GA Spacer		4
6.	20 GA Spacer		4
6.	20 GA Spacer		5
7.	Crossbar		5
7.	Crossbar	8
8.	Blade	8	6
8.	Blade		6
9.	Blade pin		7
			7

CD3818

Figure 20. Blade Installation

Distribution Baffle Installation (Figure 21)

A distribution baffle is supplied. It is recommended when mowing grass and weeds. It should not be used when operating cutter in heavy brush. Remove the two rear carriage bolts from the left side skid. Place baffle

(1)under cutter frame and attach as shown.

1.Distribution baffle

2.1/2 x 1" Bolt

3.1/2" Flanged hex lock nut

4.5/8 x 2" Carriage bolt

5.3/4" Flat washer

6.5/8" Flat washer

7.5/8" Nut

Figure 21. Distribution Baffle Installation

28 Assembly	15916 (Rev. 3/30/2007)

DO80-2, MDO80-2 specifications

The Woods Equipment MDO80-2 and DO80-2 are robust and innovative pieces of machinery designed to meet the demands of both commercial and agricultural applications. Renowned for their efficiency and performance, these models have garnered attention for their advanced features and technologies that enhance productivity.

One of the standout characteristics of the MDO80-2 and DO80-2 is their powerful cutting capabilities. Equipped with a heavy-duty steel frame, both models provide exceptional durability, allowing them to withstand rigorous use in various conditions. The cutting decks are designed for superior grass trimming, reducing the need for multiple passes and saving valuable time. The adjustable cutting height offers versatility, accommodating different grass types and lengths, ensuring a flawless finish every time.

Another key feature of these models is their advanced blade technology. The blades are crafted from high-quality steel, increasing their longevity and performance. The designs enable clean cuts, promoting healthier grass growth and enhancing the overall appearance of lawns and fields. Additionally, the MDO80-2 is equipped with a double-blade system, which further enhances cutting efficiency and reduces clumping.

The MDO80-2 and DO80-2 also prioritize user comfort and ease of operation. They come with ergonomic controls that ease the strain on operators during extended use. The intuitive design of the control panel simplifies operation, allowing users to focus on their tasks without getting bogged down by complicated settings.

For enhanced maneuverability, both models feature a smooth turning radius, making them ideal for navigating tight spaces. Whether working in a residential yard or a larger agricultural field, operators benefit from the agility these machines provide.

In terms of maintenance, Woods Equipment has developed the MDO80-2 and DO80-2 with user-friendliness in mind. The models are designed for easy access to critical components, simplifying routine maintenance tasks. This design philosophy not only prolongs the lifespan of the equipment but also minimizes downtime.

Overall, the Woods Equipment MDO80-2 and DO80-2 are exceptional choices for those seeking high-performance mowing solutions. With their durable construction, advanced cutting technologies, and user-friendly features, these models are well-suited for fulfilling the demands of any mowing operation, making them a reliable investment for years to come.