Woods Equipment BW180HB, BW180HDQ manual Assembly Instructions, Dealer SET-UP Instructions

Page 33

ASSEMBLY INSTRUCTIONS

DEALER SET-UP INSTRUCTIONS

Assembly of this cutter is the responsibility of the WOODS dealer. It should be delivered to the owner completely assembled, lubricated and adjusted for nor- mal cutting conditions.

The BW180HB and BW126HB cutters are shipped completely assembled. The BW180HD cutter is shipped partially assembled. Assembly will be easier if components are aligned and loosely assembled before tightening hardware. Recommended torque values for hardware are located on page 72.

Select a suitable working area. A smooth hard surface, such as concrete, will make assembly much quicker. Open parts boxes and lay out parts and hardware to make location easy. Refer to illustrations, accompany- ing text, parts lists and exploded view drawings.

Complete the check list on page 43 when assembly is complete and cutter is delivered to the customer.

Before working underneath, carefully read Oper- ator’s Manual instructions, disconnect driveline, raise mower, securely block up all corners with jackstands, and check stability. Secure blocking prevents equipment from dropping due to hydrau- lic leak down, hydraulic system failures, or mechanical component failures.

Do not disconnect hydraulic lines until machine is securely blocked or placed in lowest position and system pressure is released by operating valve levers.

CAUTION

Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

Fill Gearboxes (All Models)

1.Remove top and side plugs from gearbox.

2.Fill gearbox with SAE 80W or 90W EP oil until it runs out of side level hole. Install plug in the side hole and vented dipstick in the top.

3.Allow oil to drain into the lower bearings and recheck oil level. Fill all gearboxes.

Install Attitude Rod (BW180HD)

1.Insert attitude rod (6) under splitter gearbox support and through pivot casting in wheel yoke arm assembly. The rod is a very tight fit; use care to prevent thread damage during installation.

2.Slide spacer (16) over rod and loosely install washer (35) and two nuts (34).

 

Attitude Rod Length

Small Aircraft Tires

Beyond Nuts (34)

 

 

Tongue at 11"

3.5

 

 

Tongue at 18"

1.75

 

 

Large Aircraft Tires

 

 

 

Tongue at 11"

4.5

 

 

Tongue at 18"

2.5

 

 

6. Attitude rod

16.1" x 3.75 Spacer, pipe schedule 40 34.1" Hex nut

35.1" Flat washer

Figure 24. Attitude Rod Installed on Wheel Yoke Tube

Install Spring Arm (BW180HD)

Refer to Figure 25.

1.Place spring arm (3), spacers (17), and spring (4) on deck as shown.

2.Secure spring arm and spacers to lugs on deck using clevis pin (19) and two cotter pins (66).

3.Install retaining cap screw (53) and flange lock nut (55).

MAN0805 (4/30/2009)

Assembly 33

 

 

Image 33
Contents Batwing To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsSafety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishInstallation Safety RulesTraining PreparationOperation TransportationMaintenance Storage Be Careful Safety & Instructional Decals1000 RPM Safety Operation Connecting Cutter to TractorOperation Hydraulic ConnectionInterference Check Cutting Height AdjustmentCV Driveline Turning Limits Tractor OperationCutter Operation Mowing TipsShredding Lock-Up TransportingOwners Responsibility PRE-OPERATION Check ListOwner Service Owner ServiceBlocking Method Lubrication Gearbox LubricationDriveline Lubrication Seasonal Lubrication Blade Installation FigureBlades Blade Removal FigureBlade Sharpening Slip Clutch Adjustment FigureCleaning Shielding RepairServicing Tires Safely Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal Replacement FigureDisassembly Figure Gearbox RepairRemoval from Cutter Figure Gearbox ReinstallationDisassembly AssemblySplitter Gearbox Repair Figure Removal from Cutter Check Gearbox Reinstallation on CutterCrossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Joint Assembly Assembly Assembly InstructionsDealer SET-UP Instructions Install SMV Emblem BW180HD Install Height Adjustment Cylinder BW180HDInstall Tongue BW180HD Install Wheel and Hub BW180HDJoint Drive Installation Install 3-Joint Drive 540 RPM Only BW180HDInstall CV Drive BW180HD- Optional Install Wing BW180HDInstall Wing Cylinder & Lock-up Bar BW180HD Left Wing Lock-Up Bar Installed Install Wing Wheel and Hub All ModelsInstall Wing Driveline BW180HD Install Wing Wheel Yoke Adjustment Link BW180HDInstall Hose Kit BW180HD Winch Kit Installation OptionalChain Shielding Installation Center Section Install Chain or Belt Shielding BW180HDChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMAN0805 4/30/2009 BW180HD, BW180HDQ BW180HB, BW180HBQ BW126HB, BW126HBQ PartsMain Frame Assembly Front Section Part QTY Description BW180HD Main Frame Assembly Rear Section Tire & hub see BW180HB Main Frame Assembly Rear Section REF Part QTY Description Wing Assembly See Wing & Center Gearbox Assembly Center Gear, 540 rpm Splitter Gearbox AssemblyCenter Deck Drive Assembly Front Drive Assembly Equal Angle Rear Drive Assembly Equal Angle Type a 540 RPM & 1000 RPM Front CV Drive Type B 540 RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly 1027468 Rubber Shielding Wing Front & Rear Standard on BW180 Models Single ROW Double ROW Chain Shielding Center Section Front & RearSingle ROW Chain Shielding Wing Front & RearHydraulic Cylinders Hydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalBW126HB / BW126HBQ Weight BOX Assembly Optional Winch Kit Installation Winch KIT OptionalWinch Kit Operation SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Rev /23/2005

BW180HDQ, BW180HD, BW180HB specifications

Woods Equipment has long been a leader in the agricultural and landscaping industry, providing exceptional products that enhance productivity and efficiency. Among its standout offerings are the BW180HB, BW180HD, and BW180HDQ models. These versatile implements are primarily designed for use with tractors, making them invaluable for a variety of tasks.

The BW180HB model is known for its high-performance capabilities combined with a compact design. One of its main features is its heavy-duty construction, which ensures durability and longevity even under strenuous conditions. The implement is equipped with a balanced weight distribution system that allows for better stability and control during operation. Additionally, the BW180HB is designed to handle a range of tasks from grading and leveling to scraping and light dozing.

Moving up the series, the BW180HD offers a higher capacity and is built for more demanding applications. This model features a robust hydraulic system that enhances lifting capabilities, allowing operators to tackle heavier loads with ease. Its advanced blade adjustment features allow for precise angle and depth control, making it ideal for a variety of terrains. The BW180HD is particularly praised for its reliability in tough environments, thanks to its reinforced frame and high-quality materials.

The BW180HDQ model represents the pinnacle of Woods Equipment's offerings in this series. It features all the capabilities of the BW180HD but includes advanced technological enhancements for improved performance. The inclusion of an automated hydraulic control system streamlines operations, enabling operators to adjust settings on-the-fly to adapt to changing conditions. Additionally, the BW180HDQ comes with integrated safety features that protect both the operator and the equipment during use.

All three models share several common characteristics that make them preferred choices among landscaping and construction professionals. They are compatible with a wide range of tractor types, ensuring versatility for various users. The quick-connect attachment points allow for rapid changes between implements, saving time and increasing productivity. With easy maintenance designs, these models ensure that downtime is minimized, allowing operators to focus on the task at hand.

In summary, the Woods Equipment BW180HB, BW180HD, and BW180HDQ models are exceptional tools for anyone looking to enhance their operational efficiency in agriculture or landscaping. With their robust features, advanced technologies, and commitment to durability, these implements represent some of the best options available in the market today.