Woods Equipment BW180HDQ, BW180HB manual Joint Assembly, Servicing Tires Safely

Page 32

4.Place universal cross in vise as shown in Figure 22 and tap on yoke to remove cup. Repeat Step 3 for final removal. Drive remaining cup out with a drift and hammer.

Figure 22

U-Joint Assembly

1.Place seals securely on bearing cups. Insert cup into yoke from outside and press in with hand pressure as far as possible. Insert journal cross into bearing cup with grease fitting away from shaft. Be careful not to disturb needle bearings. Insert another bearing cup directly across from first cup and press in as far as possible with hand pressure.

2.Trap cups in vise and apply pressure. Be sure journal cross is started into bearings and continue pressure with vise, squeezing in as far as possible. Tapping the yoke will help.

3.Seat cups by placing a drift or socket (slightly smaller than the cup) on cup and rap with a hammer. Install snap ring and repeat on opposite cup.

4.Repeat Step 1 and Step 2 to install remaining cups in remaining yoke.

5.Move both yokes in all directions to check for free movement. If movement is restricted, rap on yokes sharply with a hammer to relieve any tension. Repeat until both yokes move in all directions without restriction.

SERVICING TIRES SAFELY

Used Aircraft Tires (Figure 23)

WARNING

Do not attempt to mount a tire unless you have the proper equipment and experience to perform the job.

Always maintain the correct tire pressure. Do not inflate tires above the recommended pressure. Never weld or heat a wheel and tire assembly. The heat can cause an increase in air pressure and result in a tire explosion. Welding can structurally weaken or deform the wheel.

When inflating tires, use a clip-on chuck and an exten- sion hose long enough to allow you to stand to the side

—not in front of or over the tire assembly. Use a safety cage if available.

Check wheels for low pressure, cuts, bubbles, dam- aged rims, or missing lug bolts and nuts.

Never remove split rim assembly hardware (A) with the tire inflated.

A

PN 1006348

Figure 23. Split Rim Tire Servicing

32 Dealer Service

MAN0805 (4/30/2009)

 

 

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Batwing Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules InstallationTraining PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be Careful1000 RPM Safety Connecting Cutter to Tractor OperationOperation Hydraulic ConnectionCutting Height Adjustment Interference CheckCV Driveline Turning Limits Tractor OperationShredding Cutter OperationMowing Tips Transporting Lock-UpPRE-OPERATION Check List Owners ResponsibilityBlocking Method Owner ServiceOwner Service Driveline Lubrication LubricationGearbox Lubrication Blade Installation Figure Seasonal LubricationBlades Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningServicing Tires Safely CleaningShielding Repair Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal Replacement FigureRemoval from Cutter Figure Disassembly FigureGearbox Repair Reinstallation GearboxSplitter Gearbox Repair Figure Removal from Cutter DisassemblyAssembly Reinstallation on Cutter Check GearboxCrossbar Removal Crossbar RemovalUniversal Joint Repair Crossbar InstallationJoint Disassembly Joint Assembly Dealer SET-UP Instructions AssemblyAssembly Instructions Install Height Adjustment Cylinder BW180HD Install SMV Emblem BW180HDInstall Wheel and Hub BW180HD Install Tongue BW180HDInstall 3-Joint Drive 540 RPM Only BW180HD Joint Drive InstallationInstall Wing Cylinder & Lock-up Bar BW180HD Install CV Drive BW180HD- OptionalInstall Wing BW180HD Install Wing Wheel and Hub All Models Left Wing Lock-Up Bar InstalledInstall Wing Wheel Yoke Adjustment Link BW180HD Install Wing Driveline BW180HDInstall Hose Kit BW180HD Winch Kit Installation OptionalInstall Chain or Belt Shielding BW180HD Chain Shielding Installation Center SectionChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMAN0805 4/30/2009 Parts BW180HD, BW180HDQ BW180HB, BW180HBQ BW126HB, BW126HBQMain Frame Assembly Front Section Part QTY Description BW180HD Main Frame Assembly Rear Section Tire & hub see BW180HB Main Frame Assembly Rear Section REF Part QTY Description Wing Assembly See Wing & Center Gearbox Assembly Center Splitter Gearbox Assembly Gear, 540 rpmCenter Deck Drive Assembly Front Drive Assembly Equal Angle Rear Drive Assembly Equal Angle Type a 540 RPM & 1000 RPM Front CV Drive Type B 540 RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly 1027468 Rubber Shielding Wing Front & Rear Standard on BW180 Models Chain Shielding Center Section Front & Rear Single ROW Double ROWChain Shielding Wing Front & Rear Single ROWHydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITBW126HB / BW126HBQ Weight BOX Assembly Optional Winch Kit Operation Winch Kit InstallationWinch KIT Optional Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Rev /23/2005

BW180HDQ, BW180HD, BW180HB specifications

Woods Equipment has long been a leader in the agricultural and landscaping industry, providing exceptional products that enhance productivity and efficiency. Among its standout offerings are the BW180HB, BW180HD, and BW180HDQ models. These versatile implements are primarily designed for use with tractors, making them invaluable for a variety of tasks.

The BW180HB model is known for its high-performance capabilities combined with a compact design. One of its main features is its heavy-duty construction, which ensures durability and longevity even under strenuous conditions. The implement is equipped with a balanced weight distribution system that allows for better stability and control during operation. Additionally, the BW180HB is designed to handle a range of tasks from grading and leveling to scraping and light dozing.

Moving up the series, the BW180HD offers a higher capacity and is built for more demanding applications. This model features a robust hydraulic system that enhances lifting capabilities, allowing operators to tackle heavier loads with ease. Its advanced blade adjustment features allow for precise angle and depth control, making it ideal for a variety of terrains. The BW180HD is particularly praised for its reliability in tough environments, thanks to its reinforced frame and high-quality materials.

The BW180HDQ model represents the pinnacle of Woods Equipment's offerings in this series. It features all the capabilities of the BW180HD but includes advanced technological enhancements for improved performance. The inclusion of an automated hydraulic control system streamlines operations, enabling operators to adjust settings on-the-fly to adapt to changing conditions. Additionally, the BW180HDQ comes with integrated safety features that protect both the operator and the equipment during use.

All three models share several common characteristics that make them preferred choices among landscaping and construction professionals. They are compatible with a wide range of tractor types, ensuring versatility for various users. The quick-connect attachment points allow for rapid changes between implements, saving time and increasing productivity. With easy maintenance designs, these models ensure that downtime is minimized, allowing operators to focus on the task at hand.

In summary, the Woods Equipment BW180HB, BW180HD, and BW180HDQ models are exceptional tools for anyone looking to enhance their operational efficiency in agriculture or landscaping. With their robust features, advanced technologies, and commitment to durability, these implements represent some of the best options available in the market today.
Top Page Image Contents