Woods Equipment RDC54, RD60, RD72 manual Description Frequency

Page 16

7

8

6 5

4

3

2

10 1

9

Ref

Description

Frequency

No.

 

 

1

Front U-Joint

8 Hours

2

Caster Wheel (Four wheels)

8 Hours

3

Caster Pivot (Four wheels)

8 Hours

4

Left Spindle (Access through hole)

40 Hours

5

Shield Bearings

8 Hours

6

Rear U-Joint

8 Hours

7

Gearbox (Fill to center of horizontal shaft with

Check Daily

 

SAE 80W or 90W gear lube)

For Leakage

8

Right Spindle (Access through hole)

40 Hours

9

Center Spindle (Access through hole)

40 Hours

10

Slip Joint

40 Hours

 

 

 

 

Figure 8. Lubrication Points & Chart

 

Severe or unusual conditions may require more fre- quent lubrication. Some reference numbers have more than one location; be sure you lubricate all locations.

Use a lithium grease of #2 consistency with a MOLY (molybdenum disulfide) additive for all locations. Be sure to clean fittings thoroughly before attaching grease gun. When applied according to the lubrication chart, one good pump of most guns is sufficient.

Use SAE 90W gear lube in the gearbox. Fill to plug on side of gearbox.

Check gearbox daily for evidence of leakage at both seals and the gasket between the housing and cover. If leakage is noted, repair immediately. There may be a small amount of lube emitted from the vent plug; this is not considered leakage.

Overfilling the gearbox will cause the excess gear lube to blow out vent plug and ruin the belt.

14 Owner Service

MAN0260 (8/6/2004)

 

 

Image 16
Contents Heritage Rear Discharge Mower Introduction To the DealerTable of Contents LEA EL InstructivoGeneral Information SpecificationsRD60 RD72 Safety Safety RulesTraining PreparationMaintenance TransportationStorage Safety & Instructional Decals 1003751Replace Immediately If Damaged Be CarefulRespirator or filter mask where appropriate OperationOperation Tractor StabilityAttachment Points Tether Chain Tractor Top Link Adjustment Front Caster Wheel Interference CheckFront Roller Optional Operating TechniqueRemoving Mower from Tractor Storage Mower Storage PositionOwner PRE-OPERATION Check List Owners ResponsibilityOwner Service Owner ServiceBlocking Method Lubrication InformationDescription Frequency Service Belt Install BeltService Blade Driveshaft LubricationInstall Blades CleaningSharpen Blades Chain ShieldingPeriodically or Before Extended Storage Troubleshooting Mowing ConditionsTrouble Shooting Belt ConditionsDealer Service Blade Spindle RepairRemove Spindle Disassemble SpindleSeal Replacement Seal InstallationAssemble Spindle Gearbox RepairSeal Installation Vertical Shaft Seal Replacement Horizontal Shaft Seal ReplacementRemove Gearbox from Mower Disassemble GearboxInstall Gearbox Install Drive SheaveRD60 & RD72 All ModelsJoint Disassembly Universal Joint RepairJoint Assembly Assembly Assembly InstructionsInstall A-Frame Arms Dealer SET-UP InstructionsInstall Rear Offset Link Arms Install Top LinkInstall Driveshaft Install Chain Shielding OptionalInstall Quick Hitch Kit Optional RD60 & RD72 Only X 4-3/4 HhcsInstall Front Roller Optional Front Roller InstallationDealer Check Lists Dealer Check ListsDealer PRE-DELIVERY Check List Dealer Delivery Check ListParts PartsBolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Rev /23/2005 MAN0260