Woods Equipment MDO80-2 manual Gearbox Lubrication, Chain Shielding Installation Figure

Page 29

1.Chain shield assembly

2.3/8 x 19-3/4" Threaded rod

3.3/8" Hex lock nut

4.1/2 x 1" Bolt

5.1/2" Flanged lock nut

Figure 22. Chain Shielding Assembly

Gearbox Lubrication

NOTICE

The gearbox was not filled at the factory. It must be serviced before operating cutter. Failure to service will result in damage to the gearbox.

Chain Shielding Installation (Figure 22)

DANGER

Full chain shielding, designed to reduce the possibility of thrown objects, must be installed when operating in populated areas or other areas where thrown objects could injure people or dam- age property. If this machine is not equipped with full chain shielding, operation must be stopped when anyone comes within 300 feet.

All four chain assemblies (1) are interchangeable. Place each assembly on the cutter and attach by inserting bolt (4) up through the cutter and chain shield assembly, then install flange lock nut (5) on each bolt.

The drag rods (2) are sold separately. To install, place a lock nut (3) on one end and thread rod (2) through bot-

tom of 16 chain links, then secure with another lock nut

(3). Two rods (2) are used on each chain shield assem- bly (1).

Wheel Yoke Installation for DO80-2 Pull- Type Cutter (Figure 23)

The wheel yoke for use with pneumatic tires is illus- trated. The spring-loaded wheel yoke installs the same.

Attach wheel yoke (6) to rear of cutter frame with clevis pins (15) and cotter pins (3) at two points.

Insert crank (5) through pivot block (10). Slide sleeve

(7)onto crank, align hole in sleeve and hole in crank, and drive the spirol pin (8) into the assembly to attach.

Thread pivot nut (2) onto crank (5) until it will install into pivot lug (1), then attach with cotter pin (3). Install spirol pin (4) into crank (5) to prevent crank detachment.

Attach axle with rim (12) and tire (not supplied) to wheel yoke using lock washer (13) and nut (14).

NOTICE

You must use the pneumatic tire with this wheel yoke. The solid tire may be used with the spring-loaded wheel yoke.

15916 (Rev. 3/30/2007)

Assembly 29

 

 

Image 29
Contents Rotary Cutter To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsTractor Requirements Safety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishTraining Safety RulesPreparation Transportation MaintenanceOperation Storage Serial Number Plate Safety & Instructional DecalsRED Rear Reflector To Avoid Serious Injury or DeathBe Careful Rotating Blades Thrown ObjectsOperation OperationTractor Stability Attaching Cutter to Tractor 3-POINT ModelsShorten Driveline Driveline AttachmentCutting Height Adjustment With Tailwheel or Check Chains Cutting Height Adjustment for MD80 Mounted Cutter FigureCutting Height Adjustment Without Tailwheel or Check Chains Attaching Cutter to Tractor PULL-TYPE Models Cutting Height Adjustment for D80 Pull-Type Cutter FigurePRE-OPERATION Check List Starting and Stopping CutterOperating Technique CleaningLubrication Information Figure Owner ServiceOwners Service Blade Removal Figure Blade Servicing FigureBelt Installation Figure Blade InstallationBlade Sharpening Chain ShieldingSplit Rim Tire Servicing Servicing Tires SafelyGearbox Maintenance Dealer ServiceDealer Service Gearbox Adjustment Gearbox AssemblyAssembly Blade Spindle Repair FigureUniversal Joint Repair Shield Bearing ServiceJoint Disassembly Joint Assembly Servicing Tires Safely Problem Possible Cause Solution Trouble ShootingAssembly AssemblyBlade Installation Figure Distribution Baffle Installation FigureGearbox Lubrication Chain Shielding Installation FigureWheel Yoke Installation for DO80-2 Pull- Type Cutter Figure Tongue and H-Frame Assembly Optional Hydraulic Lift Assembly Tongue Installation for DO80-2 Pull-Type Cutter FigureDriveline Installation MD80 Assembly FigureFrame and Lift Installation Optional Leaf Mulcher Installation FigureOptional Check Chain Installation Optional Check Chain Installation FigureDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListDealer Check Lists Parts Index to Parts ListPart QTY Description DO80-2 Main Frame Assembly PULL-TYPEMDO80-2 Main Frame Assembly Mounted Model DO80-2 & MDO80-2 Main Frame Assembly Common Parts 2390 DO80-2 Front 2/3 of 3-JOINT Drive Square Shaft DO80-2 Front 2/3 of 3-JOINT Drive TWO-LOBE Shaft DO80-2 & MDO80-2 Rear Section of Univeral Drive MDO80-2 Front 1/2 of Universal DriveGearbox Repair Kit DO80-2 & MDO80-2 Gearbox AssemblyDO80-2 & MDO80-2 Blades DO80-2 & MDO80-2 Blade Spindle AssemblyDO80-2 & MDO80-2 Chain Shielding Assembly DO80-2 Parking Jack DO80-2 & MDO80-2 Idler Pulley AssemblyDO80-2 SPRING-LOADED Wheel Yoke DO80-2 Height Adjustment CrankDO80-2 Laminated Tire with HUB & Axle DO80-2 RIM & Axle AssemblySOL ID T IRE DO80-2 Aircraft Tire & HUBMDO80-2 Tailwheel Assembly DO80-2 Hydraulic Hose KIT & Fittings Optional DO80-2 Pivot Link KIT OptionalDO80-2 3-1/2 X 8 Hydraulic Cylinder #10475 Optional MDO80-2 Check Chain Assembly Optional DO80-2 & MDO80-2 Leaf Mulcher Assembly OptionalMDO80-2 Category 2 Bushing KIT MDO80-2 Category 2 Hitch PIN OptionsParts SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Warranty

DO80-2, MDO80-2 specifications

The Woods Equipment MDO80-2 and DO80-2 are robust and innovative pieces of machinery designed to meet the demands of both commercial and agricultural applications. Renowned for their efficiency and performance, these models have garnered attention for their advanced features and technologies that enhance productivity.

One of the standout characteristics of the MDO80-2 and DO80-2 is their powerful cutting capabilities. Equipped with a heavy-duty steel frame, both models provide exceptional durability, allowing them to withstand rigorous use in various conditions. The cutting decks are designed for superior grass trimming, reducing the need for multiple passes and saving valuable time. The adjustable cutting height offers versatility, accommodating different grass types and lengths, ensuring a flawless finish every time.

Another key feature of these models is their advanced blade technology. The blades are crafted from high-quality steel, increasing their longevity and performance. The designs enable clean cuts, promoting healthier grass growth and enhancing the overall appearance of lawns and fields. Additionally, the MDO80-2 is equipped with a double-blade system, which further enhances cutting efficiency and reduces clumping.

The MDO80-2 and DO80-2 also prioritize user comfort and ease of operation. They come with ergonomic controls that ease the strain on operators during extended use. The intuitive design of the control panel simplifies operation, allowing users to focus on their tasks without getting bogged down by complicated settings.

For enhanced maneuverability, both models feature a smooth turning radius, making them ideal for navigating tight spaces. Whether working in a residential yard or a larger agricultural field, operators benefit from the agility these machines provide.

In terms of maintenance, Woods Equipment has developed the MDO80-2 and DO80-2 with user-friendliness in mind. The models are designed for easy access to critical components, simplifying routine maintenance tasks. This design philosophy not only prolongs the lifespan of the equipment but also minimizes downtime.

Overall, the Woods Equipment MDO80-2 and DO80-2 are exceptional choices for those seeking high-performance mowing solutions. With their durable construction, advanced cutting technologies, and user-friendly features, these models are well-suited for fulfilling the demands of any mowing operation, making them a reliable investment for years to come.